From: Troy Kisky <troy.kisky@boundarydevices.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 9/9] mx6qsabrelite: Add splaschscreen support
Date: Sat, 02 Jun 2012 17:12:19 -0700 [thread overview]
Message-ID: <4FCAABE3.8050401@boundarydevices.com> (raw)
In-Reply-To: <CAOMZO5A00kB2wFZgbPLchDWghZW0uCFc+e3NOFw2u_abeRrhSg@mail.gmail.com>
On 6/2/2012 3:36 PM, Fabio Estevam wrote:
> Hi Dirk,
>
> On Sat, Jun 2, 2012 at 3:52 PM, Dirk Behme<dirk.behme@googlemail.com> wrote:
>
>> Maybe you could check [1]
>>
>> -#define CONFIG_SYS_I2C_SLAVE 0xfe
>> +#define CONFIG_SYS_I2C_SLAVE 0x1f
>>
>> then? I'm no I2C expert and I wasn't sure what to use for
>> CONFIG_SYS_I2C_SLAVE.
> Yes, 0x1f is the correct address for the Hannstar LVDS I2C slave address.
If 0x1f is the Hannstar LVDS address, then you definitely should NOT use
0x1f for the
CONFIG_SYS_I2C_SLAVE value.
CONFIG_SYS_I2C_SLAVE is meant to define which address the processor will respond to
in a multi-master bus environment. However, as mxc_i2c does not support slave mode
the entire discussion is moot.
Troy
next prev parent reply other threads:[~2012-06-03 0:12 UTC|newest]
Thread overview: 46+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-05-31 17:23 [U-Boot] [PATCH 1/9] mx6: Allow mx6 to access the IPUv3 registers Fabio Estevam
2012-05-31 17:23 ` [U-Boot] [PATCH 2/9] video: Rename CONFIG_VIDEO_MX5 Fabio Estevam
2012-06-22 11:36 ` Anatolij Gustschin
2012-05-31 17:23 ` [U-Boot] [PATCH 3/9] ipu_common: Only apply the erratum to MX51 Fabio Estevam
2012-06-22 11:36 ` Anatolij Gustschin
2012-05-31 17:23 ` [U-Boot] [PATCH 4/9] ipu_common: Let clk_ipu_enable/disable only run on MX51 and MX53 Fabio Estevam
2012-06-22 11:37 ` Anatolij Gustschin
2012-05-31 17:23 ` [U-Boot] [PATCH 5/9] ipu_common: Rename MXC_CCM_BASE Fabio Estevam
2012-06-22 11:37 ` Anatolij Gustschin
2012-05-31 17:24 ` [U-Boot] [PATCH 6/9] ipu_common: Do not hardcode the ipu_clk frequency Fabio Estevam
2012-06-22 11:38 ` Anatolij Gustschin
2012-05-31 17:24 ` [U-Boot] [PATCH 7/9] mxc_i2c: Allow MX6Q I2C3 to work Fabio Estevam
2012-05-31 22:24 ` Troy Kisky
2012-05-31 22:48 ` Fabio Estevam
2012-06-02 6:44 ` Dirk Behme
2012-05-31 17:24 ` [U-Boot] [PATCH 8/9] ipu_common: Add ldb_clk for use in parenting the pixel clock Fabio Estevam
2012-06-22 11:39 ` Anatolij Gustschin
2012-05-31 17:24 ` [U-Boot] [PATCH 9/9] mx6qsabrelite: Add splaschscreen support Fabio Estevam
2012-06-02 6:46 ` Dirk Behme
2012-06-02 18:22 ` Fabio Estevam
2012-06-02 18:52 ` Dirk Behme
2012-06-02 22:36 ` Fabio Estevam
2012-06-03 0:12 ` Troy Kisky [this message]
2012-06-03 7:29 ` Fabio Estevam
2012-07-31 9:07 ` Dirk Behme
2012-09-17 20:20 ` [U-Boot] [PATCH 0/2] i.MX6: mx6qsabrelite: Add splash screen support Eric Nelson
2012-09-17 20:20 ` [U-Boot] [PATCH 1/2] i.MX6: change register name for CCM_CHSCCDR to match ref. manual Eric Nelson
2012-09-17 20:20 ` [U-Boot] [PATCH 2/2] i.MX6: mx6qsabrelite: Add splash screen support Eric Nelson
2012-09-17 20:29 ` Fabio Estevam
2012-09-17 20:45 ` [U-Boot] [PATCH 0/2] " Anatolij Gustschin
2012-09-17 23:14 ` [U-Boot] [PATCH V2 " Eric Nelson
2012-09-17 23:14 ` [U-Boot] [PATCH V2 1/2] i.MX6: change register name for CCM_CHSCCDR to match ref. manual Eric Nelson
2012-09-17 23:14 ` [U-Boot] [PATCH V2 2/2] i.MX6: mx6qsabrelite: Add splash screen support Eric Nelson
2012-09-17 23:43 ` Fabio Estevam
2012-09-18 0:08 ` Eric Nelson
2012-09-18 0:43 ` Eric Nelson
2012-09-18 0:45 ` Fabio Estevam
2012-09-18 14:02 ` Eric Nelson
2012-09-18 14:42 ` Stefano Babic
2012-09-18 15:12 ` Eric Nelson
2012-09-18 7:47 ` Stefano Babic
2012-09-18 13:28 ` Eric Nelson
2012-09-18 13:50 ` Stefano Babic
2012-09-18 23:56 ` [U-Boot] Cleanup of CCGR registers (was [PATCH V2 2/2] i.MX6: mx6qsabrelite: Add splash screen support) Eric Nelson
2012-09-19 7:31 ` Stefano Babic
2012-06-22 11:35 ` [U-Boot] [PATCH 1/9] mx6: Allow mx6 to access the IPUv3 registers Anatolij Gustschin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4FCAABE3.8050401@boundarydevices.com \
--to=troy.kisky@boundarydevices.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.