From: Joseph Salisbury <joseph.salisbury@canonical.com>
To: Treeve Jelbert <treeve@scarlet.be>
Cc: linux-kernel@vger.kernel.org
Subject: Re: PROBLEM: Radeon display connector : No monitor connected or invalid EDID
Date: Wed, 23 Nov 2011 15:37:07 -0500 [thread overview]
Message-ID: <4ECD5973.7080605@canonical.com> (raw)
In-Reply-To: <2407026.akcTO2Ggic@gemini-64>
On 11/13/2011 12:27 PM, Treeve Jelbert wrote:
> PROBLEM: Radeon display connector : No monitor connected or invalid EDID
> ​
> Since installing kernel-3.1.1 the screen goes blank during the boot and I am
> unable to do anything, not even ssh into the box.
> ​
> linux-3.1.0 worked ok. There are no other changes to the system. Both were
> built using the same config file.
> ​
> When I reboot into 3.1.0 and check the log messages, I see
> ​
> Nov 13 14:31:22 Edge-64 kernel: [ 0.055378] CPU0: AMD A6-3400M APU with
> Radeon(tm) HD Graphics stepping 00
> ​
> # grep '\[drm\]' messages |cut -d: -f4-
> [ 0.645028] [drm] Initialized drm 1.1.0 20060810
> [ 14.128321] [drm] radeon defaulting to kernel modesetting.
> [ 14.128391] [drm] radeon kernel modesetting enabled.
> [ 14.129217] [drm] initializing kernel modesetting (SUMO 0x1002:0x9647
> 0x17AA:0x21EA).
> [ 14.129410] [drm] register mmio base: 0xF0B00000
> [ 14.129476] [drm] register mmio size: 262144
> [ 14.130388] [drm] Detected VRAM RAM=512M, BAR=256M
> [ 14.130459] [drm] RAM width 32bits DDR
> [ 14.130848] [drm] radeon: 512M of VRAM memory ready
> [ 14.130912] [drm] radeon: 512M of GTT memory ready.
> [ 14.131021] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
> [ 14.131085] [drm] Driver supports precise vblank timestamp query.
> [ 14.131281] [drm] radeon: irq initialized.
> [ 14.131347] [drm] GART: num cpu pages 131072, num gpu pages 131072
> [ 14.132538] [drm] Loading SUMO Microcode
> [ 14.547990] [drm] ring test succeeded in 1 usecs
> [ 14.548128] [drm] radeon: ib pool ready.
> [ 14.548249] [drm] ib test succeeded in 0 usecs
> [ 14.551990] [drm] Radeon Display Connectors
> [ 14.552056] [drm] Connector 0:
> [ 14.552119] [drm] VGA
> [ 14.552179] [drm] HPD2
> [ 14.552242] [drm] DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448
> 0x644c 0x644c
> [ 14.552336] [drm] Encoders:
> [ 14.552397] [drm] CRT1: INTERNAL_UNIPHY2
> [ 14.552473] [drm] CRT1: NUTMEG
> [ 14.552535] [drm] Connector 1:
> [ 14.552596] [drm] LVDS
> [ 14.552657] [drm] HPD1
> [ 14.552718] [drm] DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438
> 0x643c 0x643c
> [ 14.552809] [drm] Encoders:
> [ 14.552870] [drm] LCD1: INTERNAL_UNIPHY2
> [ 14.552932] [drm] LCD1: TRAVIS
> [ 14.552994] [drm] Connector 2:
> [ 14.553055] [drm] HDMI-A
> [ 14.553115] [drm] HPD3
> [ 14.553176] [drm] DDC: 0x6450 0x6450 0x6454 0x6454 0x6458 0x6458
> 0x645c 0x645c
> [ 14.553266] [drm] Encoders:
> [ 14.553327] [drm] DFP1: INTERNAL_UNIPHY
> [ 14.952397] [drm] Radeon display connector VGA-1: No monitor connected or
> invalid EDID
> [ 15.352332] [drm] Radeon display connector LVDS-1: No monitor connected or
> invalid EDID
> [ 15.752357] [drm] Radeon display connector HDMI-A-1: No monitor connected
> or invalid EDID
> [ 15.779878] [drm] Internal thermal controller without fan control
> [ 15.780236] [drm] radeon: power management initialized
> [ 16.014394] [drm] fb mappable at 0xE0141000
> [ 16.014506] [drm] vram apper at 0xE0000000
> [ 16.014568] [drm] size 4325376
> [ 16.014629] [drm] fb depth is 24
> [ 16.014690] [drm] pitch is 5632
> [ 16.111788] [drm] Initialized radeon 2.11.0 20080528 for 0000:00:01.0 on
> minor 0
> ​
> at this point the log ends.
