From: Bob Ciotti <Bob.Ciotti-NSQ8wuThN14@public.gmane.org>
To: Hal Rosenstock <hal-LDSdmyG8hGV8YrgS2mwiifqBs+8SCbDb@public.gmane.org>
Cc: "linux-rdma-u79uwXL29TY76Z2rM5mHXA@public.gmane.org"
<linux-rdma-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>
Subject: Re: watchdog timer
Date: Fri, 18 May 2012 07:35:28 -0700 [thread overview]
Message-ID: <4FB65E30.4070805@nasa.gov> (raw)
In-Reply-To: <4FB649A6.2060602-LDSdmyG8hGV8YrgS2mwiifqBs+8SCbDb@public.gmane.org>
On 05/18/2012 06:07 AM, Hal Rosenstock wrote:
> On 5/18/2012 2:05 AM, Bob Ciotti wrote:
>>
>>
>> I'm seeing lots of these messages in SM log:
>>
>> May 17 22:36:04 947774 [DA234710] 0x01 -> log_trap_info: Received
>> Generic Notice type:1 num:131 (Flow Control Update watchdog timer
>> expired) Producer:2 (Switch) from LID:444 Port 5 TID:0x0000000000000025
>>
>> the referenced port is a switch to HCA link.
>>
>> I've seen this in cases where there was bad hardware. Spec says failure
>> in flow control machine on other end. But lets assume hardware was good.
>> When could this occur?
>
> Do OperationalVLs match on both sides of the link ? Are you
> using/configuring QoS ?
>
There are two separate fabric on each port of 2 port HCA.
Issue is seen on both fabrics.
Normally we use QoS on both fabrics. QoS now disabled on
ib0 on hca port 1:
r327i7n0 ~ # smpquery portinfo 248 | grep VL
VLCap:...........................VL0-7
VLHighLimit:.....................4
VLArbHighCap:....................8
VLArbLowCap:.....................8
VLStallCount:....................0
OperVLs:.........................VL0-7
r327i7n0 ~ # smpquery -D portinfo 0 1 | grep VL
VLCap:...........................VL0-7
VLHighLimit:.....................4
VLArbHighCap:....................8
VLArbLowCap:.....................8
VLStallCount:....................0
OperVLs:.........................VL0-7
r327i7n0 ~ # smpquery -D portinfo 0,1 1 | grep VL
VLCap:...........................VL0-7
VLHighLimit:.....................4
VLArbHighCap:....................8
VLArbLowCap:.....................8
VLStallCount:....................7
OperVLs:.........................VL0-7
r327i7n0 ~ # ibstat
CA 'mlx4_0'
CA type: MT4099
Number of ports: 2
Firmware version: 2.10.4350
Hardware version: 0
Node GUID: 0x0002c90300336b20
System image GUID: 0x0002c90300336b23
Port 1:
State: Active
Physical state: LinkUp
Rate: 56
Base lid: 248
LMC: 0
SM lid: 1
Capability mask: 0x02514868
Port GUID: 0x0002c90300336b21
Link layer: InfiniBand
Port 2:
State: Active
Physical state: LinkUp
Rate: 56
Base lid: 1971
LMC: 0
SM lid: 1685
Capability mask: 0x02514868
Port GUID: 0x0002c90300336b22
Link layer: InfiniBand
r327i7n0 ~ # smpquery -D nodeinfo 0,1 1
# Node info: DR path slid 65535; dlid 65535; 0,1
BaseVers:........................1
ClassVers:.......................1
NodeType:........................Switch
NumPorts:........................36
SystemGuid:......................0x080069000000a4db
Guid:............................0x080069000000a4d8
PortGuid:........................0x080069000000a4d8
PartCap:.........................8
DevId:...........................0xc738
Revision:........................0x000000a1
LocalPort:.......................1
VendorId:........................0x0002c9
r327i7n0 ~ # smpquery -D nodedesc 0,1
Node Description:.SwitchX - Mellanox Technologies
r327i7n0 ~ # smpquery -D sl2vl 0,1 1
# SL2VL table: DR path slid 65535; dlid 65535; 0,1
# SL: | 0| 1| 2| 3| 4| 5| 6| 7| 8| 9|10|11|12|13|14|15|
ports: in 0, out 1: | 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0|
ports: in 1, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 2, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 3, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 4, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 5, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 6, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 7, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 8, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 9, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 10, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 11, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 12, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 13, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 14, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 15, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 16, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 17, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 18, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 19, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 20, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 21, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 22, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 23, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 24, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 25, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 26, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 27, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 28, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 29, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 30, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 31, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 32, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 33, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 34, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 35, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
ports: in 36, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 0| 1| 2| 3| 4| 5| 6| 7|
r327i7n0 ~ # smpquery -D sl2vl 0 1
# SL2VL table: DR path slid 65535; dlid 65535; 0
# SL: | 0| 1| 2| 3| 4| 5| 6| 7| 8| 9|10|11|12|13|14|15|
ports: in 0, out 0: | 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0|
