From: Xose Vazquez Perez <xose.vazquez@gmail.com>
To: Thomas Rosenkranz <tom.rosary@googlemail.com>
Cc: linux-wireless <linux-wireless@vger.kernel.org>,
Larry Finger <Larry.Finger@lwfinger.net>
Subject: Re: FW: 0bda:819a RTL8188CUS WLAN doesn't work out of the box in downstream and upstreamkernel
Date: Tue, 05 Feb 2013 20:55:38 +0100 [thread overview]
Message-ID: <511163BA.7060902@gmail.com> (raw)
In-Reply-To: <CAOAX8-k-Nbx4Om8fkEHRW2jmZCxKpsMY6oEZMAvdEQpXWn9Mdw@mail.gmail.com>
On 02/05/2013 12:00 AM, Thomas Rosenkranz wrote:
Larry, are you able to identify the chip of that device
with the 8192cu output ?
what should he do ? open the device to see the chip ??
> [ 183.369324] rtw driver version=v3.4.4_xxxx.20120730
> [ 183.369330] Build at: Feb 4 2013 23:44:44
> [ 183.369400] usbcore: registered new interface driver rtl8192cu
> [ 183.370696] register rtw_netdev_ops to netdev_ops
> [ 183.370702] CHIP TYPE: RTL8188C_8192C
> [ 183.370706]
> [ 183.370707] usb_endpoint_descriptor(0):
> [ 183.370710] bLength=7
> [ 183.370711] bDescriptorType=5
> [ 183.370713] bEndpointAddress=81
> [ 183.370715] wMaxPacketSize=200
> [ 183.370717] bInterval=0
> [ 183.370719] RT_usb_endpoint_is_bulk_in = 1
> [ 183.370721]
> [ 183.370722] usb_endpoint_descriptor(1):
> [ 183.370724] bLength=7
> [ 183.370726] bDescriptorType=5
> [ 183.370727] bEndpointAddress=2
> [ 183.370729] wMaxPacketSize=200
> [ 183.370731] bInterval=0
> [ 183.370733] RT_usb_endpoint_is_bulk_out = 2
> [ 183.370735]
> [ 183.370736] usb_endpoint_descriptor(2):
> [ 183.370738] bLength=7
> [ 183.370739] bDescriptorType=5
> [ 183.370741] bEndpointAddress=3
> [ 183.370743] wMaxPacketSize=200
> [ 183.370744] bInterval=0
> [ 183.370746] RT_usb_endpoint_is_bulk_out = 3
> [ 183.370748]
> [ 183.370749] usb_endpoint_descriptor(3):
> [ 183.370751] bLength=7
> [ 183.370752] bDescriptorType=5
> [ 183.370754] bEndpointAddress=84
> [ 183.370756] wMaxPacketSize=40
> [ 183.370758] bInterval=1
> [ 183.370760] RT_usb_endpoint_is_int_in = 4, Interval = 1
> [ 183.370762] nr_endpoint=4, in_num=2, out_num=2
> [ 183.370764]
> [ 183.370765] USB_SPEED_HIGH
> [ 183.370905] Chip Version ID: VERSION_NORMAL_TSMC_CHIP_88C.
> [ 183.370912] RF_Type is 3!!
> [ 183.371259] EEPROM type is E-FUSE
> [ 183.371263] ====> ReadAdapterInfo8192C
> [ 183.371385] Boot from EFUSE, Autoload OK !
> [ 183.556146] EEPROMVID = 0x0bda
> [ 183.556150] EEPROMPID = 0x819a
> [ 183.556152] EEPROMCustomerID : 0x00
> [ 183.556154] EEPROMSubCustomerID: 0x00
> [ 183.556156] RT_CustomerID: 0x00
> [ 183.556159] _ReadMACAddress MAC Address from EFUSE = 00:1c:7b:a8:a8:f3
> [ 183.556163] EEPROMRegulatory = 0x1
> [ 183.556165] _ReadBoardType(3)
> [ 183.556167] BT Coexistance = disable
> [ 183.556170] RT_ChannelPlan: 0x0a
> [ 183.556172] _ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(10) ,bSupportRemoteWakeup(0)
> [ 183.556176] ### PS params=> power_mgnt(1),usbss_enable(0) ###
> [ 183.556178] ### AntDivCfg(0)
> [ 183.556180] readAdapterInfo_8192CU(): REPLACEMENT = 1
> [ 183.556184] <==== ReadAdapterInfo8192C in 184 ms
> [ 183.556432] rtw_macaddr_cfg MAC Address = 00:1c:7b:a8:a8:f3
> [ 183.556436] MAC Address from pnetdev->dev_addr= 00:1c:7b:a8:a8:f3
> [ 183.557231] bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
> [ 183.571360] bDriverStopped=1
> [ 183.572190] +871x_drv - drv_open, bup=0
> [ 183.576780] ===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC
> [ 183.576786] FirmwareDownload92C accquire FW from embedded image
> [ 183.576790] fw_ver=v80, fw_subver=0, sig=0x88c0
> [ 183.608627] fw download ok!
