From: Udo van den Heuvel <udovdh@xs4all.nl>
To: linux-usb@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>,
Jan Ceuleers <jan.ceuleers@computer.org>,
Clemens Ladisch <clemens@ladisch.de>,
Simon Jones <sijones2010@gmail.com>,
linux-kernel@vger.kernel.org
Subject: Re: 3.4.4: disabling irq
Date: Sat, 01 Dec 2012 09:52:21 +0100 [thread overview]
Message-ID: <50B9C545.4060808@xs4all.nl> (raw)
In-Reply-To: <Pine.LNX.4.44L0.1211191139140.1598-100000@iolanthe.rowland.org>
On 2012-11-19 17:41, Alan Stern wrote:
> On Sat, 17 Nov 2012, Udo van den Heuvel wrote:
>> How to proceed next?
>
> Firstly, what does /proc/interrupts say?
>
> Secondly, try building a kernel with the patch below and
> CONFIG_USB_DEBUG enabled. Let's see what the dmesg log says when the
> problem occurs.
Message from syslogd@a at Dec 1 09:46:01 ...
kernel:Disabling IRQ #18
^C
[root@a mesa]# cat /sys/kernel/debug/usb/ohci/*/registers
bus pci, device 0000:00:12.0
OHCI Host Controller
ohci_hcd
OHCI 1.0, NO legacy support registers, rh state running
control 0x08f HCFS=operational IE PLE CBSR=3
cmdstatus 0x00000 SOC=0
intrstatus 0x00000024 FNO SF
intrenable 0x8000005a MIE RHSC UE RD WDH
ed_controlhead 00004000
hcca frame 0xa078
fmintvl 0xa7782edf FIT FSMPS=0xa778 FI=0x2edf
fmremaining 0x80001c56 FRT FR=0x1c56
periodicstart 0x2a2f
lsthresh 0x0628
hub poll timer off
roothub.a 02001205 POTPGT=2 NOCP NPS NDP=5(5)
roothub.b 00000000 PPCM=0000 DR=0000
roothub.status 00008000 DRWE
roothub.portstatus [0] 0x00000100 PPS
roothub.portstatus [1] 0x00000303 LSDA PPS PES CCS
roothub.portstatus [2] 0x00000100 PPS
roothub.portstatus [3] 0x00000100 PPS
roothub.portstatus [4] 0x00000100 PPS
bus pci, device 0000:00:13.0
OHCI Host Controller
ohci_hcd
OHCI 1.0, NO legacy support registers, rh state running
control 0x08f HCFS=operational IE PLE CBSR=3
cmdstatus 0x00000 SOC=0
intrstatus 0x00000026 FNO SF WDH
intrenable 0x8000005a MIE RHSC UE RD WDH
ed_controlhead 00092000
hcca frame 0xa2ab
fmintvl 0xa7782edf FIT FSMPS=0xa778 FI=0x2edf
fmremaining 0x8000184a FRT FR=0x184a
periodicstart 0x2a2f
lsthresh 0x0628
hub poll timer off
roothub.a 02001205 POTPGT=2 NOCP NPS NDP=5(5)
roothub.b 00000000 PPCM=0000 DR=0000
roothub.status 00008000 DRWE
roothub.portstatus [0] 0x00000100 PPS
roothub.portstatus [1] 0x00000100 PPS
roothub.portstatus [2] 0x00000100 PPS
roothub.portstatus [3] 0x00000103 PPS PES CCS
roothub.portstatus [4] 0x00000100 PPS
bus pci, device 0000:00:14.5
OHCI Host Controller
ohci_hcd
OHCI 1.0, NO legacy support registers, rh state running
control 0x083 HCFS=operational CBSR=3
cmdstatus 0x00000 SOC=0
intrstatus 0x00000024 FNO SF
intrenable 0x8000005a MIE RHSC UE RD WDH
hcca frame 0xa000
fmintvl 0xa7782edf FIT FSMPS=0xa778 FI=0x2edf
fmremaining 0x800014da FRT FR=0x14da
periodicstart 0x2a2f
lsthresh 0x0628
hub poll timer off
roothub.a 02001202 POTPGT=2 NOCP NPS NDP=2(2)
roothub.b 00000000 PPCM=0000 DR=0000
roothub.status 00008000 DRWE
roothub.portstatus [0] 0x00000100 PPS
roothub.portstatus [1] 0x00000100 PPS
[root@a mesa]# cat /sys/kernel/debug/usb/devices
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 5
B: Alloc=757/900 us (84%), #Int= 0, #Iso= 3
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 3.06
S: Manufacturer=Linux 3.6.7 ohci_hcd
S: Product=OHCI Host Controller
