From: Stefano Babic <sbabic@denx.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] Please pull u-boot-imx/next into arm/next
Date: Mon, 26 Sep 2011 13:35:19 +0200 [thread overview]
Message-ID: <4E806377.70701@denx.de> (raw)
Hi Albert,
please pull u-boot-imx/next (already rebased on u-boot-arm/next after
you merged u-boot-ti) into your u-boot-arm/next.
Best regards,
Stefano
The following changes since commit f3340eeaf574b3297e801a563089c90d23e84f8d:
arm, davinci, da8xx: add cpuinfo (2011-09-23 15:50:39 -0400)
are available in the git repository at:
git://www.denx.de/git/u-boot-imx.git next
Fabio Estevam (25):
ARM: mx25: Print the silicon revison
ARM: mx25: Print the source of reset
MX31: mx31pdk: Remove nand_spl config.mk file
MX31: Improve readability for reset cause
mx31pdk: Change the prompt as per other i.MX boards
MX25: tx25: Avoid the usage of extern in C file
MX25: Add initial support for MX25PDK
MX31: Disable watchdog during low-power modes
mx31pdk: Remove dram_init_banksize()
mx25pdk: Remove dram_init_banksize()
mx31ads: Remove dram_init_banksize()
imx31_litekit: Remove dram_init_banksize()
mx31pdk: Place machine ID into board config
mx25pdk: Place machine ID into board config
mx31ads: Place machine ID into board config
imx31_litekit: Place machine ID into board config
mx51evk: Place machine ID into board config
mx53loco: Place machine ID into board config
mx53smd: Place machine ID into board config
mx53ard: Place machine ID into board config
mx53evk: Place machine ID into board config
zmx25: Remove dram_init_banksize()
zmx25: Place machine ID into board config
zmx25: Fix build warning due to 'get_reset_cause' defined but not used
vision2: Place machine ID into board config
Jason Liu (1):
cosmetic: fsl_pmic: cosmetic for the help message
Marek Vasut (19):
EfikaMX: Adjust undocumented magic constant in config file
FEC: Use proper accessor to read register in debug call
FEC: Use defined constant instead of magic number
FEC: Kill mode select FIXME's
FEC: Add RMII mode support
FEC: Allow selection of MII mode via CONFIG_FEC_XCV_TYPE
FEC: Abstract access to fec->eth in MII operations
FEC: Allow multiple FECes
FEC: Allow registering MII postconfiguration callback
FEC: Add timeout for chip reset
FEC: Squish "got MAC from fuse" message, make it debug()
FEC: Move imx_get_mac_from_fuse() definition to fec_mxc.h
MX5: Modify the PLL decoding algorithm
MX5: Add AHB clock reporting and fix IPG clock reporting
MX5: Clean up the output of "clocks" command
I2C: mxc_i2c rework
ATA: Squash warnings in mxc_ata.
EfikaMX: Add imximage config for Efika SB
EfikaSB: Add preliminary EfikaSB support
MAINTAINERS | 2 +
arch/arm/cpu/arm1136/mx31/generic.c | 2 +-
arch/arm/cpu/arm1136/mx31/timer.c | 4 +-
arch/arm/cpu/arm926ejs/mx25/generic.c | 53 +++-
arch/arm/cpu/armv7/mx5/clock.c | 114 +++++--
arch/arm/include/asm/arch-mx25/imx-regs.h | 4 +-
arch/arm/include/asm/arch-mx25/sys_proto.h | 29 ++
arch/arm/include/asm/arch-mx27/imx-regs.h | 1 -
arch/arm/include/asm/arch-mx31/imx-regs.h | 2 +
arch/arm/include/asm/arch-mx35/imx-regs.h | 2 -
arch/arm/include/asm/arch-mx5/crm_regs.h | 11 +
arch/arm/include/asm/arch-mx5/imx-regs.h | 5 +-
board/efikamx/efikamx.c | 124 ++++++--
board/efikamx/{imximage.cfg => imximage_mx.cfg} | 0
board/efikamx/{imximage.cfg => imximage_sb.cfg} | 26 +-
board/freescale/mx25pdk/Makefile | 49 +++
board/freescale/mx25pdk/imximage.cfg | 73 ++++
board/freescale/mx25pdk/lowlevel_init.S | 21 ++
board/freescale/mx25pdk/mx25pdk.c | 56 +++
board/freescale/mx31ads/mx31ads.c | 7 -
board/freescale/mx31pdk/mx31pdk.c | 7 -
board/freescale/mx51evk/mx51evk.c | 1 -
board/freescale/mx53ard/mx53ard.c | 1 -
board/freescale/mx53evk/mx53evk.c | 1 -
board/freescale/mx53loco/mx53loco.c | 1 -
board/freescale/mx53smd/mx53smd.c | 1 -
board/karo/tx25/tx25.c | 3 +-
board/logicpd/imx31_litekit/imx31_litekit.c | 7 -
board/syteco/zmx25/zmx25.c | 8 -
board/ttcontrol/vision2/vision2.c | 1 -
boards.cfg | 5 +-
drivers/block/mxc_ata.c | 22 +-
drivers/i2c/mxc_i2c.c | 422
++++++++++++++++-------
drivers/misc/fsl_pmic.c | 2 +-
drivers/net/fec_mxc.c | 170 ++++++---
drivers/net/fec_mxc.h | 9 +-
include/configs/efikamx.h | 6 +-
include/configs/imx31_litekit.h | 4 +-
include/configs/mx25pdk.h | 108 ++++++
include/configs/mx31ads.h | 2 +
include/configs/mx31pdk.h | 4 +-
include/configs/mx51evk.h | 1 +
include/configs/mx53ard.h | 2 +
include/configs/mx53evk.h | 2 +
include/configs/mx53loco.h | 2 +
include/configs/mx53smd.h | 4 +-
include/configs/vision2.h | 2 +
include/configs/zmx25.h | 1 +
include/netdev.h | 7 +-
nand_spl/board/freescale/mx31pdk/Makefile | 2 +-
nand_spl/board/freescale/mx31pdk/config.mk | 1 -
51 files changed, 1073 insertions(+), 321 deletions(-)
create mode 100644 arch/arm/include/asm/arch-mx25/sys_proto.h
copy board/efikamx/{imximage.cfg => imximage_mx.cfg} (100%)
rename board/efikamx/{imximage.cfg => imximage_sb.cfg} (90%)
create mode 100644 board/freescale/mx25pdk/Makefile
create mode 100644 board/freescale/mx25pdk/imximage.cfg
create mode 100644 board/freescale/mx25pdk/lowlevel_init.S
create mode 100644 board/freescale/mx25pdk/mx25pdk.c
create mode 100644 include/configs/mx25pdk.h
delete mode 100644 nand_spl/board/freescale/mx31pdk/config.mk
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
next reply other threads:[~2011-09-26 11:35 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-09-26 11:35 Stefano Babic [this message]
2011-09-27 7:01 ` [U-Boot] Please pull u-boot-imx/next into arm/next Albert ARIBAUD
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E806377.70701@denx.de \
--to=sbabic@denx.de \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.