From: Jon Hunter <jon-hunter@ti.com>
To: Rob Herring <robherring2@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>,
Tony Lindgren <tony@atomide.com>,
Benoit Cousson <b-cousson@ti.com>,
device-tree <devicetree-discuss@lists.ozlabs.org>,
linux-omap <linux-omap@vger.kernel.org>,
Mark Jackson <mpfj-list@mimc.co.uk>,
linux-arm <linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH V3 12/18] ARM: OMAP2+: Add additional GPMC timing parameters
Date: Mon, 18 Mar 2013 09:32:50 -0500 [thread overview]
Message-ID: <51472592.4030402@ti.com> (raw)
In-Reply-To: <51471F8D.4060608@gmail.com>
On 03/18/2013 09:07 AM, Rob Herring wrote:
> On 03/15/2013 10:21 AM, Jon Hunter wrote:
>> Some of the GPMC timings parameters are currently missing from the GPMC
>> device-tree binding. Add these parameters to the binding documentation
>> as well as code to read them.
>>
>> The existing code in gpmc_read_timings_dt() is checking the value of
>> of_property_read_u32() and only is successful storing the value read
>> in the gpmc_timings structure. Checking the return value in this case
>> is not necessary and we can simply read the value, if present, and
>> store directly in the gpmc_timings structure. Therefore, simplify the
>> code by removing these checks.
>>
>> The comment in the gpmc_read_timings_dt() function, "only for OMAP3430"
>> is also incorrect as it is applicable to all OMAP3+ devices. So correct
>> this too.
>>
>> Signed-off-by: Jon Hunter <jon-hunter@ti.com>
>> ---
>> Documentation/devicetree/bindings/bus/ti-gpmc.txt | 25 +++++-
>> arch/arm/mach-omap2/gpmc.c | 93 ++++++++++-----------
>> 2 files changed, 66 insertions(+), 52 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/Documentation/devicetree/bindings/bus/ti-gpmc.txt
>> index 6fde1cf..a63bd93 100644
>> --- a/Documentation/devicetree/bindings/bus/ti-gpmc.txt
>> +++ b/Documentation/devicetree/bindings/bus/ti-gpmc.txt
>> @@ -56,10 +56,27 @@ Timing properties for child nodes. All are optional and default to 0.
>> - gpmc,oe-off: Deassertion time
>>
>> Access time and cycle time timings corresponding to GPMC_CONFIG5:
>> - - gpmc,page-burst-access: Multiple access word delay
>> - - gpmc,access: Start-cycle to first data valid delay
>> - - gpmc,rd-cycle: Total read cycle time
>> - - gpmc,wr-cycle: Total write cycle time
>> + - gpmc,page-burst-access: Multiple access word delay
>> + - gpmc,access: Start-cycle to first data valid delay
>> + - gpmc,rd-cycle: Total read cycle time
>> + - gpmc,wr-cycle: Total write cycle time
>> + - gpmc,bus-turnaround: Turn-around time between successive accesses
>> + - gpmc,cycle2cycle-delay: Delay between chip-select pulses
>> + - gpmc,clk-activation: GPMC clock activation time
>> + - gpmc,wait-monitoring: Start of wait monitoring with regard to valid
>> + data
>
> What units are these in? If in nanoseconds, can you append "-ns"
These are cycles. I can update the comment to reflect that.