S: SerialNumber=0000:00:13.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0471 ProdID=0311 Rev= 0.03
S: SerialNumber=01690000A5000000
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=Philips webcam
E: Ad=82(I) Atr=03(Int.) MxPS= 1 Ivl=32ms
E: Ad=85(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 0 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=Philips webcam
E: Ad=82(I) Atr=03(Int.) MxPS= 1 Ivl=32ms
E: Ad=85(I) Atr=01(Isoc) MxPS= 196 Ivl=1ms
I: If#= 0 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=Philips webcam
E: Ad=82(I) Atr=03(Int.) MxPS= 1 Ivl=32ms
E: Ad=85(I) Atr=01(Isoc) MxPS= 292 Ivl=1ms
I: If#= 0 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=Philips webcam
E: Ad=82(I) Atr=03(Int.) MxPS= 1 Ivl=32ms
E: Ad=85(I) Atr=01(Isoc) MxPS= 448 Ivl=1ms
I: If#= 0 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=Philips webcam
E: Ad=82(I) Atr=03(Int.) MxPS= 1 Ivl=32ms
E: Ad=85(I) Atr=01(Isoc) MxPS= 592 Ivl=1ms
I: If#= 0 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=Philips webcam
E: Ad=82(I) Atr=03(Int.) MxPS= 1 Ivl=32ms
E: Ad=85(I) Atr=01(Isoc) MxPS= 704 Ivl=1ms
I: If#= 0 Alt= 6 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=Philips webcam
E: Ad=82(I) Atr=03(Int.) MxPS= 1 Ivl=32ms
E: Ad=85(I) Atr=01(Isoc) MxPS= 776 Ivl=1ms
I: If#= 0 Alt= 7 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=Philips webcam
E: Ad=82(I) Atr=03(Int.) MxPS= 1 Ivl=32ms
E: Ad=85(I) Atr=01(Isoc) MxPS= 840 Ivl=1ms
I: If#= 0 Alt= 8 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=Philips webcam
E: Ad=82(I) Atr=03(Int.) MxPS= 1 Ivl=32ms
E: Ad=85(I) Atr=01(Isoc) MxPS= 896 Ivl=1ms
I:* If#= 0 Alt= 9 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=Philips webcam
E: Ad=82(I) Atr=03(Int.) MxPS= 1 Ivl=32ms
E: Ad=85(I) Atr=01(Isoc) MxPS= 960 Ivl=1ms
I: If#= 0 Alt=10 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=Philips webcam
E: Ad=82(I) Atr=03(Int.) MxPS= 1 Ivl=32ms
E: Ad=85(I) Atr=01(Isoc) MxPS= 960 Ivl=1ms
I:* If#= 1 Alt= 0 #EPs= 0 Cls=01(audio) Sub=01 Prot=00 Driver=snd-usb-audio
I:* If#= 2 Alt= 0 #EPs= 0 Cls=01(audio) Sub=02 Prot=00 Driver=snd-usb-audio
I: If#= 2 Alt= 1 #EPs= 1 Cls=01(audio) Sub=02 Prot=00 Driver=snd-usb-audio
E: Ad=84(I) Atr=01(Isoc) MxPS= 90 Ivl=1ms
I: If#= 2 Alt= 2 #EPs= 1 Cls=01(audio) Sub=02 Prot=00 Driver=snd-usb-audio
E: Ad=84(I) Atr=01(Isoc) MxPS= 46 Ivl=1ms
I: If#= 2 Alt= 3 #EPs= 1 Cls=01(audio) Sub=02 Prot=00 Driver=snd-usb-audio
E: Ad=84(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 2 Alt= 4 #EPs= 1 Cls=01(audio) Sub=02 Prot=00 Driver=snd-usb-audio
E: Ad=84(I) Atr=01(Isoc) MxPS= 16 Ivl=1ms
T: Bus=11 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=5000 MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 3.00 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
P: Vendor=1d6b ProdID=0003 Rev= 3.06
S: Manufacturer=Linux 3.6.7 xhci_hcd
S: Product=xHCI Host Controller
S: SerialNumber=0000:02:00.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=10 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.06
S: Manufacturer=Linux 3.6.7 xhci_hcd
S: Product=xHCI Host Controller
S: SerialNumber=0000:02:00.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=09 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=5000 MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 3.00 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
P: Vendor=1d6b ProdID=0003 Rev= 3.06
S: Manufacturer=Linux 3.6.7 xhci_hcd
S: Product=xHCI Host Controller
S: SerialNumber=0000:00:10.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=08 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.06
S: Manufacturer=Linux 3.6.7 xhci_hcd
S: Product=xHCI Host Controller
S: SerialNumber=0000:00:10.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=07 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=5000 MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 3.00 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
P: Vendor=1d6b ProdID=0003 Rev= 3.06
S: Manufacturer=Linux 3.6.7 xhci_hcd
S: Product=xHCI Host Controller
S: SerialNumber=0000:00:10.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=06 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.06
S: Manufacturer=Linux 3.6.7 xhci_hcd
S: Product=xHCI Host Controller
S: SerialNumber=0000:00:10.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=02(comm.) Sub=00 Prot=00 MxPS=64 #Cfgs= 2
P: Vendor=0525 ProdID=a4a2 Rev= 2.16
S: Manufacturer=Linux 2.6.21-omap1/musb_hdrc
S: Product=RNDIS/Ethernet Gadget
C: #Ifs= 2 Cfg#= 2 Atr=e0 MxPwr= 8mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=ff Driver=
E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr= 8mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=(none)
E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_subset
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_subset
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=05 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 5
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.06
S: Manufacturer=Linux 3.6.7 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:13.2
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 5
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.06
S: Manufacturer=Linux 3.6.7 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:12.2
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 3.06
S: Manufacturer=Linux 3.6.7 ohci_hcd
S: Product=OHCI Host Controller
S: SerialNumber=0000:00:14.5
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 5
B: Alloc= 11/900 us ( 1%), #Int= 1, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 3.06
S: Manufacturer=Linux 3.6.7 ohci_hcd
S: Product=OHCI Host Controller
S: SerialNumber=0000:00:12.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=046d ProdID=c00c Rev= 6.20
S: Manufacturer=Logitech
S: Product=USB Mouse
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=usbhid
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=10ms
[root@a mesa]# service motion stop
Stopping motion (via systemctl): [ OK ]
[root@a mesa]# rmmod pwc
[root@a mesa]# echo 0000:00:13.0 >/sys/bus/pci/drivers/ohci_hcd/unbind
[root@a mesa]# echo 0000:00:13.0 >/sys/bus/pci/drivers/ohci_hcd/bind
[root@a mesa]# modprobe pwc
[root@a mesa]# service motion start
Starting motion (via systemctl): [ OK ]
[root@a mesa]# dmesg|sort|uniq
ehci_hcd 0000:00:13.2: GetStatus port:4 status 001803 0 ACK POWER sig=j
CSC CONNECT
ehci_hcd 0000:00:13.2: GetStatus port:4 status 003002 0 ACK POWER OWNER
sig=se0 CSC
ehci_hcd 0000:00:13.2: GetStatus port:4 status 003801 0 ACK POWER OWNER
sig=j CONNECT
ehci_hcd 0000:00:13.2: port 4 full speed --> companion
