Re: Bug report - patch_realtek.c - Laptop HP COMPAQ B1900 Series

["joey.jiaojg" <joey.jiaojg@gmail.com>]

Please check my reply below.

On 2012年02月15日 18:11, Takashi Iwai wrote:
> At Wed, 15 Feb 2012 18:06:39 +0800,
> joey.jiaojg wrote:
>> OK, the situation is 0x01 is to control GPIO0:
>> 1. if I write (codec,0x01,0,AC_VERB_SET_GPIO_MASK,1) only; the result is
>> speaker not work.
>>
>> 2. if I write (codec,0x01,0,AC_VERB_SET_GPIO_DIRECTION,1) only; the
>> result is speaker not work.
>>
> Sure, GPIO must be always set mask, direction and data all together.
> The question is, when you set GPIO mask/dir/data, the speaker starts
> playing, and if set to zero (e.g. only data), the speaker is muted?
JOEY: I tried set data to 0 or 1 doesn't influence. when I set mask & 
dir to 1, speaker starts to work and to 0 speaker muted while headphone 
works if headphone plugged in.
>
>> 3. If I write step 1&  2 together, speaker works when I reboot.
> Then GPIO is likely an external amp control.
JOEY: YES.
>
>> 4. Then If I plugged in the headphone, the headphone doesn't work. It
>> only works when I write
>> (codec,0x0F,0,AC_VERB_SET_PIN_WIDGET_CONTROL,PIN_HP).
> This is normal.
JOEY: If I don't modify model=will. And headphone can play even without 
set AC_VERB_SET_PIN_WIDGET_CONTROL to PIN_HP. Of course, automute 
doesn't work as there is function implemented.
>
>> 5. From step 3&  4, it's similar for cases that I reboot with headphone
>> plugged in. That is, if I remove headphone, speaker doesn't work
>> automatically. If I write
>> (codec,0x0F,0,AC_VERB_SET_PIN_WIDGET_CONTROL,PIN_OUT), the
>> auto-detection function works well can switch speaker/headphone
>> automatically.
> That's odd.  If you don't change from PIN_HP, doesn't the unsolicited
> event work?
JOEY: the unsolicited works from the register I read also from the 
printk I previous added. But the audio path doesn't switch between 
speaker and headphone. I don't know why. It can works manually if I send 
any hda-verb command to codec, like hda-verb /dev/snd/hwC0D0 0x0F 0xF09 
0x0; I think perhaps there needs to be some delay. But I wait seconds 
and it doesn't switch. Then if I run any hda-verb command, it will then 
switch.
Then after I change from PIN_HP or from PIN_OUT, the automute (actually 
audio path switch) works.
> Another question is, when you set PIN_WIDGET_CONTROL on the speaker
> pin (not sure which one is) to 0x00, does it mute the speaker, too?
JOEY: No, it doesn't mute the speaker. To mute the speaker, I just need 
to set 0 to dir or mask. Then audio path is to headphone.
>
> Takashi
>
>
>> I don't know why it's this case, and from alsa document, it seems only
>> enable GPIO0 will work but actually not.
>>
>>
>> On 2012年02月15日 17:58, Takashi Iwai wrote:
>>> At Wed, 15 Feb 2012 17:45:37 +0800,
>>> joey.jiaojg wrote:
>>>> I have tried to enable each one of them separately, and the speaker
>>>> doesn't work.
>>> Sorry, it's not clear what you meant.  Each of what separately?
>>> And what does GPIO do exactly?
>>>
>>>> I have to use these 3 write_cache to make switch and auto-detect work
>>>> smoothly.
>>> We need to know the reason why these must be needed.
>>>
>>>
>>> Takashi
>>>
>>>
>>>> On 2012年02月15日 17:40, Takashi Iwai wrote:
>>>>> At Wed, 15 Feb 2012 17:31:44 +0800,
>>>>> joey.jiaojg wrote:
>>>>>> Here is the diff file.
>>>>> Thanks.
>>>>>
>>>>>> +/* toggle speaker-output according to the hp-jack state */
>>>>>> +static void alc260_b1900_automute(struct hda_codec *codec)
>>>>>> +{
>>>>>> +        unsigned int present;
>>>>>> +
>>>>>> +	present = snd_hda_jack_detect(codec, 0x0f);
>>>>>> +	if (present) {
>>>>>> +		snd_hda_codec_write_cache(codec, 0x01, 0,
>>>>>> +					  AC_VERB_SET_GPIO_MASK, 0);
>>>>>> +		snd_hda_codec_write_cache(codec, 0x01, 0,
>>>>>> +					  AC_VERB_SET_GPIO_DIRECTION,
>>>>>> +					  0);
>>>>> What actually this GPIO bit does on your device?
>>>>> To mute/unmute the speaker?
>>>>>
>>>>> If so, doesn't the speaker toggle work with just changing the
>>>>> pin-control of the corresponding pin?
>>>>>
>>>>>
>>>>> Takashi

_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel