* [Xenomai] Beagle-XM - ipipe-core-3.2.21
@ 2012-11-03 20:20 Robert Berger
2012-11-03 21:24 ` Gilles Chanteperdrix
2012-11-03 21:36 ` Gilles Chanteperdrix
0 siblings, 2 replies; 5+ messages in thread
From: Robert Berger @ 2012-11-03 20:20 UTC (permalink / raw)
To: xenomai
Hi,
I try to get Xenomai run on a Beagle-XM rev c.
That's what I use:
*) xenomai-head commit 9534fff1f0247c4c1a9bd104b0ef65df340ead4f
*) ipipe-core-3.2.21-arm-1.patch
*) ELDK 5.2.1 generic-armv7a
*) linux-stable 3.2.21
*) rootfs on 2nd partition of SD card (for now)
*) kernel loaded over tftp
That's what I observed so far:
1) default config
*) default kernel boots
*) ipipe patched kernel hangs:
Filename 'beagle-xm/uImage'.
Load address: 0x80200000
Loading: #################################################################
done
Bytes transferred = 3607600 (370c30 hex)
## Booting kernel from Legacy Image at 80200000 ...
Image Name: Linux-3.2.21-xenomai-student-dir
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3607536 Bytes = 3.4 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
--> hangs here <--
1) custom config (able to boot rootfs over nfs)
*) custom kernel boots with network support
*) ipipe patched kernel tells me this:
...
[ 0.342254] Division by zero in kernel.
[ 0.342315] [<c00134b8>] (unwind_backtrace+0x0/0xe0) from
[<c03837d4>] (Ldiv0+0x8/0x10)
[ 0.342376] [<c03837d4>] (Ldiv0+0x8/0x10) from [<c04df888>]
(rthal_arch_init+0x94/0xd8)
[ 0.342407] [<c04df888>] (rthal_arch_init+0x94/0xd8) from
[<c00c4564>] (rthal_init+0x7c/0x25c)
[ 0.342437] [<c00c4564>] (rthal_init+0x7c/0x25c) from [<c084f58c>]
(__xeno_sys_init+0x20/0x30c)
[ 0.342468] [<c084f58c>] (__xeno_sys_init+0x20/0x30c) from
[<c000883c>] (do_one_initcall+0x90/0x160)
[ 0.342498] [<c000883c>] (do_one_initcall+0x90/0x160) from
[<c08388a0>] (kernel_init+0xd8/0x180)
[ 0.342529] [<c08388a0>] (kernel_init+0xd8/0x180) from [<c000dfec>]
(kernel_thread_exit+0x0/0x8)
[ 0.342559] Division by zero in kernel.
[ 0.342590] [<c00134b8>] (unwind_backtrace+0x0/0xe0) from
[<c03837d4>] (Ldiv0+0x8/0x10)
[ 0.342620] [<c03837d4>] (Ldiv0+0x8/0x10) from [<c03837a4>]
(__aeabi_uidivmod+0x8/0x18)
[ 0.342620] [<c03837a4>] (__aeabi_uidivmod+0x8/0x18) from
[<c04df898>] (rthal_arch_init+0xa4/0xd8)
[ 0.342651] [<c04df898>] (rthal_arch_init+0xa4/0xd8) from
[<c00c4564>] (rthal_init+0x7c/0x25c)
[ 0.342681] [<c00c4564>] (rthal_init+0x7c/0x25c) from [<c084f58c>]
(__xeno_sys_init+0x20/0x30c)
[ 0.342712] [<c084f58c>] (__xeno_sys_init+0x20/0x30c) from
[<c000883c>] (do_one_initcall+0x90/0x160)
[ 0.342742] [<c000883c>] (do_one_initcall+0x90/0x160) from
[<c08388a0>] (kernel_init+0xd8/0x180)
[ 0.342773] [<c08388a0>] (kernel_init+0xd8/0x180) from [<c000dfec>]
(kernel_thread_exit+0x0/0x8)
[ 0.342895] Division by zero in kernel.
[ 0.342926] [<c00134b8>] (unwind_backtrace+0x0/0xe0) from
[<c0382d2c>] (Ldiv0_64+0x8/0x18)
[ 0.342956] [<c0382d2c>] (Ldiv0_64+0x8/0x18) from [<c04df8a4>]
(rthal_arch_init+0xb0/0xd8)
[ 0.342987] [<c04df8a4>] (rthal_arch_init+0xb0/0xd8) from
[<c00c4564>] (rthal_init+0x7c/0x25c)
[ 0.343017] [<c00c4564>] (rthal_init+0x7c/0x25c) from [<c084f58c>]
(__xeno_sys_init+0x20/0x30c)
[ 0.343048] [<c084f58c>] (__xeno_sys_init+0x20/0x30c) from
[<c000883c>] (do_one_initcall+0x90/0x160)
[ 0.343078] [<c000883c>] (do_one_initcall+0x90/0x160) from
[<c08388a0>] (kernel_init+0xd8/0x180)
[ 0.343109] [<c08388a0>] (kernel_init+0xd8/0x180) from [<c000dfec>]
(kernel_thread_exit+0x0/0x8)
[ 0.343261] Division by zero in kernel.
[ 0.343292] [<c00134b8>] (unwind_backtrace+0x0/0xe0) from
[<c0382d2c>] (Ldiv0_64+0x8/0x18)
[ 0.343322] [<c0382d2c>] (Ldiv0_64+0x8/0x18) from [<c04df8b0>]
(rthal_arch_init+0xbc/0xd8)
[ 0.343353] [<c04df8b0>] (rthal_arch_init+0xbc/0xd8) from
[<c00c4564>] (rthal_init+0x7c/0x25c)
[ 0.343383] [<c00c4564>] (rthal_init+0x7c/0x25c) from [<c084f58c>]
(__xeno_sys_init+0x20/0x30c)
[ 0.343414] [<c084f58c>] (__xeno_sys_init+0x20/0x30c) from
[<c000883c>] (do_one_initcall+0x90/0x160)
[ 0.343444] [<c000883c>] (do_one_initcall+0x90/0x160) from
[<c08388a0>] (kernel_init+0xd8/0x180)
[ 0.343475] [<c08388a0>] (kernel_init+0xd8/0x180) from [<c000dfec>]
(kernel_thread_exit+0x0/0x8)
[ 0.343475] Xenomai: system init failed, code -9.
[ 0.343505] Xenomai: native skin init failed, code -9.
[ 0.343505] Xenomai: starting POSIX services.
[ 0.343536] Xenomai: POSIX skin init failed, code -9.
[ 0.343536] Xenomai: RTDM skin init failed, code -9.
...
[ 5.234558] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 5.241973] Waiting 2sec before mounting root device...
^[^[^[^[[B^[[B^[[B^[[A[ 464.874786] smsc95xx 1-2.1:1.0: eth0: register
'smsc95xx' at usb-ehci-omap.0-2.1, smsc95xx USB 2.0 Ethernet,
62:9d:d5:c4:cf:f8
[ 464.887939] VFS: Cannot open root device "mmcblk0p2" or
unknown-block(0,0)
[ 464.895233] Please append a correct "root=" boot option; here are the
available partitions:
[ 464.904113] Kernel panic - not syncing: VFS: Unable to mount root fs
on unknown-block(0,0)
[ 464.912811] [<c00134b8>] (unwind_backtrace+0x0/0xe0) from
[<c05e5bec>] (panic+0x50/0x188)
[ 464.921447] [<c05e5bec>] (panic+0x50/0x188) from [<c0838ca0>]
(mount_block_root+0x1d0/0x214)
[ 464.930328] [<c0838ca0>] (mount_block_root+0x1d0/0x214) from
[<c0838eb0>] (mount_root+0xe4/0x100)
[ 464.939636] [<c0838eb0>] (mount_root+0xe4/0x100) from [<c0839028>]
(prepare_namespace+0x15c/0x1bc)
[ 464.949188] [<c0839028>] (prepare_namespace+0x15c/0x1bc) from
[<c0838910>] (kernel_init+0x148/0x180)
[ 464.958831] [<c0838910>] (kernel_init+0x148/0x180) from [<c000dfec>]
(kernel_thread_exit+0x0/0x8)
more detailed info about Linux booting is here: http://pastebin.com/54bBuXQi
Do you have anything to suggest?