hub 2-0:1.0: 5 ports detected
hub 2-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x101
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current protection
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: port 4, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: power on to power good time: 4ms
hub 2-0:1.0: standalone hub
hub 2-0:1.0: state 7 ports 5 chg 0000 evt 0010
hub 2-0:1.0: trying to enable port power on non-switchable hub
hub 2-0:1.0: USB hub found
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100
hub 5-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501
hub 5-0:1.0: port 4 not reset yet, waiting 50ms
hub 5-0:1.0: port 4, status 0100, change 0001, 12 Mb/s
hub 5-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 5-0:1.0: state 7 ports 5 chg 0000 evt 0010
input: PWC snapshot button as
/devices/pci0000:00/0000:00:13.0/usb2/2-4/input/input8
ohci_hcd 0000:00:12.0: IRQ: 24 8000005a
ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:13.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:13.0: created debug files
ohci_hcd 0000:00:13.0: ed_controlhead 00092000
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [3] = 0x00010100 CSC PPS
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [3] = 0x00010101 CSC
PPS CCS
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [3] = 0x00100103
PRSC PPS PES CCS
ohci_hcd 0000:00:13.0: hcca frame #0004
ohci_hcd 0000:00:13.0: hcca frame #b161
ohci_hcd 0000:00:13.0: intrenable 0x8000005a MIE RHSC UE RD WDH
ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:13.0: intrstatus 0x00000024 FNO SF
ohci_hcd 0000:00:13.0: irq 18, io mem 0xfeb4e000
ohci_hcd 0000:00:13.0: IRQ: 44 8000001a
ohci_hcd 0000:00:13.0: IRQ: 4 8000001a
ohci_hcd 0000:00:13.0: IRQ: 4 8000005a
ohci_hcd 0000:00:13.0: IRQ: 64 5a
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers, rh state
running
ohci_hcd 0000:00:13.0: OHCI controller state
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: remove, state 1
ohci_hcd 0000:00:13.0: roothub.a 02001205 POTPGT=2 NOCP NPS NDP=5(5)
ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:13.0: roothub graceful disconnect
ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [3] 0x00000103 PPS PES CCS
ohci_hcd 0000:00:13.0: roothub.portstatus [3] 0x00010100 CSC PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [4] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:13.0: shutdown urb ffff8801d86233c0 ep1in-intr
ohci_hcd 0000:00:13.0: supports USB remote wakeup
ohci_hcd 0000:00:13.0: USB bus 2 deregistered
ohci_hcd 0000:00:14.5: IRQ: 24 8000005a
Philips webcam 2-4:1.0: usb_probe_interface
Philips webcam 2-4:1.0: usb_probe_interface - got id
pwc: Error (-1) re-submitting urb in pwc_isoc_handler.
pwc: Iso frame 0 has error -18
pwc: Iso frame 1 has error -114
pwc: Iso frame 1 has error -18
pwc: Iso frame 2 has error -18
pwc: Iso frame 3 has error -114
pwc: Iso frame 3 has error -18
pwc: Iso frame 4 has error -18
pwc: Iso frame 5 has error -114
pwc: Iso frame 5 has error -18
pwc: Iso frame 6 has error -18
pwc: Iso frame 7 has error -114
pwc: Iso frame 7 has error -18
pwc: Iso frame 8 has error -18
pwc: Iso frame 9 has error -114
pwc: Iso frame 9 has error -18
pwc: Philips PCVC740K (ToUCam Pro)/PCVC840 (ToUCam II) USB webcam detected.