>> +
>> +Boolean timing parameters. If property is present parameter enabled and
>> +disabled if omitted:
>> + - gpmc,adv-extra-delay: ADV signal is delayed by half GPMC clock
>> + - gpmc,cs-extra-delay: CS signal is delayed by half GPMC clock
>> + - gpmc,cycle2cycle-diffcsen: Add "cycle2cycle-delay" between successive
>> + accesses to a different CS
>> + - gpmc,cycle2cycle-samecsen: Add "cycle2cycle-delay" between successive
>> + accesses to the same CS
>> + - gpmc,oe-extra-delay: OE signal is delayed by half GPMC clock
>> + - gpmc,we-extra-delay: WE signal is delayed by half GPMC clock
>> + - gpmc,time-para-granularity: Multiply all access times by 2
>>
>> The following are only applicable to OMAP3+ and AM335x:
>> - gpmc,wr-access
>> diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c
>> index 85b1a35..c928a8c 100644
>> --- a/arch/arm/mach-omap2/gpmc.c
>> +++ b/arch/arm/mach-omap2/gpmc.c
>> @@ -1274,67 +1274,64 @@ void gpmc_read_settings_dt(struct device_node *np, struct gpmc_settings *p)
>> static void __maybe_unused gpmc_read_timings_dt(struct device_node *np,
>> struct gpmc_timings *gpmc_t)
>> {
>> - u32 val;
>> -
>> memset(gpmc_t, 0, sizeof(*gpmc_t));
>>
>> /* minimum clock period for syncronous mode */
>> - if (!of_property_read_u32(np, "gpmc,sync-clk", &val))
>> - gpmc_t->sync_clk = val;
>> + of_property_read_u32(np, "gpmc,sync-clk", &gpmc_t->sync_clk);
>>
>> /* chip select timtings */
>> - if (!of_property_read_u32(np, "gpmc,cs-on", &val))
>> - gpmc_t->cs_on = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,cs-rd-off", &val))
>> - gpmc_t->cs_rd_off = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,cs-wr-off", &val))
>> - gpmc_t->cs_wr_off = val;
>> + of_property_read_u32(np, "gpmc,cs-on", &gpmc_t->cs_on);
>> + of_property_read_u32(np, "gpmc,cs-rd-off", &gpmc_t->cs_rd_off);
>> + of_property_read_u32(np, "gpmc,cs-wr-off", &gpmc_t->cs_wr_off);
>>
>> /* ADV signal timings */
>> - if (!of_property_read_u32(np, "gpmc,adv-on", &val))
>> - gpmc_t->adv_on = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,adv-rd-off", &val))
>> - gpmc_t->adv_rd_off = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,adv-wr-off", &val))
>> - gpmc_t->adv_wr_off = val;
>> + of_property_read_u32(np, "gpmc,adv-on", &gpmc_t->adv_on);
>> + of_property_read_u32(np, "gpmc,adv-rd-off", &gpmc_t->adv_rd_off);
>> + of_property_read_u32(np, "gpmc,adv-wr-off", &gpmc_t->adv_wr_off);
>>
>> /* WE signal timings */
>> - if (!of_property_read_u32(np, "gpmc,we-on", &val))
>> - gpmc_t->we_on = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,we-off", &val))
>> - gpmc_t->we_off = val;
>> + of_property_read_u32(np, "gpmc,we-on", &gpmc_t->we_on);
>> + of_property_read_u32(np, "gpmc,we-off", &gpmc_t->we_off);
>>
>> /* OE signal timings */
>> - if (!of_property_read_u32(np, "gpmc,oe-on", &val))
>> - gpmc_t->oe_on = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,oe-off", &val))
>> - gpmc_t->oe_off = val;
>> + of_property_read_u32(np, "gpmc,oe-on", &gpmc_t->oe_on);
>> + of_property_read_u32(np, "gpmc,oe-off", &gpmc_t->oe_off);
>>
>> /* access and cycle timings */
>> - if (!of_property_read_u32(np, "gpmc,page-burst-access", &val))
>> - gpmc_t->page_burst_access = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,access", &val))
>> - gpmc_t->access = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,rd-cycle", &val))