> [ 183.608631] Set RF Chip ID to RF_6052 and RF type to 1T1R.
> [ 183.984930] IQK:Start!!!
> [ 183.996309] Path A IQK Success!!
> [ 184.004034] Path A IQK Success!!
> [ 184.008907] IQK: final_candidate is 0
> [ 184.008911] IQK: RegE94=ff RegE9C=d RegEA4=fd RegEAC=3fd RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
> [ 184.008914] Path A IQ Calibration Success !
> [ 184.122503] pdmpriv->TxPowerTrackControl = 1
> [ 184.127472] MAC Address from REG_MACID = 00:1c:7b:a8:a8:f3
> [ 184.127476] rtl8192cu_hal_init in 556ms
> [ 184.127480] MAC Address = 00:1c:7b:a8:a8:f3
> [ 184.132257] -871x_drv - drv_open, bup=1
> [ 184.133354] ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [ 184.133824] ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [ 184.133854] set_mode = IW_MODE_INFRA
> [ 184.150748] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
> [ 184.150763] set_mode = IW_MODE_INFRA
> [ 184.193691] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
> [ 185.543612] survey done event(25)
> [ 185.593007] IW_SCAN_THIS_ESSID, ssid=nicht dein WLAN, len=15
> [ 186.942758] survey done event(2d)
> [ 186.943996] wpa_set_auth_algs, AUTH_ALG_OPEN_SYSTEM
> [ 186.944003] set_mode = IW_MODE_INFRA
> [ 186.944019]
> [ 186.944020] wpa_ie(length:22):
> [ 186.944024] 0x30 0x14 0x01 0x00 0x00 0x0f 0xac 0x02
> [ 186.944028] 0x01 0x00 0x00 0x0f 0xac 0x04 0x01 0x00
> [ 186.944031] 0x00 0x0f 0xac 0x02 0x00 0x00 0x00 0x00
> [ 186.944045] =>rtw_wx_set_essid
> [ 186.944047] ssid=nicht dein WLAN, len=15
> [ 186.944052] Set SSID under fw_state=0x00000008
> [ 186.944058] [by_bssid:0][assoc_ssid:nicht dein WLAN][to_roaming:0] new candidate: nicht dein WLAN(00:15:0c:f1:0d:d0) rssi:-32
> [ 186.944077] rtw_select_and_join_from_scanned_queue: candidate: nicht dein WLAN(00:15:0c:f1:0d:d0)
> [ 186.944090] link to new AP
> [ 186.944100] <=rtw_wx_set_essid, ret 0
> [ 186.944110] Set BSSID under fw_state=0x00000088
> [ 187.125476] link to new AP
> [ 187.125484] issue_deauth to 00:15:0c:f1:0d:d0
> [ 187.129338] OnAuthClient
> [ 187.129349] network.SupportedRates[0]=82
> [ 187.129351] network.SupportedRates[1]=84
> [ 187.129353] network.SupportedRates[2]=8B
> [ 187.129356] network.SupportedRates[3]=96
> [ 187.129358] network.SupportedRates[4]=2C
> [ 187.129360] network.SupportedRates[5]=0C
> [ 187.129362] network.SupportedRates[6]=12
> [ 187.129364] network.SupportedRates[7]=18
> [ 187.129366] network.SupportedRates[8]=24
> [ 187.129368] network.SupportedRates[9]=30
> [ 187.129370] network.SupportedRates[10]=48
> [ 187.129372] network.SupportedRates[11]=60
> [ 187.129374] network.SupportedRates[12]=6C
> [ 187.129377] issue_assocreq(): the rate[4]=2C is not supported by STA!
