From: Jaehoon Chung <jh80.chung@samsung.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH] mmc:sdhci:fix: Change default interrupts enabled at SDHCI initialization
Date: Fri, 22 Feb 2013 08:33:34 +0900 [thread overview]
Message-ID: <5126AECE.2020509@samsung.com> (raw)
In-Reply-To: <51265D33.8030606@ti.com>
Hi Tom,
On 02/22/2013 02:45 AM, Tom Rini wrote:
> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
>
> On 02/21/2013 12:21 PM, Lukasz Majewski wrote:
>> Dear All,
>>
>> I'd like to kindly ask for any feedback on this patch.
>>
>> It is now more than month on the u-boot mailing list...
>
> OK, sorry, the generic name of the driver threw me for a minute. I'm
> fine with this change going up u-boot-samsung -> u-boot-arm -> master
> since it's a samsung-only driver right now. Does this work for you?
I think that this driver didn't use samsung-only.
going up u-boot-samsung? I'm not sure that.
Best Regards,
Jaehoon Chung
>
>>
>>
>>> Dear All,
>>>
>>> Any feedback about this patch?
>>>
>>> It has been on the list for quite long time.....
>>>
>>>
>>>> Dear All,
>>>>
>>>> Any feedback about this patch?
>>>>
>>>>> This patch changes sdhci_init()'s behavior to NOT enable all
>>>>> interrupt sources by default. Moreover interrupt signaling
>>>>> has been disabled.
>>>>>
>>>>> This patch do not enable interrupts which aren't served in
>>>>> u-boot (they are defined at sdhci.h but NOT used elsewhere):
>>>>> - SDHCI_INT_CARD_INSERT, SDHCI_INT_CARD_REMOVE,
>>>>> SDHCI_BUS_POWER, SDHCI_INT_CARD_REMOVE, SDHCI_INT_CARD_INT
>>>>>
>>>>> Special care shall be put on SDHCI_INT_CARD_INT, which
>>>>> indicates interrupt generated by SD card. According to "SD
>>>>> Host Controller Simplified Spec. ver 3.00" when bit 8 (Card
>>>>> Interrupt Status Enable) at "Normal Interrupt Status Enable
>>>>> Register" (offset 0x34) is set, the card interrupt detection
>>>>> is started. Then eMMC card may cause the SD controller to set
>>>>> this bit and then this interrupt is passed to booted OS and
>>>>> might cause kernel crash.
>>>>>
>>>>>
>>>>> To sum up: - Only enable interrupts, which are served at
>>>>> u-boot - This cleanup as a side effect fixes SDHCI's CARD
>>>>> INTERRUPT problem at Linux kernel (versions 3.6+, sdhci
>>>>> controller) - Keep masked bits at "Normal Interrupt Signal
>>>>> Enable Register" (0x38h)
>>>>>
>>>>> Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
>>>>> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc:
>>>>> Lei Wen <leiwen@marvell.com> Cc: Andy Fleming
>>>>> <afleming@freescale.com> --- drivers/mmc/sdhci.c | 8
>>>>> +++++--- 1 files changed, 5 insertions(+), 3 deletions(-)
>>>>>
>>>>> diff --git a/drivers/mmc/sdhci.c b/drivers/mmc/sdhci.c index
>>>>> 0fd1337..76c14fb 100644 --- a/drivers/mmc/sdhci.c +++
>>>>> b/drivers/mmc/sdhci.c @@ -412,9 +412,11 @@ int
>>>>> sdhci_init(struct mmc *mmc) status = sdhci_readl(host,
>>>>> SDHCI_PRESENT_STATE); }
>>>>>
>>>>> - /* Eable all state */ - sdhci_writel(host,
>>>>> SDHCI_INT_ALL_MASK, SDHCI_INT_ENABLE); - sdhci_writel(host,
>>>>> SDHCI_INT_ALL_MASK, SDHCI_SIGNAL_ENABLE); + /* Enable only
>>>>> interrupts served by the SD controller */ +
>>>>> sdhci_writel(host, SDHCI_INT_DATA_MASK | SDHCI_INT_CMD_MASK +
>>>>> , SDHCI_INT_ENABLE); + /* Mask all sdhci interrupt sources
>>>>> */ + sdhci_writel(host, 0x0, SDHCI_SIGNAL_ENABLE);
>>>>>
>>>>> return 0; }
>>>>
>>>>
>>>>
>>>
>>>
>>>
>>
>
>
> - --
> Tom
> -----BEGIN PGP SIGNATURE-----
> Version: GnuPG v1.4.11 (GNU/Linux)
> Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/
>
> iQIcBAEBAgAGBQJRJl0zAAoJENk4IS6UOR1WU68P/RTyQMDciU5rlgA0NfcSt2/y
> T55Q+R43eaRABLqEdLu5rQXJgKcLIQZEr4Czfu3LqWDfUylJiXkUc+ngSQ/uJR9p
> v1IN+rrIOs3ZQcFy9d3oDROtkz16Mc0T+32WI8g/NfL7X9IKYqSEeBUGmc0O54Ro
> kdmH9fqzCX3wbaY//+vG1uMA3s61Ekx+3Gbf5BcyoVMHrf1fNz4L1kZ7ZB/MBzdp
> HOQIoButM7/BGteF5o5LPHCNw7LtnAz5basRwaGQmrGVzeA2GCKFOrYEx3oa/ghC
> mK/PNTW6RCzRFBckbA2No9C1Tj1i7EMy8K/B8sub9FmJWF9XfDf4YhbacXOse5RA
> +mSwZiWuJP7K/0YaDUh7itQE2Wec2iA2LNlgb0Ujwnm4DsxnP805Cbz/JJuT9mCu
> 8LYw7crg4DwU9X0g0MEojKXupQ2mHMBHHrYRuUdIaYxHkkkf7j4mSIzPR75FzAjF
> 8l54TL4bEKHyUd7HmTaEkafyhziC8Kit4SEQqjTJW9S720nVOaM/pMmrji3mxUXH
> wHUpTTVS0TIAzhdAtxxpPxbRsMnnEgobOFGDbF8wzjGMQWWudZGLXqCm0kv+5B2K
> 3o6IlxPQ/TlokPe+A63NHTbJTJ0z/ylLX0UyNifzPzsoTiskO4qqSdHdrGTcA3f+
> Tqq0rAM0CXj2oMMkkOFb
> =nGWo
> -----END PGP SIGNATURE-----
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
next prev parent reply other threads:[~2013-02-21 23:33 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-01-11 15:08 [U-Boot] [PATCH] mmc:sdhci:fix: Change default interrupts enabled at SDHCI initialization Lukasz Majewski
2013-01-29 14:47 ` Lukasz Majewski
2013-01-30 4:52 ` Jaehoon Chung
2013-02-11 8:50 ` Lukasz Majewski
2013-02-11 13:58 ` Tom Rini
2013-02-21 17:21 ` Lukasz Majewski
2013-02-21 17:45 ` Tom Rini
2013-02-21 23:33 ` Jaehoon Chung [this message]
2013-02-21 23:43 ` Tom Rini
2013-02-22 7:11 ` Lukasz Majewski
2013-02-22 7:41 ` Jaehoon Chung
2013-03-11 8:22 ` Lukasz Majewski
2013-03-12 10:54 ` Minkyu Kang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5126AECE.2020509@samsung.com \
--to=jh80.chung@samsung.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.