>> - gpmc_t->rd_cycle = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,wr-cycle", &val))
>> - gpmc_t->wr_cycle = val;
>> -
>> - /* only for OMAP3430 */
>> - if (!of_property_read_u32(np, "gpmc,wr-access", &val))
>> - gpmc_t->wr_access = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,wr-data-mux-bus", &val))
>> - gpmc_t->wr_data_mux_bus = val;
>> + of_property_read_u32(np, "gpmc,page-burst-access",
>> + &gpmc_t->page_burst_access);
>> + of_property_read_u32(np, "gpmc,access", &gpmc_t->access);
>> + of_property_read_u32(np, "gpmc,rd-cycle", &gpmc_t->rd_cycle);
>> + of_property_read_u32(np, "gpmc,wr-cycle", &gpmc_t->wr_cycle);
>> + of_property_read_u32(np, "gpmc,bus-turnaround",
>> + &gpmc_t->bus_turnaround);
>> + of_property_read_u32(np, "gpmc,cycle2cycle-delay",
>> + &gpmc_t->cycle2cycle_delay);
>> + of_property_read_u32(np, "gpmc,wait-monitoring",
>> + &gpmc_t->wait_monitoring);
>> + of_property_read_u32(np, "gpmc,clk-activation",
>> + &gpmc_t->clk_activation);
>> +
>> + /* only applicable to OMAP3+ */
>> + of_property_read_u32(np, "gpmc,wr-access", &gpmc_t->wr_access);
>> + of_property_read_u32(np, "gpmc,wr-data-mux-bus",
>> + &gpmc_t->wr_data_mux_bus);
>> +
>> + /* bool timing parameters */
>> + if (of_find_property(np, "gpmc,cycle2cycle-diffcsen", NULL))
>> + gpmc_t->bool_timings.cycle2cyclediffcsen = true;
>> + if (of_find_property(np, "gpmc,cycle2cycle-samecsen", NULL))
>> + gpmc_t->bool_timings.cycle2cyclesamecsen = true;
>> + if (of_find_property(np, "gpmc,we-extra-delay", NULL))
>> + gpmc_t->bool_timings.we_extra_delay = true;
>> + if (of_find_property(np, "gpmc,oe-extra-delay", NULL))
>> + gpmc_t->bool_timings.oe_extra_delay = true;
>> + if (of_find_property(np, "gpmc,adv-extra-delay", NULL))
>> + gpmc_t->bool_timings.adv_extra_delay = true;
>> + if (of_find_property(np, "gpmc,cs-extra-delay", NULL))
>> + gpmc_t->bool_timings.cs_extra_delay = true;
>> + if (of_find_property(np, "gpmc,time-para-granularity", NULL))
>> + gpmc_t->bool_timings.time_para_granularity = true;
>
> of_property_read_bool doesn't work for these?
It should work fine, I wasn't aware of that. Will change.
Cheers
Jon
WARNING: multiple messages have this Message-ID (diff)
From: jon-hunter@ti.com (Jon Hunter)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH V3 12/18] ARM: OMAP2+: Add additional GPMC timing parameters
Date: Mon, 18 Mar 2013 09:32:50 -0500 [thread overview]
Message-ID: <51472592.4030402@ti.com> (raw)
In-Reply-To: <51471F8D.4060608@gmail.com>
On 03/18/2013 09:07 AM, Rob Herring wrote:
> On 03/15/2013 10:21 AM, Jon Hunter wrote:
>> Some of the GPMC timings parameters are currently missing from the GPMC
>> device-tree binding. Add these parameters to the binding documentation
>> as well as code to read them.
>>
>> The existing code in gpmc_read_timings_dt() is checking the value of
>> of_property_read_u32() and only is successful storing the value read
>> in the gpmc_timings structure. Checking the return value in this case
>> is not necessary and we can simply read the value, if present, and
>> store directly in the gpmc_timings structure. Therefore, simplify the
>> code by removing these checks.
>>
>> The comment in the gpmc_read_timings_dt() function, "only for OMAP3430"
>> is also incorrect as it is applicable to all OMAP3+ devices. So correct
>> this too.