> [ 187.129380] bssrate_len = 12
> [ 187.135954] OnAssocRsp
> [ 187.135977] report_join_res(1)
> [ 187.135983] rtw_joinbss_update_network
> [ 187.135994] rtw_joinbss_update_stainfo
> [ 187.136060] HW_VAR_BASIC_RATE: BrateCfg(0x15d)
> [ 187.137196] HTOnAssocRsp
> [ 187.137334] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
> [ 187.142408] update raid entry, mask=0x40000fff, arg=0x80
> [ 187.143905] rtl8192c_set_FwJoinBssReport_cmd mstatus(1)
> [ 187.144776] SetFwRsvdPagePkt
> [ 187.144787] Set RSVD page location to Fw.
> [ 187.145453]
> [ 187.145455] ~~~~stastakey:unicastkey
> [ 187.145524]
> [ 187.145525] ~~~~stastakey:groupkey
> [ 187.145529] ==> rtw_set_key algorithm(2),keyid(2),key_mask(4)
> [ 187.145903] =>mlmeext_joinbss_event_callback
> [ 187.811595] rx bc/mc packets, to perform sw rtw_tkip_decrypt
> [ 188.141761] rtl8192c_dm_RF_Saving(): RF_Save
> [ 197.538636] wlan0: no IPv6 routers present
> tommy@Tommy-AIO:~$ lsusb -v -d 0bda:819a
>
> Bus 001 Device 006: ID 0bda:819a Realtek Semiconductor Corp.
> Couldn't open device, some information will be missing
> Device Descriptor:
> bLength 18
> bDescriptorType 1
> bcdUSB 2.00
> bDeviceClass 0 (Defined at Interface level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 64
> idVendor 0x0bda Realtek Semiconductor Corp.
> idProduct 0x819a
> bcdDevice 2.00
> iManufacturer 1
> iProduct 2
> iSerial 3
> bNumConfigurations 1
> Configuration Descriptor:
> bLength 9
> bDescriptorType 2
> wTotalLength 46
> bNumInterfaces 1
> bConfigurationValue 1
> iConfiguration 0
> bmAttributes 0xa0
> (Bus Powered)
> Remote Wakeup
> MaxPower 500mA
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 0
> bAlternateSetting 0
> bNumEndpoints 4
> bInterfaceClass 255 Vendor Specific Class
> bInterfaceSubClass 255 Vendor Specific Subclass
> bInterfaceProtocol 255 Vendor Specific Protocol
> iInterface 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x81 EP 1 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x02 EP 2 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x03 EP 3 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x84 EP 4 IN
> bmAttributes 3
> Transfer Type Interrupt
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0040 1x 64 bytes
> bInterval 1
next prev parent reply other threads:[~2013-02-05 19:55 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-02-04 21:41 FW: 0bda:819a RTL8188CUS WLAN doesn't work out of the box in downstream and upstreamkernel Xose Vazquez Perez
[not found] ` <CAOAX8-k-Nbx4Om8fkEHRW2jmZCxKpsMY6oEZMAvdEQpXWn9Mdw@mail.gmail.com>
2013-02-04 23:13 ` Larry Finger
2013-02-04 23:26 ` Xose Vazquez Perez
[not found] ` <CAOAX8-kFtWuwEvz9v7hBzOwtohJx0NezrDHC0iVwXF29YYSCgQ@mail.gmail.com>
2013-02-05 18:33 ` Thomas Rosenkranz
2013-02-05 19:03 ` Larry Finger
[not found] ` <CAOAX8-mMsXu5h-7q2EJEc9SehWS=yqAb4YvbfOVBQKhdH+LqTQ@mail.gmail.com>
2013-02-05 18:36 ` Fwd: " Thomas Rosenkranz
2013-02-05 19:55 ` Xose Vazquez Perez [this message]
2013-02-05 20:23 ` Larry Finger
2013-02-05 21:18 ` Thomas Rosenkranz
2013-02-05 21:28 ` Xose Vazquez Perez
2013-02-05 21:54 ` Larry Finger
2013-02-05 22:37 ` Xose Vazquez Perez
2013-02-05 23:45 ` Larry Finger
2013-02-06 0:03 ` Xose Vazquez Perez
-- strict thread matches above, loose matches on Subject: below --
2013-02-04 17:50 Thomas Rosenkranz
2013-02-04 19:49 ` Larry Finger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=511163BA.7060902@gmail.com \
--to=xose.vazquez@gmail.com \
--cc=Larry.Finger@lwfinger.net \
--cc=linux-wireless@vger.kernel.org \
--cc=tom.rosary@googlemail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.