From mboxrd@z Thu Jan 1 00:00:00 1970 Message-ID: <5112A269.40609@siemens.com> Date: Wed, 06 Feb 2013 19:35:21 +0100 From: Jan Kiszka MIME-Version: 1.0 References: <51128CE4.4020303@siemens.com> <51128E3E.808@xenomai.org> <511293EB.1080502@siemens.com> <5112945F.8080102@xenomai.org> <51129599.3080709@siemens.com> <51129693.1040400@xenomai.org> <5112974A.8050008@siemens.com> <5112982B.1020901@xenomai.org> <5112A06A.7030809@siemens.com> <5112A175.5010002@xenomai.org> In-Reply-To: <5112A175.5010002@xenomai.org> Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 7bit Subject: Re: [Xenomai] ipipe/x86: do not restore during context switch List-Id: Discussions about the Xenomai project List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , To: Gilles Chanteperdrix Cc: Xenomai On 2013-02-06 19:31, Gilles Chanteperdrix wrote: > On 02/06/2013 07:26 PM, Jan Kiszka wrote: > >> On 2013-02-06 18:51, Gilles Chanteperdrix wrote: >>> On 02/06/2013 06:47 PM, Jan Kiszka wrote: >>> >>>> On 2013-02-06 18:44, Gilles Chanteperdrix wrote: >>>>> On 02/06/2013 06:40 PM, Jan Kiszka wrote: >>>>> >>>>>> On 2013-02-06 18:35, Gilles Chanteperdrix wrote: >>>>>>> On 02/06/2013 06:33 PM, Jan Kiszka wrote: >>>>>>> >>>>>>>> On 2013-02-06 18:09, Gilles Chanteperdrix wrote: >>>>>>>>> On 02/06/2013 06:03 PM, Jan Kiszka wrote: >>>>>>>>> >>>>>>>>>> Gilles, >>>>>>>>>> >>>>>>>>>> do you remember if this core-3.4 change was a performance optimization >>>>>>>>>> or a necessary fix? Also, I'm not yet understanding why we need all the >>>>>>>>>> #ifdefs except for the first one which forces fpu.preload to 0. >>>>>>>>> >>>>>>>>> >>>>>>>>> It is a performance optimization, without it, we systematically hit the >>>>>>>>> maximum latency when the timer would tick during a context switch which >>>>>>>>> restores the FPU. Note that if you change that, you will probably break >>>>>>>>> -forge. >>>>>>>> >>>>>>>> According to the Intel folks who introduced eagerfpu, xsave, or at least >>>>>>>> xsaveopt (which I didn't implemented yet) is now faster than serializing >>>>>>>> clts/stts. On the other hand, the worst case is a full SSE + AVX restore >>>>>>>> while the target RT task is not depending on the FPU. >>>>>>> >>>>>>> >>>>>>> Without xsave, we never restore fpu if the RT task never used it. This >>>>>>> changes with xsave? >>>>>> >>>>>> This would change with eagerfpu which depends on xsave. The kernel >>>>>> sticks with lazy switching in the absence of xsaveopt. >>>>> >>>>> >>>>> I am not sure you understand what I mean, so, I am going to reformulate. >>>>> Without xsave, Linux uses lazy fpu restore, and Xenomai uses eager fpu >>>>> restore. But Xenomai eager fpu restore is a nop if the RT task never >>>>> used FPU since its inception (and all the parents from which it is >>>>> cloned never used FPU either). Does Linux eager switching mean the same >>>>> thing? >>>> >>>> eagerfpu means: always call xsaveopt/xrstor, it will optimize the case >>>> that the FPU was unused by the source/destination. And no fiddling with >>>> TS anymore, at no time. >>> >>> >>> I still do not understand this sentence then: "the worst case is a full >>> SSE + AVX restore while the target RT task is not depending on the FPU." >>> If the RT task does not depend on the FPU, why would xsaveopt/xrstor >>> restore SSE and AVX context? >> >> Switching between two tasks that both use the full state space defines >> the maximum latency of the FPU save/restore step. We cannot interrupt >> xsave or xrstor instructions, but we couldn't interrupt fxsave either. >> >> What we can do, though, is to ensure that we have at least an preemption >> point between both. Do we have such thing so far, a chance to handle a >> Xenomai IRQ between some FPU save for Linux task A and a FPU restore for >> the following task B? If not, the discussion is mood and we are just >> shifting probabilities of the very same worst case. > > > We can implement unlocked context switch support on x86 as we do on > other platforms. I tried that on atom actually and it did not really > improve latencies. You do not answer my question though, why would > xsave/xrstor do anything if the RT thread has not used FPU (and all its > parents have not used fpu) ? We first of all would have to wait for the unrelated switch between those two Linux tasks before we could handle the IRQ and switch to the FPU-free RT task. __switch_to is atomic, also for Linux->Linux, no? Jan -- Siemens AG, Corporate Technology, CT RTC ITP SDP-DE Corporate Competence Center Embedded Linux