>>
>> Signed-off-by: Jon Hunter <jon-hunter@ti.com>
>> ---
>> Documentation/devicetree/bindings/bus/ti-gpmc.txt | 25 +++++-
>> arch/arm/mach-omap2/gpmc.c | 93 ++++++++++-----------
>> 2 files changed, 66 insertions(+), 52 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/Documentation/devicetree/bindings/bus/ti-gpmc.txt
>> index 6fde1cf..a63bd93 100644
>> --- a/Documentation/devicetree/bindings/bus/ti-gpmc.txt
>> +++ b/Documentation/devicetree/bindings/bus/ti-gpmc.txt
>> @@ -56,10 +56,27 @@ Timing properties for child nodes. All are optional and default to 0.
>> - gpmc,oe-off: Deassertion time
>>
>> Access time and cycle time timings corresponding to GPMC_CONFIG5:
>> - - gpmc,page-burst-access: Multiple access word delay
>> - - gpmc,access: Start-cycle to first data valid delay
>> - - gpmc,rd-cycle: Total read cycle time
>> - - gpmc,wr-cycle: Total write cycle time
>> + - gpmc,page-burst-access: Multiple access word delay
>> + - gpmc,access: Start-cycle to first data valid delay
>> + - gpmc,rd-cycle: Total read cycle time
>> + - gpmc,wr-cycle: Total write cycle time
>> + - gpmc,bus-turnaround: Turn-around time between successive accesses
>> + - gpmc,cycle2cycle-delay: Delay between chip-select pulses
>> + - gpmc,clk-activation: GPMC clock activation time
>> + - gpmc,wait-monitoring: Start of wait monitoring with regard to valid
>> + data
>
> What units are these in? If in nanoseconds, can you append "-ns"
These are cycles. I can update the comment to reflect that.
>> +
>> +Boolean timing parameters. If property is present parameter enabled and
>> +disabled if omitted:
>> + - gpmc,adv-extra-delay: ADV signal is delayed by half GPMC clock
>> + - gpmc,cs-extra-delay: CS signal is delayed by half GPMC clock
>> + - gpmc,cycle2cycle-diffcsen: Add "cycle2cycle-delay" between successive
>> + accesses to a different CS
>> + - gpmc,cycle2cycle-samecsen: Add "cycle2cycle-delay" between successive
>> + accesses to the same CS
>> + - gpmc,oe-extra-delay: OE signal is delayed by half GPMC clock
>> + - gpmc,we-extra-delay: WE signal is delayed by half GPMC clock
>> + - gpmc,time-para-granularity: Multiply all access times by 2
>>
>> The following are only applicable to OMAP3+ and AM335x:
>> - gpmc,wr-access
>> diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c
>> index 85b1a35..c928a8c 100644
>> --- a/arch/arm/mach-omap2/gpmc.c
>> +++ b/arch/arm/mach-omap2/gpmc.c
>> @@ -1274,67 +1274,64 @@ void gpmc_read_settings_dt(struct device_node *np, struct gpmc_settings *p)
>> static void __maybe_unused gpmc_read_timings_dt(struct device_node *np,
>> struct gpmc_timings *gpmc_t)
>> {
>> - u32 val;
>> -
>> memset(gpmc_t, 0, sizeof(*gpmc_t));
>>
>> /* minimum clock period for syncronous mode */
>> - if (!of_property_read_u32(np, "gpmc,sync-clk", &val))
>> - gpmc_t->sync_clk = val;
>> + of_property_read_u32(np, "gpmc,sync-clk", &gpmc_t->sync_clk);
>>
>> /* chip select timtings */
>> - if (!of_property_read_u32(np, "gpmc,cs-on", &val))
>> - gpmc_t->cs_on = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,cs-rd-off", &val))
>> - gpmc_t->cs_rd_off = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,cs-wr-off", &val))
>> - gpmc_t->cs_wr_off = val;
>> + of_property_read_u32(np, "gpmc,cs-on", &gpmc_t->cs_on);
>> + of_property_read_u32(np, "gpmc,cs-rd-off", &gpmc_t->cs_rd_off);
>> + of_property_read_u32(np, "gpmc,cs-wr-off", &gpmc_t->cs_wr_off);
>>
>> /* ADV signal timings */
>> - if (!of_property_read_u32(np, "gpmc,adv-on", &val))