> ​
> ​
> I also see
> ​
> [ 13.411889] thinkpad_acpi: Lenovo ThinkPad E525, model 12002JG
> [ 14.129616] ATOM BIOS: Lenovo
> ​
> Those messages did not appear in 3.1.0
> I am not sure of the meaning of ATOM, but I have an AMD system, not Intel.
> ​
> ​
> Keywords:graphics drm radeon Lenovo
> ​
> The following data is from the running linux-3.1.0
> $ lspci -vvv
> ​
> ​
> 00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 12h Processor Root
> Complex
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 64
> ​
> 00:01.0 VGA compatible controller: ATI Technologies Inc Device 9647 (prog-if
> 00 [VGA controller])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
> Region 1: I/O ports at 4000 [size=256]
> Region 2: Memory at f0b00000 (32-bit, non-prefetchable) [size=256K]
> Expansion ROM at<unassigned> [disabled]
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI
> 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <4us, L1
> unlimited
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #0, Speed unknown, Width x0, ASPM
> unknown, Latency L0
> <64ns, L1<1us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed unknown, Width x0, TrErr- Train-
> SlotClk- DLActive-
> BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel modules: radeon
> ​
> 00:01.1 Audio device: ATI Technologies Inc Device 1714
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 46
> Region 0: Memory at f0b44000 (32-bit, non-prefetchable) [size=16K]
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI
> 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <4us, L1
> unlimited
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #0, Speed unknown, Width x0, ASPM
> unknown, Latency L0
> <64ns, L1<1us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed unknown, Width x0, TrErr- Train-
> SlotClk- DLActive-
> BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4181
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: snd_hda_intel
> ​
> 00:04.0 PCI bridge: Advanced Micro Devices [AMD] Family 12h Processor Root
> Port (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 00003000-00003fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort-<SERR-<PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort->Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1<1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <64ns, L1<1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
> CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive+
> BWMgmt- ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
> HotPlug- Surprise-
> Slot #4, PowerLimit 75.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
> CmdCplt- HPIrq-
> LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power-
> Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
> PresDet+ Interlock-
> Changed: MRL- PresDet+ LinkState+
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis+,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4141
> Capabilities: [b0] Subsystem: Lenovo Device 21ea
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:11.0 SATA controller: Advanced Micro Devices [AMD] Hudson SATA Controller
> [AHCI mode] (prog-if 01 [AHCI 1.0])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64
> Interrupt: pin A routed to IRQ 45
> Region 0: I/O ports at 4118 [size=8]
> Region 1: I/O ports at 4124 [size=4]
> Region 2: I/O ports at 4110 [size=8]
> Region 3: I/O ports at 4120 [size=4]
> Region 4: I/O ports at 4100 [size=16]
> Region 5: Memory at f0b4b000 (32-bit, non-prefetchable) [size=2K]
> Capabilities: [50] MSI: Enable+ Count=1/16 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4171
> Capabilities: [70] SATA HBA v1.0 InCfgSpace
> Kernel driver in use: ahci
> ​
> 00:12.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI
> Controller (rev 11) (prog-if 10 [OHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at f0b4a000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci_hcd
> Kernel modules: ohci-hcd
> ​
> 00:12.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI
> Controller (rev 11) (prog-if 20 [EHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 17
> Region 0: Memory at f0b4bb00 (32-bit, non-prefetchable) [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [e4] Debug port: BAR=1 offset=00e0
> Kernel driver in use: ehci_hcd
> ​
> 00:13.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI
> Controller (rev 11) (prog-if 10 [OHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at f0b49000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci_hcd
> Kernel modules: ohci-hcd
> ​
> 00:13.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI
> Controller (rev 11) (prog-if 20 [EHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 17
> Region 0: Memory at f0b4ba00 (32-bit, non-prefetchable) [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [e4] Debug port: BAR=1 offset=00e0
> Kernel driver in use: ehci_hcd
> ​
> 00:14.0 SMBus: Advanced Micro Devices [AMD] Hudson SMBus Controller (rev 13)
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:14.2 Audio device: Advanced Micro Devices [AMD] Hudson Azalia Controller
> (rev 01)
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at f0b40000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Kernel driver in use: snd_hda_intel
> ​
> 00:14.3 ISA bridge: Advanced Micro Devices [AMD] Hudson LPC Bridge (rev 11)
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0
> ​
> 00:14.4 PCI bridge: Advanced Micro Devices [AMD] Hudson PCI Bridge (rev 40)
> (prog-if 01 [Subtractive decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: fff00000-000fffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-
> <MAbort+<SERR-<PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort->Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> ​
> 00:14.7 SD Host controller: Advanced Micro Devices [AMD] Hudson SD Flash
> Controller (prog-if 01)
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 71, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at f0b4b900 (32-bit, non-prefetchable) [size=256]
> Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Kernel driver in use: sdhci-pci
> Kernel modules: sdhci-pci
> ​
> 00:15.0 PCI bridge: Advanced Micro Devices [AMD] Device 43a0 (prog-if 00
> [Normal decode])
> Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort-<SERR-<PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort->Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1<1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #247, Speed 5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <64ns, L1<1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed unknown, Width x16, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
> Selectable De-emphasis: -3.5dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4149
> Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:15.1 PCI bridge: Advanced Micro Devices [AMD] Device 43a1 (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: f0a00000-f0afffff
> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort+<SERR-<PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort->Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1<1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1,
> Latency L0<64ns,
> L1<1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
> CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive+
> BWMgmt- ABWMgmt-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
> Selectable De-emphasis: -3.5dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4151
> Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:15.2 PCI bridge: Advanced Micro Devices [AMD] Device 43a2 (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
> I/O behind bridge: 00002000-00002fff
> Memory behind bridge: f0900000-f09fffff
> Prefetchable memory behind bridge: 00000000f0c00000-00000000f0dfffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort-<SERR-<PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort->Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1<1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1,
> Latency L0<64ns,
> L1<1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive+
> BWMgmt- ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
> HotPlug+ Surprise-
> Slot #0, PowerLimit 0.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
> CmdCplt- HPIrq-
> LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power-
> Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
> PresDet+ Interlock-
> Changed: MRL- PresDet- LinkState+
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
> Selectable De-emphasis: -3.5dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4159
> Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:15.3 PCI bridge: Advanced Micro Devices [AMD] Device 43a3 (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=06, subordinate=07, sec-latency=0
> I/O behind bridge: 00001000-00001fff
> Memory behind bridge: f0500000-f08fffff
> Prefetchable memory behind bridge: 00000000f0100000-00000000f04fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort-<SERR-<PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort->Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1<1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #247, Speed 5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <64ns, L1<1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed unknown, Width x16, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
> HotPlug+ Surprise-
> Slot #0, PowerLimit 0.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
> CmdCplt- HPIrq-
> LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power-
> Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
> PresDet- Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
> Selectable De-emphasis: -3.5dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4161
> Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:16.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI
> Controller (rev 11) (prog-if 10 [OHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at f0b48000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci_hcd
> Kernel modules: ohci-hcd
> ​
> 00:16.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI
> Controller (rev 11) (prog-if 20 [EHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 17
> Region 0: Memory at f0b4b800 (32-bit, non-prefetchable) [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [e4] Debug port: BAR=1 offset=00e0
> Kernel driver in use: ehci_hcd
> ​
> 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 0 (rev 43)
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 1
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 2
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 3
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Capabilities: [f0] Secure device<?>
> Kernel driver in use: k10temp
> ​
> 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 4
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 6
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 5
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 7
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI
> Express Gigabit Ethernet controller (rev 06)
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 47
> Region 0: I/O ports at 3000 [size=256]
> Region 2: Memory at f0004000 (64-bit, prefetchable) [size=4K]
> Region 4: Memory at f0000000 (64-bit, prefetchable) [size=16K]
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4189
> Capabilities: [70] Express (v2) Endpoint, MSI 01
> DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
> <512ns, L1<64us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 128 bytes, MaxReadReq 4096 bytes
> DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+
> AuxPwr+ TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <512ns, L1<64us
> ClockPM+ Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
> CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis+
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
> Vector table: BAR=4 offset=00000000
> PBA: BAR=4 offset=00000800
> Capabilities: [d0] Vital Product Data
> Unknown small resource type 00, will not decode more.
