From: Prabhakar Lad <prabhakar.lad@ti.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v2 15/18] ARM: SPL: Convert davinci to CONFIG_SPL_FRAMEWORK
Date: Wed, 22 Aug 2012 15:43:42 +0530 [thread overview]
Message-ID: <5034B0D6.2050506@ti.com> (raw)
In-Reply-To: <CABkLObrz82GSpKO8yc7kUrTUNCwz0wPZ1nAeQytd876zWF_JFQ@mail.gmail.com>
Hi Tom,
On Wednesday 22 August 2012 03:34 PM, Christian Riesch wrote:
> Hi Tom,
>
> On Mon, Aug 20, 2012 at 6:45 PM, Tom Rini <trini@ti.com> wrote:
>> - Convert the non-relocation part of board_init_f to spl_board_init,
>> turn on CONFIG_SPL_BOARD_INIT in the configs.
>> - Remove duplicated code.
>> - Add spl_boot_device() that returns the statically chosen boot device.
>
> I tested the patchset on the LogicPD AM1808 experimenter's kit:
>
> make da850evm
> and flashing to SPI flash with
> mono sfh_OMAP-L138.exe -targetType AM1808 -p /dev/ttyUSB0 -flash_noubl
> u-boot.ais
>
I tried testing the same on omap-l138 (the entire patch set) for SPI
boot mode itsef, unfortunately the board doesn't even come up. Any Ideas ?
Thx,
--Prabhakar
> The board boots up fine, but after pressing the reset button or
> issuing the u-boot "reset" command, it is dead. Only power-cycling
> helps. Before enabling the SPL framework in this patch reset works
> fine. Any ideas?
>
> Regards, Christian
>
next prev parent reply other threads:[~2012-08-22 10:13 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-08-20 16:45 [U-Boot] [PATCH v2 0/18] ARM: SPL: Make more generic, merge DaVinci and OMAP Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 01/18] Makefile: Move SPL files to clobber, remove from clean Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 02/18] spl_mmc: Make FAT checks / calls guarded with CONFIG_SPL_FAT_SUPPORT Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 03/18] omap-common: SPL: Add CONFIG_SPL_DISPLAY_PRINT / spl_display_print() Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 04/18] omap-common: Fix typo in save_boot_params() in lowlevel_init.S Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 05/18] ARM: SPL: Rename omap_boot_device to spl_boot_device Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 06/18] ARM: SPL: Rename omap_boot_mode to spl_boot_mode() Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 07/18] ARM: SPL: Remove NAND_MODE_HW_ECC from spl_nand.c Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 08/18] ARM: SPL: Only call mem_malloc_init if configured Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 09/18] ARM: SPL: Add <asm/spl.h> and <asm/arch/spl.h> Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 10/18] ARM: SPL: Make spl_mmc.c more generic Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 11/18] ARM: SPL: Clean up spl.c / spl_nand.c slightly Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 12/18] ARM: SPL: Start hooking in the current SPI SPL support Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 13/18] ARM: SPL: Move gpmc_init() to spl_board_init() Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 14/18] SPL: Move the omap SPL framework to common/spl Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 15/18] ARM: SPL: Convert davinci to CONFIG_SPL_FRAMEWORK Tom Rini
2012-08-22 10:04 ` Christian Riesch
2012-08-22 10:13 ` Prabhakar Lad [this message]
2012-08-22 17:46 ` Tom Rini
2012-08-22 19:19 ` Tom Rini
2012-08-22 23:14 ` Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 16/18] da850_am18xxevm: Add README.da850_am18xxevm Tom Rini
2012-08-21 5:09 ` Prabhakar Lad
2012-08-21 15:34 ` Tom Rini
2012-08-22 4:46 ` Prabhakar Lad
2012-08-22 6:28 ` Tom Rini
2012-08-22 8:13 ` Christian Riesch
2012-08-22 9:07 ` Prabhakar Lad
2012-08-22 9:17 ` Christian Riesch
2012-08-22 10:05 ` Prabhakar Lad
2012-08-22 15:09 ` Christian Riesch
2012-08-23 4:51 ` Prabhakar Lad
2012-08-22 17:44 ` Tom Rini
2012-08-22 17:37 ` Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 17/18] SPL: Enhance drivers/mtd/nand/nand_spl_load.c Tom Rini
2012-08-24 21:09 ` Scott Wood
2012-08-24 21:10 ` Scott Wood
2012-08-24 21:17 ` Tom Rini
2012-08-24 21:20 ` Tom Rini
2012-08-24 21:30 ` Scott Wood
2012-08-24 22:56 ` Tom Rini
2012-08-20 16:45 ` [U-Boot] [PATCH v2 18/18] SPL: Enhance spi_spl_load to match the other load functions Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5034B0D6.2050506@ti.com \
--to=prabhakar.lad@ti.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.