>> - gpmc_t->adv_on = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,adv-rd-off", &val))
>> - gpmc_t->adv_rd_off = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,adv-wr-off", &val))
>> - gpmc_t->adv_wr_off = val;
>> + of_property_read_u32(np, "gpmc,adv-on", &gpmc_t->adv_on);
>> + of_property_read_u32(np, "gpmc,adv-rd-off", &gpmc_t->adv_rd_off);
>> + of_property_read_u32(np, "gpmc,adv-wr-off", &gpmc_t->adv_wr_off);
>>
>> /* WE signal timings */
>> - if (!of_property_read_u32(np, "gpmc,we-on", &val))
>> - gpmc_t->we_on = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,we-off", &val))
>> - gpmc_t->we_off = val;
>> + of_property_read_u32(np, "gpmc,we-on", &gpmc_t->we_on);
>> + of_property_read_u32(np, "gpmc,we-off", &gpmc_t->we_off);
>>
>> /* OE signal timings */
>> - if (!of_property_read_u32(np, "gpmc,oe-on", &val))
>> - gpmc_t->oe_on = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,oe-off", &val))
>> - gpmc_t->oe_off = val;
>> + of_property_read_u32(np, "gpmc,oe-on", &gpmc_t->oe_on);
>> + of_property_read_u32(np, "gpmc,oe-off", &gpmc_t->oe_off);
>>
>> /* access and cycle timings */
>> - if (!of_property_read_u32(np, "gpmc,page-burst-access", &val))
>> - gpmc_t->page_burst_access = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,access", &val))
>> - gpmc_t->access = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,rd-cycle", &val))
>> - gpmc_t->rd_cycle = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,wr-cycle", &val))
>> - gpmc_t->wr_cycle = val;
>> -
>> - /* only for OMAP3430 */
>> - if (!of_property_read_u32(np, "gpmc,wr-access", &val))
>> - gpmc_t->wr_access = val;
>> -
>> - if (!of_property_read_u32(np, "gpmc,wr-data-mux-bus", &val))
>> - gpmc_t->wr_data_mux_bus = val;
>> + of_property_read_u32(np, "gpmc,page-burst-access",
>> + &gpmc_t->page_burst_access);
>> + of_property_read_u32(np, "gpmc,access", &gpmc_t->access);
>> + of_property_read_u32(np, "gpmc,rd-cycle", &gpmc_t->rd_cycle);
>> + of_property_read_u32(np, "gpmc,wr-cycle", &gpmc_t->wr_cycle);
>> + of_property_read_u32(np, "gpmc,bus-turnaround",
>> + &gpmc_t->bus_turnaround);
>> + of_property_read_u32(np, "gpmc,cycle2cycle-delay",
>> + &gpmc_t->cycle2cycle_delay);
>> + of_property_read_u32(np, "gpmc,wait-monitoring",
>> + &gpmc_t->wait_monitoring);
>> + of_property_read_u32(np, "gpmc,clk-activation",
>> + &gpmc_t->clk_activation);
>> +
>> + /* only applicable to OMAP3+ */
>> + of_property_read_u32(np, "gpmc,wr-access", &gpmc_t->wr_access);
>> + of_property_read_u32(np, "gpmc,wr-data-mux-bus",
>> + &gpmc_t->wr_data_mux_bus);
>> +
>> + /* bool timing parameters */
>> + if (of_find_property(np, "gpmc,cycle2cycle-diffcsen", NULL))
>> + gpmc_t->bool_timings.cycle2cyclediffcsen = true;
>> + if (of_find_property(np, "gpmc,cycle2cycle-samecsen", NULL))
>> + gpmc_t->bool_timings.cycle2cyclesamecsen = true;
>> + if (of_find_property(np, "gpmc,we-extra-delay", NULL))
>> + gpmc_t->bool_timings.we_extra_delay = true;
>> + if (of_find_property(np, "gpmc,oe-extra-delay", NULL))
>> + gpmc_t->bool_timings.oe_extra_delay = true;
>> + if (of_find_property(np, "gpmc,adv-extra-delay", NULL))
>> + gpmc_t->bool_timings.adv_extra_delay = true;
>> + if (of_find_property(np, "gpmc,cs-extra-delay", NULL))
>> + gpmc_t->bool_timings.cs_extra_delay = true;
>> + if (of_find_property(np, "gpmc,time-para-granularity", NULL))
>> + gpmc_t->bool_timings.time_para_granularity = true;
>
> of_property_read_bool doesn't work for these?
