All of lore.kernel.org
 help / color / mirror / Atom feed
From: Daniel Mack <zonque@gmail.com>
To: Joseph Salisbury <joseph.salisbury@canonical.com>
Cc: tiwai@suse.de, alsa-devel@alsa-project.org,
	Clemens Ladisch <clemens@ladisch.de>,
	philipp@dreimann.net
Subject: Re: [PATCH 1/2] ALSA: snd-usb: tighten EP_FLAG_RUNNING checks
Date: Thu, 12 Jul 2012 21:26:56 +0200	[thread overview]
Message-ID: <4FFF2500.6010703@gmail.com> (raw)
In-Reply-To: <4FFF232E.8020008@canonical.com>

On 12.07.2012 21:19, Joseph Salisbury wrote:
> On 07/12/2012 11:27 AM, Daniel Mack wrote:
>> On 12.07.2012 17:20, Clemens Ladisch wrote:
>>> Daniel Mack wrote:
>>>> On 12.07.2012 16:29, Clemens Ladisch wrote:
>>>>> Daniel Mack wrote:
>>>>>> In endpoint.c, bail out earlier in case the stream is stopped.
>>>>>> ...
>>>>>> @@ -350,7 +350,8 @@ static void snd_complete_urb(struct urb *urb)
>>>>>>  		     urb->status == -ENODEV ||		/* device removed */
>>>>>>  		     urb->status == -ECONNRESET ||	/* unlinked */
>>>>>>  		     urb->status == -ESHUTDOWN ||	/* device disabled */
>>>>>> -		     ep->chip->shutdown))		/* device disconnected */
>>>>>> +		     ep->chip->shutdown) ||		/* device disconnected */
>>>>>> +		     !test_bit(EP_FLAG_RUNNING, &ep->flags))
>>>>>>  		goto exit_clear;
>>>>>
>>>>> Is this really needed?
>>>>> The URBs will be unlinked at the same time.
>>>>
>>>> This just brings the code in sync with what we had before. If URBs are
>>>> just unlinked but not killed, they will return with data payload, and in
>>>> case of implicit feedback streams, the retire code could issue new
>>>> output packets.
>>>
>>> And is that bad?
>>>
>>> The EP_FLAG_RUNNING bit is cleared immediately before the URBs are
>>> unlinked, and some URB could have been completed regularly immediately
>>> before that.  So if there is any case where the additional test_bit()
>>> call prevents submitting a new playback packet, there is another similar
>>> case where you've just got such a playback packet anyway.
>>>
>>> In other words: if that test_bit() call were necessary to protect
>>> against something bad, it wouldn't be sufficient.
>>>
>>> The driver ensures that (implicit feedback) playback URBs are unlinked
>>> only after the corresponding capture URBs have been completely killed,
>>> doesn't it?
>>
>> You're right. Especially because sending out packets in implicit
>> feedback mode happens from queue_pending_output_urbs() which has an
>> extra chip.
>>
>> So we can drop the whole patch then. Thanks for the review!
>>
>>
>> Daniel
> 
> Hi Daniel,
> 
> I tested without your first patch.  I'm not sure why, but dropping the
> first patch(ALSA: snd-usb: tighten EP_FLAG_RUNNING checks) causes a long
> delay, about 30 seconds, during bootup of an ubuntu system.
> 
> During the delay, I am able to enter my password, but the system seems
> to be doing something in the background, slowing the login process.
> 
> I confirmed that adding the patch back causes the delay to go away.

That really sounds odd and totally unrelated. Is there any message in
dmesg that looks suspicious? Otherwise, I would ask you to test again.
Could be it was caused by something that runs on every n'th boot or so.


Daniel

      parent reply	other threads:[~2012-07-12 19:26 UTC|newest]

Thread overview: 10+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-07-12 13:19 [PATCH 1/2] ALSA: snd-usb: tighten EP_FLAG_RUNNING checks Daniel Mack
2012-07-12 13:19 ` [PATCH 2/2] ALSA: snd-usb: move calls to usb_set_interface Daniel Mack
2012-07-13  5:58   ` Takashi Iwai
2012-07-13  6:08     ` Daniel Mack
2012-07-13  7:33       ` Takashi Iwai
2012-07-12 14:29 ` [PATCH 1/2] ALSA: snd-usb: tighten EP_FLAG_RUNNING checks Clemens Ladisch
2012-07-12 14:58   ` Daniel Mack
2012-07-12 15:20     ` Clemens Ladisch
2012-07-12 15:27       ` Daniel Mack
     [not found]         ` <4FFF232E.8020008@canonical.com>
2012-07-12 19:26           ` Daniel Mack [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=4FFF2500.6010703@gmail.com \
    --to=zonque@gmail.com \
    --cc=alsa-devel@alsa-project.org \
    --cc=clemens@ladisch.de \
    --cc=joseph.salisbury@canonical.com \
    --cc=philipp@dreimann.net \
    --cc=tiwai@suse.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.