From: Fil <lists@internyc.net>
To: christophe.varoqui@opensvc.com,
device-mapper development <dm-devel@redhat.com>
Subject: Re: mpathpersist
Date: Sat, 31 Dec 2011 12:52:49 -0500 [thread overview]
Message-ID: <4EFF4BF1.2070608@internyc.net> (raw)
In-Reply-To: <1325340015.6564.18.camel@lapoo.opensvc.com>
oops sorry, I was reading something else you responded to so
automatically I wrote to you....
thanks
fil
On 12/31/2011 09:00 AM, Christophe Varoqui wrote:
>
>> I have seen your set of patches for persistent reservation of multipath
>> devices and wanted to try them out. While trying this patch set I have
>> run into several issues. Which code base can I apply this against? Any
>> help would be greatly appreciated. Issues are listed below.
>
> This patchset has been developped by Netapp's Vijay Chauhan.
>
>> 2. I pulled multipath-tools from opensvc git and that patching failed
>> too, so I had to apply all the patches manually.
>>
> This is the correct project repository. The patchset may need rebasing
> over the HEAD. If it does not apply cleanly there, you might try to
> revert to a previous commit.
>
> I'll try this patchset soon and compare my experience with your
> observations.
>
> Thanks for the report.
>
>> 3. while testing mppersist I get following error:
>>
>> mpathpersist --out --register --param-sark=123abc --prout-type=8
>> /dev/mapper/blah -v 4
>> Dec 31 00:54:29 | alias = blah
>> Dec 31 00:54:29 | params = 0 0 1 1 round-robin 0 2 1 8:0 1 8:16 1
>> Dec 31 00:54:29 | status = 2 0 0 0 1 1 A 0 2 0 8:0 A 0 8:16 A 0
>> Dec 31 00:54:29 | blah: disassemble map [0 0 1 1 round-robin 0 2 1 8:0 1
>> 8:16 1 ]
>> Dec 31 00:54:29 | 8:0: not found in pathvec
>> Dec 31 00:54:29 | 8:16: not found in pathvec
>> Dec 31 00:54:29 | No device found for 8:0
>>
>> Dec 31 00:54:29 | No device found for 8:16
>>
>> Dec 31 00:54:29 | blah: disassemble status [2 0 0 0 1 1 A 0 2 0 8:0 A 0
>> 8:16 A 0 ]
>> Dec 31 00:54:29 | 36001405c55fc03cd8193d491eda0d4d7: no path available
>> PR out: command failed
>>
>> 4. with all patches applied, all multipathd cli commands crash the daemon.
>>
>> here are my configs:
>>
>> cat /etc/multipath.conf
>> defaults {
>> user_friendly_names yes
>> polling_interval 10
>> }
>>
>> multipaths {
>> multipath {
>> wwid 36001405c55fc03cd8193d491eda0d4d7
>> alias blah
>> }
>> }
>>
>>
>> devices {
>> device {
>> vendor "QNAP"
>> product "iSCSI Storage"
>> path_selector "round-robin 0"
>> path_grouping_policy multibus
>> getuid_callout "/lib/udev/scsi_id -g -u -d /dev/%n"
>> path_checker directio
>> failback immediate
>> }
>>
>> }
>>
>> blacklist {
>> devnode "^(vd)[a-z]"
>> }
>>
>> multipath -ll -v3
>> Dec 31 00:59:01 | loading /lib64/multipath/libcheckdirectio.so checker
>> Dec 31 00:59:01 | loading /lib64/multipath/libprioconst.so prioritizer
>> Dec 31 00:59:01 | loop0: device node name blacklisted
>> Dec 31 00:59:01 | loop1: device node name blacklisted
>> Dec 31 00:59:01 | loop2: device node name blacklisted
>> Dec 31 00:59:01 | loop3: device node name blacklisted
>> Dec 31 00:59:01 | loop4: device node name blacklisted
>> Dec 31 00:59:01 | loop5: device node name blacklisted
>> Dec 31 00:59:01 | loop6: device node name blacklisted
>> Dec 31 00:59:01 | loop7: device node name blacklisted
>> Dec 31 00:59:01 | vda: device node name blacklisted
>> Dec 31 00:59:01 | dm-0: device node name blacklisted
>> Dec 31 00:59:01 | dm-1: device node name blacklisted
>> Dec 31 00:59:01 | dm-2: device node name blacklisted
>> Dec 31 00:59:01 | dm-3: device node name blacklisted
>> Dec 31 00:59:01 | sda: not found in pathvec
>> Dec 31 00:59:01 | sda: mask = 0x5