It should work fine, I wasn't aware of that. Will change.
Cheers
Jon
next prev parent reply other threads:[~2013-03-18 14:33 UTC|newest]
Thread overview: 54+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-03-15 15:20 [PATCH V3 00/18] ARM: OMAP2+: GPMC clean-up and DT update Jon Hunter
2013-03-15 15:20 ` Jon Hunter
2013-03-15 15:20 ` [PATCH V3 01/18] ARM: OMAP2+: Simplify code configuring ONENAND devices Jon Hunter
2013-03-15 15:20 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 02/18] ARM: OMAP2+: Add variable to store number of GPMC waitpins Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-16 20:59 ` Ezequiel Garcia
2013-03-16 20:59 ` Ezequiel Garcia
2013-03-18 13:43 ` Jon Hunter
2013-03-18 13:43 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 03/18] ARM: OMAP2+: Add structure for storing GPMC settings Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 04/18] ARM: OMAP2+: Add function for configuring " Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 05/18] ARM: OMAP2+: Convert ONENAND to use gpmc_cs_program_settings() Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 06/18] ARM: OMAP2+: Convert NAND " Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 07/18] ARM: OMAP2+: Convert SMC91x " Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 08/18] ARM: OMAP2+: Convert TUSB " Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 09/18] ARM: OMAP2+: Don't configure of chip-select options in gpmc_cs_configure() Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 10/18] ARM: OMAP2+: Add function to read GPMC settings from device-tree Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-17 5:24 ` Ezequiel Garcia
2013-03-17 5:24 ` Ezequiel Garcia
2013-03-18 13:43 ` Jon Hunter
2013-03-18 13:43 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 11/18] ARM: OMAP2+: Add device-tree support for NOR flash Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 12/18] ARM: OMAP2+: Add additional GPMC timing parameters Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-18 14:07 ` Rob Herring
2013-03-18 14:07 ` Rob Herring
2013-03-18 14:32 ` Jon Hunter [this message]
2013-03-18 14:32 ` Jon Hunter
2013-03-18 15:59 ` Jon Hunter
2013-03-18 15:59 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 13/18] ARM: OMAP2+: Convert NAND to retrieve GPMC settings from DT Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 14/18] ARM: OMAP2+: Convert ONENAND " Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 15/18] ARM: OMAP2+: Detect incorrectly aligned GPMC base address Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 16/18] ARM: OMAP2+: Remove unnecesssary GPMC definitions and variable Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 17/18] ARM: OMAP2+: Allow GPMC probe to complete even if CS mapping fails Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-15 15:21 ` [PATCH V3 18/18] ARM: OMAP2+: return -ENODEV if GPMC child device creation fails Jon Hunter
2013-03-15 15:21 ` Jon Hunter
2013-03-17 5:34 ` [PATCH V3 00/18] ARM: OMAP2+: GPMC clean-up and DT update Ezequiel Garcia
2013-03-17 5:34 ` Ezequiel Garcia
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=51472592.4030402@ti.com \
--to=jon-hunter@ti.com \
--cc=b-cousson@ti.com \
--cc=devicetree-discuss@lists.ozlabs.org \
--cc=grant.likely@secretlab.ca \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
--cc=mpfj-list@mimc.co.uk \
--cc=robherring2@gmail.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.