pwc: Registered as video0.
snd-usb-audio 2-4:1.1: usb_probe_interface
snd-usb-audio 2-4:1.1: usb_probe_interface - got id
usb 2-4: adding 2-4:1.0 (config #1, interface 0)
usb 2-4: adding 2-4:1.1 (config #1, interface 1)
usb 2-4: adding 2-4:1.2 (config #1, interface 2)
usb 2-4: configuration #1 chosen from 1 choice
usb 2-4: default language 0x0409
usb 2-4: ep0 maxpacket = 8
usb 2-4: new full-speed USB device number 2 using ohci_hcd
usb 2-4: New USB device found, idVendor=0471, idProduct=0311
usb 2-4: New USB device strings: Mfr=0, Product=0, SerialNumber=1
usb 2-4: SerialNumber: 01690000A1000010
usb 2-4: skipped 1 descriptor after endpoint
usb 2-4: skipped 2 descriptors after interface
usb 2-4: skipped 4 descriptors after interface
usb 2-4: udev 2, busnum 2, minor = 129
usb 2-4: unregistering device
usb 2-4: unregistering interface 2-4:1.0
usb 2-4: unregistering interface 2-4:1.1
usb 2-4: unregistering interface 2-4:1.2
usb 2-4: usb_disable_device nuking all URBs
usb 2-4: USB disconnect, device number 2
usb 2-4: usb_probe_device
usbcore: deregistering interface driver Philips webcam
usbcore: registered new interface driver Philips webcam
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb usb2: configuration #1 chosen from 1 choice
usb usb2: default language 0x0409
usb usb2: Manufacturer: Linux 3.6.7 ohci_hcd
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: SerialNumber: 0000:00:13.0
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: unregistering device
usb usb2: unregistering interface 2-0:1.0
usb usb2: usb_disable_device nuking all URBs
usb usb2: USB disconnect, device number 1
usb usb2: usb_probe_device
[root@a mesa]# ^C
I had to hurry as the debug patch overflows dmesg very quickly.
That is the reason why the dmesg is sorted and uniq'd etc.
I do hope there is enough info to further this issue.
Kind regards,
Udo
next prev parent reply other threads:[~2012-12-01 8:52 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-07-08 7:53 3.4.4: disabling irq Udo van den Heuvel
2012-07-09 13:54 ` Clemens Ladisch
2012-07-09 16:05 ` Udo van den Heuvel
2012-07-09 18:58 ` Alan Stern
2012-07-11 14:50 ` Udo van den Heuvel
2012-07-11 15:15 ` Alan Stern
2012-07-12 13:23 ` Udo van den Heuvel
2012-07-12 13:43 ` Jan Ceuleers
2012-07-12 14:02 ` Udo van den Heuvel
2012-07-12 14:54 ` Alan Stern
2012-07-15 14:28 ` Udo van den Heuvel
2012-07-15 14:36 ` Udo van den Heuvel
2012-07-15 15:35 ` Alan Stern
2012-07-15 15:55 ` Udo van den Heuvel
2012-07-15 15:57 ` Udo van den Heuvel
2012-07-15 18:28 ` Alan Stern
2012-11-04 10:31 ` Udo van den Heuvel
2012-11-17 12:35 ` Udo van den Heuvel
2012-11-19 16:41 ` Alan Stern
2012-11-19 16:47 ` Udo van den Heuvel
2012-11-20 14:41 ` Udo van den Heuvel
2012-11-20 16:14 ` Alan Stern
2012-12-01 8:52 ` Udo van den Heuvel [this message]
2012-12-01 16:54 ` Alan Stern
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=50B9C545.4060808@xs4all.nl \
--to=udovdh@xs4all.nl \
--cc=clemens@ladisch.de \
--cc=jan.ceuleers@computer.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=sijones2010@gmail.com \
--cc=stern@rowland.harvard.edu \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.