>> Dec 31 00:59:01 | sda: dev_t = 8:0
>> Dec 31 00:59:01 | sda: size = 20971520
>> Dec 31 00:59:01 | sda: vendor = QNAP
>> Dec 31 00:59:01 | sda: product = iSCSI Storage
>> Dec 31 00:59:01 | sda: rev = 3.1
>> Dec 31 00:59:01 | sda: h:b:t:l = 2:0:0:0
>> Dec 31 00:59:01 | sda: path state = running
>> Dec 31 00:59:01 | sda: get_state
>> Dec 31 00:59:01 | sda: path checker = directio (controller setting)
>> Dec 31 00:59:01 | sda: checker timeout = 30000 ms (sysfs setting)
>> Dec 31 00:59:01 | directio: starting new request
>> Dec 31 00:59:01 | directio: io finished 4096/0
>> Dec 31 00:59:01 | sda: state = up
>> Dec 31 00:59:01 | sdb: not found in pathvec
>> Dec 31 00:59:01 | sdb: mask = 0x5
>> Dec 31 00:59:01 | sdb: dev_t = 8:16
>> Dec 31 00:59:01 | sdb: size = 20971520
>> Dec 31 00:59:01 | sdb: vendor = QNAP
>> Dec 31 00:59:01 | sdb: product = iSCSI Storage
>> Dec 31 00:59:01 | sdb: rev = 3.1
>> Dec 31 00:59:01 | sdb: h:b:t:l = 3:0:0:0
>> Dec 31 00:59:01 | sdb: path state = running
>> Dec 31 00:59:01 | sdb: get_state
>> Dec 31 00:59:01 | sdb: path checker = directio (controller setting)
>> Dec 31 00:59:01 | sdb: checker timeout = 30000 ms (sysfs setting)
>> Dec 31 00:59:01 | directio: starting new request
>> Dec 31 00:59:01 | directio: io finished 4096/0
>> Dec 31 00:59:01 | sdb: state = up
>> Dec 31 00:59:01 | dm-4: device node name blacklisted
>> ===== paths list =====
>> uuid hcil dev dev_t pri dm_st chk_st vend/prod/rev dev_st
>> 2:0:0:0 sda 8:0 -1 undef ready QNAP,iSCSI Storage running
>> 3:0:0:0 sdb 8:16 -1 undef ready QNAP,iSCSI Storage running
>> Dec 31 00:59:01 | params = 0 0 1 1 round-robin 0 2 1 8:0 1 8:16 1
>> Dec 31 00:59:01 | status = 2 0 0 0 1 1 A 0 2 0 8:0 A 0 8:16 A 0
>> Dec 31 00:59:01 | blah: disassemble map [0 0 1 1 round-robin 0 2 1 8:0 1
>> 8:16 1 ]
>> Dec 31 00:59:01 | sda: mask = 0x8
>> Dec 31 00:59:01 | sda: path state = running
>> Dec 31 00:59:01 | sda: prio = const (internal default)
>> Dec 31 00:59:01 | sda: prio = (internal default)
>> Dec 31 00:59:01 | sda: const prio = 1
>> Dec 31 00:59:01 | sdb: mask = 0x8
>> Dec 31 00:59:01 | sdb: path state = running
>> Dec 31 00:59:01 | sdb: prio = const (internal default)
>> Dec 31 00:59:01 | sdb: prio = (internal default)
>> Dec 31 00:59:01 | sdb: const prio = 1
>> Dec 31 00:59:01 | blah: disassemble status [2 0 0 0 1 1 A 0 2 0 8:0 A 0
>> 8:16 A 0 ]
>> blah (36001405c55fc03cd8193d491eda0d4d7) dm-4 QNAP,iSCSI Storage
>> size=10G features='0' hwhandler='0' wp=rw
>> `-+- policy='round-robin 0' prio=0 status=active
>> |- 2:0:0:0 sda 8:0 active ready running
>> `- 3:0:0:0 sdb 8:16 active ready running
>> Dec 31 00:59:01 | directio checker refcount 2
>> Dec 31 00:59:01 | directio checker refcount 1
>> Dec 31 00:59:01 | unloading const prioritizer
>> Dec 31 00:59:01 | unloading directio checker
>>
>> --
>> dm-devel mailing list
>> dm-devel@redhat.com
>> https://www.redhat.com/mailman/listinfo/dm-devel
>
>
>
> --
> dm-devel mailing list
> dm-devel@redhat.com
> https://www.redhat.com/mailman/listinfo/dm-devel
next prev parent reply other threads:[~2011-12-31 17:52 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-12-31 6:05 mpathpersist Fil
2011-12-31 14:00 ` mpathpersist Christophe Varoqui
2011-12-31 17:52 ` Fil [this message]
2012-01-02 11:53 ` mpathpersist Chauhan, Vijay
2012-01-03 3:32 ` mpathpersist Fil
2012-01-04 11:42 ` mpathpersist Chauhan, Vijay
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4EFF4BF1.2070608@internyc.net \
--to=lists@internyc.net \
--cc=christophe.varoqui@opensvc.com \
--cc=dm-devel@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.