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq+ ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF+
> MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr+
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr-
> AERCap: First Error Pointer: 14, GenCap+ CGenEn-
> ChkCap+ ChkEn-
> Capabilities: [140 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> Status: NegoPending- InProgress-
> Capabilities: [160 v1] Device Serial Number 3a-0b-00-00-68-4c-e0-00
> Kernel driver in use: r8169
> Kernel modules: r8169
> ​
> 04:00.0 System peripheral: Ricoh Co Ltd Device e823 (rev 04) (prog-if 01)
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 17
> Region 0: Memory at f0a00200 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [78] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
> Capabilities: [80] Express (v1) Endpoint, MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> unlimited, L1
> unlimited
> ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+
> AuxPwr- TransPend-
> LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0<4us,
> L1 unlimited
> ClockPM+ Surprise- LLActRep- BwNot-
> LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> Capabilities: [100 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> Status: NegoPending- InProgress-
> Capabilities: [800 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF+
> MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr+
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr+
> AERCap: First Error Pointer: 00, GenCap+ CGenEn-
> ChkCap+ ChkEn-
> Kernel driver in use: sdhci-pci
> Kernel modules: sdhci-pci
> ​
> 05:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE
> 802.11b/g/n WiFi Adapter (rev 01)
> Subsystem: Realtek Semiconductor Co., Ltd. Device 8195
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: I/O ports at 2000 [size=256]
> Region 2: Memory at f0900000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [70] Express (v2) Endpoint, MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <512ns, L1<64us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr+ TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <512ns, L1<64us
> ClockPM+ Surprise- LLActRep- BwNot-
> LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk+
> ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis+
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis+
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF+
> MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr+
> AERCap: First Error Pointer: 00, GenCap+ CGenEn-
> ChkCap+ ChkEn-
> Capabilities: [140 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> Status: NegoPending- InProgress-
> Capabilities: [160 v1] Device Serial Number 01-91-81-fe-ff-4c-e0-00
> Kernel driver in use: rtl8192ce
> Kernel modules: rtl8192ce
> ​
> ​
> ​
> ​
> ​
> $ lsmod
> Module Size Used by
> rtl8192ce 69655 0
> rtl8192c_common 54535 1 rtl8192ce
> cfbcopyarea 3217 0
> ohci_hcd 20690 0
> sdhci_pci 8440 0
> rtlwifi 87860 1 rtl8192ce
> sdhci 21347 1 sdhci_pci
> cfbimgblt 1969 0
> mmc_core 67307 1 sdhci
> r8169 43238 0
> cfbfillrect 3581 0
> processor 22993 4
> mii 3707 1 r8169
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
Hi Treeve,
Have you ever tested the 3.0 kernel on this machine? There is a similar
issue reported[1] for a system equipped with an AMD APU, but that issue
happens on a 3.0.6 kernel.
Thanks,
Joe
[1] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/891968
next prev parent reply other threads:[~2011-11-23 20:37 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-11-13 17:27 PROBLEM: Radeon display connector : No monitor connected or invalid EDID Treeve Jelbert
2011-11-13 18:47 ` Dave Airlie
2011-11-13 20:36 ` Alex Deucher
2011-11-23 20:37 ` Joseph Salisbury [this message]
2011-11-23 22:26 ` Treeve Jelbert
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4ECD5973.7080605@canonical.com \
--to=joseph.salisbury@canonical.com \
--cc=linux-kernel@vger.kernel.org \
--cc=treeve@scarlet.be \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.