[PATCH 4/4] arm/imx: fix imx6q mmc error when mounting rootfs

[dirk.behme@de.bosch.com (Dirk Behme)]

On 10.11.2011 09:39, Shawn Guo wrote:
> The following error is seen in some case when mounting rootfs from
> SD/MMC cards.
> 
>   Waiting for root device /dev/mmcblk0p1...
>   mmc1: host does not support reading read-only switch. assuming write-enable.
>   mmc1: new high speed SDHC card at address b368
>   mmcblk0: mmc1:b368 SDC   3.74 GiB
>    mmcblk0: p1
>   mmc1: Timeout waiting for hardware interrupt.
>   mmcblk0: error -110 transferring data, sector 3678224, nr 40, cmd response 0x900, card status 0xc00
>   end_request: I/O error, dev mmcblk0, sector 3678225
>   Buffer I/O error on device mmcblk0p1, logical block 458754
>   lost page write due to I/O error on mmcblk0p1
> 
> This patch fixes the problem by lowering the usdhc clock and correcting
> watermark configuration.
> 
> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
> Cc: Chris Ball <cjb@laptop.org>
> Cc: Sascha Hauer <s.hauer@pengutronix.de>

The above errors are gone with this patch.

Tested-by: Dirk Behme <dirk.behme@de.bosch.com>

Thanks

Dirk

> ---
>  arch/arm/mach-imx/clock-imx6q.c    |   17 ++++++++++++++++-
>  drivers/mmc/host/sdhci-esdhc-imx.c |    8 ++++++++
>  2 files changed, 24 insertions(+), 1 deletions(-)
> 
> diff --git a/arch/arm/mach-imx/clock-imx6q.c b/arch/arm/mach-imx/clock-imx6q.c
> index e0b926d..613a1b9 100644
> --- a/arch/arm/mach-imx/clock-imx6q.c
> +++ b/arch/arm/mach-imx/clock-imx6q.c
> @@ -1139,7 +1139,7 @@ static int _clk_set_rate(struct clk *clk, unsigned long rate)
>  		return -EINVAL;
>  
>  	max_div = ((d->bm_pred >> d->bp_pred) + 1) *
> -		  ((d->bm_pred >> d->bp_pred) + 1);
> +		  ((d->bm_podf >> d->bp_podf) + 1);
>  
>  	div = parent_rate / rate;
>  	if (div == 0)
> @@ -2002,6 +2002,21 @@ int __init mx6q_clocks_init(void)
>  	clk_set_rate(&asrc_serial_clk, 1500000);
>  	clk_set_rate(&enfc_clk, 11000000);
>  
> +	/*
> +	 * Before pinctrl API is available, we have to rely on the pad
> +	 * configuration set up by bootloader.  For usdhc example here,
> +	 * u-boot sets up the pads for 49.5 MHz case, and we have to lower
> +	 * the usdhc clock from 198 to 49.5 MHz to match the pad configuration.
> +	 *
> +	 * FIXME: This is should be removed after pinctrl API is available.
> +	 * At that time, usdhc driver can call pinctrl API to change pad
> +	 * configuration dynamically per different usdhc clock settings.
> +	 */
> +	clk_set_rate(&usdhc1_clk, 49500000);
> +	clk_set_rate(&usdhc2_clk, 49500000);
> +	clk_set_rate(&usdhc3_clk, 49500000);
> +	clk_set_rate(&usdhc4_clk, 49500000);
> +
>  	np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-gpt");
>  	base = of_iomap(np, 0);
>  	WARN_ON(!base);
> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
> index ae57769..4b976f0 100644
> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> @@ -32,6 +32,7 @@
>  /* VENDOR SPEC register */
>  #define SDHCI_VENDOR_SPEC		0xC0
>  #define  SDHCI_VENDOR_SPEC_SDIO_QUIRK	0x00000002
> +#define SDHCI_WTMK_LVL			0x44
>  #define SDHCI_MIX_CTRL			0x48
>  
>  /*
> @@ -476,6 +477,13 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev)
>  	if (is_imx53_esdhc(imx_data))
>  		imx_data->flags |= ESDHC_FLAG_MULTIBLK_NO_INT;
>  
> +	/*
> +	 * The imx6q ROM code will change the default watermark level setting
> +	 * to something insane.  Change it back here.
> +	 */
> +	if (is_imx6q_usdhc(imx_data))
> +		writel(0x08100810, host->ioaddr + SDHCI_WTMK_LVL);
> +
>  	boarddata = &imx_data->boarddata;
>  	if (sdhci_esdhc_imx_probe_dt(pdev, boarddata) < 0) {
>  		if (!host->mmc->parent->platform_data) {