Re: linux-next: manual merge of the l2-mtd tree with Linus' tree

[Murali Karicheri <m-karicheri2@ti.com>]

On 12/13/2012 12:38 AM, Kumar, Anil wrote:
> On Thu, Dec 13, 2012 at 07:07:55, Stephen Rothwell wrote:
>> Hi Artem,
>>
>> Today's linux-next merge of the l2-mtd tree got a conflict in
>> Documentation/devicetree/bindings/arm/davinci/nand.txt between commit
>> fed16bba8726 ("mtd: nand: davinci: fix the binding documentation") from
>> Linus' tree and commit 192afdbfbc5c ("mtd: davinci: add support for
>> parition binding nodes") from the l2-mtd tree.
>>
>> I fixed it up (maybe- see below) and can carry the fix as necessary (no
>> action is required).
>>
>> -- 
>> Cheers,
>> Stephen Rothwell                    sfr@canb.auug.org.au
>>
>> diff --cc Documentation/devicetree/bindings/arm/davinci/nand.txt
>> index 49fc7ad,4746452..0000000
>> --- a/Documentation/devicetree/bindings/arm/davinci/nand.txt
>> +++ b/Documentation/devicetree/bindings/arm/davinci/nand.txt
>> @@@ -23,16 -23,37 +23,24 @@@ Recommended properties
>>    - ti,davinci-nand-buswidth: buswidth 8 or 16
>>    - ti,davinci-nand-use-bbt: use flash based bad block table support.
>>
>> + nand device bindings may contain additional sub-nodes describing
>> + partitions of the address space. See partition.txt for more detail.
>> +
>>   -Example (enbw_cmc board):
>>   -aemif@60000000 {
>>   -	compatible = "ti,davinci-aemif";
>>   -	#address-cells =<2>;
>>   -	#size-cells =<1>;
>>   -	reg =<0x68000000 0x80000>;
>>   -	ranges =<2 0 0x60000000 0x02000000
>>   -		  3 0 0x62000000 0x02000000
>>   -		  4 0 0x64000000 0x02000000
>>   -		  5 0 0x66000000 0x02000000
>>   -		  6 0 0x68000000 0x02000000>;
>>   -	nand@3,0 {
>>   -		compatible = "ti,davinci-nand";
>>   -		reg =<3 0x0 0x807ff
>>   -			6 0x0 0x8000>;
>>   -		#address-cells =<1>;
>>   -		#size-cells =<1>;
>>   -		ti,davinci-chipselect =<1>;
>>   -		ti,davinci-mask-ale =<0>;
>>   -		ti,davinci-mask-cle =<0>;
>>   -		ti,davinci-mask-chipsel =<0>;
>>   -		ti,davinci-ecc-mode = "hw";
>>   -		ti,davinci-ecc-bits =<4>;
>>   -		ti,davinci-nand-use-bbt;
>>   +Example(da850 EVM ):
>>   +nand_cs3@62000000 {
>>   +	compatible = "ti,davinci-nand";
>>   +	reg =<0x62000000 0x807ff
>>   +		0x68000000 0x8000>;
>>   +	ti,davinci-chipselect =<1>;
>>   +	ti,davinci-mask-ale =<0>;
>>   +	ti,davinci-mask-cle =<0>;
>>   +	ti,davinci-mask-chipsel =<0>;
>>   +	ti,davinci-ecc-mode = "hw";
>>   +	ti,davinci-ecc-bits =<4>;
>>   +	ti,davinci-nand-use-bbt;
>> +
>>   -		partition@180000 {
>>   -			label = "ubifs";
>>   -			reg =<0x180000 0x7e80000>;
>>   -		};
>> ++	partition@180000 {
>> ++		label = "ubifs";
>> ++		reg =<0x180000 0x7e80000>;
> partition@180000 is sub-node of nand_cs3@62000000.
> nand_cs3@62000000 needs to use below properties
>
> #address-cells =<1>;
> #size-cells =<1>;
>
> Without these properties DT build will give reg format Warning.
>
>> + 	};
>>    };
>>
Anul,

Could you point me to a corresponding driver commit id?

Murali