Regards,
Robert
...Distributed computing means that you cannot get your work done when
some computer you never heard of crashes" -- L.Lamport
My public pgp key is available,at:
http://pgp.mit.edu:11371/pks/lookup?op=get&search=0x90320BF1
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [Xenomai] Beagle-XM - ipipe-core-3.2.21
2012-11-03 20:20 [Xenomai] Beagle-XM - ipipe-core-3.2.21 Robert Berger
@ 2012-11-03 21:24 ` Gilles Chanteperdrix
2012-11-03 21:49 ` Robert Berger
2012-11-03 21:36 ` Gilles Chanteperdrix
1 sibling, 1 reply; 5+ messages in thread
From: Gilles Chanteperdrix @ 2012-11-03 21:24 UTC (permalink / raw)
To: Robert Berger; +Cc: xenomai
On 11/03/2012 09:20 PM, Robert Berger wrote:
> Hi,
>
> I try to get Xenomai run on a Beagle-XM rev c.
>
> That's what I use:
>
> *) xenomai-head commit 9534fff1f0247c4c1a9bd104b0ef65df340ead4f
> *) ipipe-core-3.2.21-arm-1.patch
> *) ELDK 5.2.1 generic-armv7a
> *) linux-stable 3.2.21
> *) rootfs on 2nd partition of SD card (for now)
> *) kernel loaded over tftp
What version of the Linux kernel? Is it a vanilla 3.2.21?
>
> That's what I observed so far:
>
> 1) default config
> *) default kernel boots
> *) ipipe patched kernel hangs:
>
> Filename 'beagle-xm/uImage'.
> Load address: 0x80200000
> Loading: #################################################################
> done
> Bytes transferred = 3607600 (370c30 hex)
> ## Booting kernel from Legacy Image at 80200000 ...
> Image Name: Linux-3.2.21-xenomai-student-dir
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 3607536 Bytes = 3.4 MiB
> Load Address: 80008000
> Entry Point: 80008000
> Verifying Checksum ... OK
> Loading Kernel Image ... OK
> OK
>
> Starting kernel ...
>
> Uncompressing Linux... done, booting the kernel.
>
> --> hangs here <--
As repeated many times on this list and probably on the linux-arm-kernel
mailing list too, in that case, use earlyprintk.
>
> 1) custom config (able to boot rootfs over nfs)
> *) custom kernel boots with network support
> *) ipipe patched kernel tells me this:
>
> ...
> [ 0.342254] Division by zero in kernel.
> [ 0.342315] [<c00134b8>] (unwind_backtrace+0x0/0xe0) from
> [<c03837d4>] (Ldiv0+0x8/0x10)
> [ 0.342376] [<c03837d4>] (Ldiv0+0x8/0x10) from [<c04df888>]
> (rthal_arch_init+0x94/0xd8)
> [ 0.342407] [<c04df888>] (rthal_arch_init+0x94/0xd8) from
> [<c00c4564>] (rthal_init+0x7c/0x25c)
> [ 0.342437] [<c00c4564>] (rthal_init+0x7c/0x25c) from [<c084f58c>]
> (__xeno_sys_init+0x20/0x30c)
> [ 0.342468] [<c084f58c>] (__xeno_sys_init+0x20/0x30c) from
> [<c000883c>] (do_one_initcall+0x90/0x160)
> [ 0.342498] [<c000883c>] (do_one_initcall+0x90/0x160) from
> [<c08388a0>] (kernel_init+0xd8/0x180)
> [ 0.342529] [<c08388a0>] (kernel_init+0xd8/0x180) from [<c000dfec>]
> (kernel_thread_exit+0x0/0x8)
> [ 0.342559] Division by zero in kernel.
> [ 0.342590] [<c00134b8>] (unwind_backtrace+0x0/0xe0) from
> [<c03837d4>] (Ldiv0+0x8/0x10)
> [ 0.342620] [<c03837d4>] (Ldiv0+0x8/0x10) from [<c03837a4>]
> (__aeabi_uidivmod+0x8/0x18)
> [ 0.342620] [<c03837a4>] (__aeabi_uidivmod+0x8/0x18) from
> [<c04df898>] (rthal_arch_init+0xa4/0xd8)
> [ 0.342651] [<c04df898>] (rthal_arch_init+0xa4/0xd8) from
> [<c00c4564>] (rthal_init+0x7c/0x25c)
> [ 0.342681] [<c00c4564>] (rthal_init+0x7c/0x25c) from [<c084f58c>]
> (__xeno_sys_init+0x20/0x30c)
> [ 0.342712] [<c084f58c>] (__xeno_sys_init+0x20/0x30c) from
> [<c000883c>] (do_one_initcall+0x90/0x160)
> [ 0.342742] [<c000883c>] (do_one_initcall+0x90/0x160) from
> [<c08388a0>] (kernel_init+0xd8/0x180)
> [ 0.342773] [<c08388a0>] (kernel_init+0xd8/0x180) from [<c000dfec>]
> (kernel_thread_exit+0x0/0x8)
> [ 0.342895] Division by zero in kernel.
> [ 0.342926] [<c00134b8>] (unwind_backtrace+0x0/0xe0) from
> [<c0382d2c>] (Ldiv0_64+0x8/0x18)
> [ 0.342956] [<c0382d2c>] (Ldiv0_64+0x8/0x18) from [<c04df8a4>]
> (rthal_arch_init+0xb0/0xd8)
> [ 0.342987] [<c04df8a4>] (rthal_arch_init+0xb0/0xd8) from
> [<c00c4564>] (rthal_init+0x7c/0x25c)
> [ 0.343017] [<c00c4564>] (rthal_init+0x7c/0x25c) from [<c084f58c>]
> (__xeno_sys_init+0x20/0x30c)
> [ 0.343048] [<c084f58c>] (__xeno_sys_init+0x20/0x30c) from
> [<c000883c>] (do_one_initcall+0x90/0x160)
> [ 0.343078] [<c000883c>] (do_one_initcall+0x90/0x160) from
> [<c08388a0>] (kernel_init+0xd8/0x180)
> [ 0.343109] [<c08388a0>] (kernel_init+0xd8/0x180) from [<c000dfec>]
> (kernel_thread_exit+0x0/0x8)
> [ 0.343261] Division by zero in kernel.
> [ 0.343292] [<c00134b8>] (unwind_backtrace+0x0/0xe0) from
> [<c0382d2c>] (Ldiv0_64+0x8/0x18)
> [ 0.343322] [<c0382d2c>] (Ldiv0_64+0x8/0x18) from [<c04df8b0>]
> (rthal_arch_init+0xbc/0xd8)
> [ 0.343353] [<c04df8b0>] (rthal_arch_init+0xbc/0xd8) from
> [<c00c4564>] (rthal_init+0x7c/0x25c)
> [ 0.343383] [<c00c4564>] (rthal_init+0x7c/0x25c) from [<c084f58c>]
> (__xeno_sys_init+0x20/0x30c)
> [ 0.343414] [<c084f58c>] (__xeno_sys_init+0x20/0x30c) from
> [<c000883c>] (do_one_initcall+0x90/0x160)
> [ 0.343444] [<c000883c>] (do_one_initcall+0x90/0x160) from
> [<c08388a0>] (kernel_init+0xd8/0x180)
> [ 0.343475] [<c08388a0>] (kernel_init+0xd8/0x180) from [<c000dfec>]
> (kernel_thread_exit+0x0/0x8)
> [ 0.343475] Xenomai: system init failed, code -9.
> [ 0.343505] Xenomai: native skin init failed, code -9.
> [ 0.343505] Xenomai: starting POSIX services.
> [ 0.343536] Xenomai: POSIX skin init failed, code -9.
> [ 0.343536] Xenomai: RTDM skin init failed, code -9.
> ...
> [ 5.234558] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
> [ 5.241973] Waiting 2sec before mounting root device...
> ^[^[^[^[[B^[[B^[[B^[[A[ 464.874786] smsc95xx 1-2.1:1.0: eth0: register
> 'smsc95xx' at usb-ehci-omap.0-2.1, smsc95xx USB 2.0 Ethernet,
> 62:9d:d5:c4:cf:f8
> [ 464.887939] VFS: Cannot open root device "mmcblk0p2" or
> unknown-block(0,0)
> [ 464.895233] Please append a correct "root=" boot option; here are the
> available partitions:
> [ 464.904113] Kernel panic - not syncing: VFS: Unable to mount root fs
> on unknown-block(0,0)
> [ 464.912811] [<c00134b8>] (unwind_backtrace+0x0/0xe0) from
> [<c05e5bec>] (panic+0x50/0x188)
> [ 464.921447] [<c05e5bec>] (panic+0x50/0x188) from [<c0838ca0>]
> (mount_block_root+0x1d0/0x214)
> [ 464.930328] [<c0838ca0>] (mount_block_root+0x1d0/0x214) from
> [<c0838eb0>] (mount_root+0xe4/0x100)
> [ 464.939636] [<c0838eb0>] (mount_root+0xe4/0x100) from [<c0839028>]
> (prepare_namespace+0x15c/0x1bc)
> [ 464.949188] [<c0839028>] (prepare_namespace+0x15c/0x1bc) from
> [<c0838910>] (kernel_init+0x148/0x180)
> [ 464.958831] [<c0838910>] (kernel_init+0x148/0x180) from [<c000dfec>]
> (kernel_thread_exit+0x0/0x8)
>
> more detailed info about Linux booting is here: http://pastebin.com/54bBuXQi
>
> Do you have anything to suggest?
As repeated many times on this list, a stack trace is meaningless if you
do not provide us with the disassembly of the function which fails. In
that case that would be rthal_arch_init. Anyway, something is probably
wrong with the registration of the tsc emulation, or with the ipipe_timer.
--
Gilles.
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: [Xenomai] Beagle-XM - ipipe-core-3.2.21
2012-11-03 20:20 [Xenomai] Beagle-XM - ipipe-core-3.2.21 Robert Berger
2012-11-03 21:24 ` Gilles Chanteperdrix
@ 2012-11-03 21:36 ` Gilles Chanteperdrix
2012-11-03 22:13 ` Robert Berger
1 sibling, 1 reply; 5+ messages in thread
From: Gilles Chanteperdrix @ 2012-11-03 21:36 UTC (permalink / raw)
To: Robert Berger; +Cc: xenomai
On 11/03/2012 09:20 PM, Robert Berger wrote:
> more detailed info about Linux booting is here: http://pastebin.com/54bBuXQi
Please disable CONFIG_SMP. The I-pipe for 3.2.21 does not support
SMP_ON_UP yet, it has only be added to 3.4.
--
Gilles.
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2012-11-03 22:13 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-11-03 20:20 [Xenomai] Beagle-XM - ipipe-core-3.2.21 Robert Berger
2012-11-03 21:24 ` Gilles Chanteperdrix
2012-11-03 21:49 ` Robert Berger
2012-11-03 21:36 ` Gilles Chanteperdrix
2012-11-03 22:13 ` Robert Berger
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.