r327i7n0 ~ # smpquery -D vlarb 0,1 1
# VLArbitration tables: DR path slid 65535; dlid 65535; 0,1 port 1 LowCap 8 HighCap 8
# Low priority VL Arbitration Table:
VL : |0x0 |0x1 |0x2 |0x3 |0x4 |0x5 |0x6 |0x7 |
WEIGHT: |0x1 |0x1 |0x1 |0x1 |0x1 |0x1 |0x1 |0x1 |
# High priority VL Arbitration Table:
VL : |0x0 |0x1 |0x2 |0x3 |0x4 |0x5 |0x6 |0x7 |
WEIGHT: |0x1 |0x1 |0x1 |0x1 |0x1 |0x1 |0x1 |0x1 |
r327i7n0 ~ # smpquery -D vlarb 0 1
# VLArbitration tables: DR path slid 65535; dlid 65535; 0 port 1 LowCap 8 HighCap 8
# Low priority VL Arbitration Table:
VL : |0x0 |0x1 |0x2 |0x3 |0x4 |0x5 |0x6 |0x7 |
WEIGHT: |0x20|0x20|0x20|0x20|0x20|0x20|0x20|0x20|
# High priority VL Arbitration Table:
VL : |0x0 |0x1 |0x2 |0x3 |0x4 |0x5 |0x6 |0x7 |
WEIGHT: |0x0 |0x0 |0x0 |0x0 |0x0 |0x0 |0x0 |0x0 |
on ib1, HCA port 2, Qos is enabled:
r327i7n0 ~ # smpquery -P2 -D sl2vl 0 2
# SL2VL table: DR path slid 65535; dlid 65535; 0
# SL: | 0| 1| 2| 3| 4| 5| 6| 7| 8| 9|10|11|12|13|14|15|
ports: in 0, out 0: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
r327i7n0 ~ # smpquery -P2 -D sl2vl 0,2 1
# SL2VL table: DR path slid 65535; dlid 65535; 0,2
# SL: | 0| 1| 2| 3| 4| 5| 6| 7| 8| 9|10|11|12|13|14|15|
ports: in 0, out 1: | 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0| 0|
ports: in 1, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 2, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 3, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 4, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 5, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 6, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 7, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 8, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 9, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 10, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 11, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 12, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 13, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 14, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 15, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 16, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 17, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 18, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 19, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 20, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 21, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 22, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 23, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 24, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 25, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 26, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 27, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 28, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 29, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 30, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 31, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 32, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 33, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 34, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 35, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
ports: in 36, out 1: | 0| 1| 2| 3| 4| 5| 6| 7| 3| 4| 5| 6| 7| 3| 4| 5|
r327i7n0 ~ # smpquery -P2 -D vlarb 0,2 1
# VLArbitration tables: DR path slid 65535; dlid 65535; 0,2 port 1 LowCap 8 HighCap 8
# Low priority VL Arbitration Table:
VL : |0x0 |0x1 |0x2 |0x3 |0x4 |0x5 |0x6 |0x7 |
WEIGHT: |0x0 |0x0 |0x0 |0x40|0x40|0x40|0x40|0x40|
# High priority VL Arbitration Table:
VL : |0x0 |0x1 |0x2 |0x0 |0x0 |0x0 |0x0 |0x0 |
WEIGHT: |0x80|0x40|0x40|0x0 |0x0 |0x0 |0x0 |0x0 |
r327i7n0 ~ # smpquery -P2 -D vlarb 0 2
# VLArbitration tables: DR path slid 65535; dlid 65535; 0 port 2 LowCap 8 HighCap 8
# Low priority VL Arbitration Table:
VL : |0x0 |0x1 |0x2 |0x3 |0x4 |0x5 |0x6 |0x7 |
WEIGHT: |0x0 |0x0 |0x0 |0x40|0x40|0x40|0x40|0x40|
# High priority VL Arbitration Table:
VL : |0x0 |0x1 |0x2 |0x0 |0x0 |0x0 |0x0 |0x0 |
WEIGHT: |0x80|0x40|0x40|0x0 |0x0 |0x0 |0x0 |0x0 |
>> Only in the case of FW bug?
>
> I don't think flow control is performed by FW.
>
>> Any tunable's that might impact this?
>
> No IBA standard ones AFAIK. Who's the HCA vendor ?
>
> -- Hal
>
>> bob
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-rdma" in
>> the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-rdma" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2012-05-18 14:35 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-05-18 6:05 watchdog timer Bob Ciotti
[not found] ` <4FB5E69A.7010602-NSQ8wuThN14@public.gmane.org>
2012-05-18 13:07 ` Hal Rosenstock
[not found] ` <4FB649A6.2060602-LDSdmyG8hGV8YrgS2mwiifqBs+8SCbDb@public.gmane.org>
2012-05-18 14:35 ` Bob Ciotti [this message]
[not found] ` <4FB65E30.4070805-NSQ8wuThN14@public.gmane.org>
2012-05-18 15:10 ` Ira Weiny
[not found] ` <20120518081029.01004d2c.weiny2-i2BcT+NCU+M@public.gmane.org>
2012-05-18 15:27 ` Hal Rosenstock
[not found] ` <4FB66A6C.1060703-LDSdmyG8hGV8YrgS2mwiifqBs+8SCbDb@public.gmane.org>
2012-05-21 17:08 ` Ira Weiny
[not found] ` <20120521100831.a434152f.weiny2-i2BcT+NCU+M@public.gmane.org>
2012-05-22 0:51 ` Bob Ciotti
[not found] ` <4FBAE311.3080909-NSQ8wuThN14@public.gmane.org>
2012-05-22 15:55 ` Ira Weiny
2012-05-18 19:10 ` Bob Ciotti
2012-05-18 15:17 ` Hal Rosenstock
[not found] ` <4FB66817.6050106-LDSdmyG8hGV8YrgS2mwiifqBs+8SCbDb@public.gmane.org>
2012-05-18 16:49 ` Bob Ciotti
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4FB65E30.4070805@nasa.gov \
--to=bob.ciotti-nsq8wuthn14@public.gmane.org \
--cc=hal-LDSdmyG8hGV8YrgS2mwiifqBs+8SCbDb@public.gmane.org \
--cc=linux-rdma-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.