Query on pinctrl usage for DT nodes

[swarren@wwwdotorg.org (Stephen Warren)]

On 04/08/2013 07:12 AM, Prabhakar Lad wrote:
> On Wed, Apr 3, 2013 at 10:14 PM, Stephen Warren <swarren@wwwdotorg.org> wrote:
>> On 04/03/2013 03:16 AM, Prabhakar Lad wrote:
>>> Hi Linus/Stephen,
>>>
>>> I am working adding  DT nodes for DA850.
...
>>> But while booting I see the following boot log:-
>>> ...
>>> cpuidle: using governor menu
>>> TCP: cubic registered
>>> NET: Registered protocol family 17
>>> pinctrl-single 1c14120.pinmux: pin 1c14130 already requested by
>>> davinci_mdio.0; cannot claim for i2c_davinci.1
>>> pinctrl-single 1c14120.pinmux: pin-4 (i2c_davinci.1) status -22
>>> pinctrl-single 1c14120.pinmux: could not request pin 4 on device pinctrl-single
>>> console [netcon0] enabled
>>> ....
>>>
>>> This is because the mdio and i2c are using same pin 0x10,
>>
>> How can two devices use the same pin? I mean physically, in hardware?
>>
>> Is this because pinctrl-single uses the register address as the pin
>> number, whereas you have registers which configure multiple pins at
> 
> Yes you are correct, we have registers  which configure multiple pins at once.
> For example for above Pin Multiplexing Control 4 Register (Pinmux4)
> [1] page(250) : -
> 
> PINMUX4_31_28 --> SP1_SCS[2]/UART1_TXD/SATA_CP_POD/GP1[0] Control
> PINMUX4_27_24 --> SPI1_SCS[3]/UART1_RXD/SATA_LED/GP1[1] Control
> PINMUX4_23_20 --> SPI1_SCS[4]/UART2_TXD/I2C1_SDA/GP1[2] Control
> PINMUX4_19_16 --> SPI1_SCS[5]/UART2_RXD/I2C1_SCL/GP1[3] Control
> PINMUX4_15_12 --> SPI1_SCS[6]/I2C0_SDA/TM64P3_OUT12/GP1[4] Control
> PINMUX4_11_8 --> SPI1_SCS[7]/I2C0_SCL/TM64P2_OUT12/GP1[5] Control
> PINMUX4_7_4 --> SPI0_SCS[0]/TM64P1_OUT12/GP1[6]/MDIO_D/TM64P1_IN12 Control
> PINMUX4_3_0 --> SPI0_SCS[1]/TM64P0_OUT12/GP1[7]/MDIO_CLK/TM64P0_IN12 Control
> 
>> once? If so, your hardware isn't something that can be represented by
>> pinctrl-single.
>
> What is the alternative for such case ? any pointer would be helpful.
> 
> [1] http://www.ti.com/general/docs/lit/getliterature.tsp?literatureNumber=spruh77a&fileType=pdf

Tony previously replied:

Tony wrote:
> Tony wrote:
>> ??? wrote:
>>> Prabhakar wrote:
>>>> Is there any
>>>> alternative way to handle if the two node's are using same pins any
>>>> pointers could be very much helpful ?
>>
>> It could also that the mux register(s) follow the one-mux-per-bit
>> mapping.
>>
>> In that case pinctrl-single,bits option as documented in the
>> Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt.
> 
> Oh it's already using pinctrl-single,bits option. Maybe there's a
> bug, adding Peter to cc.

So I guess you need to debug the code to see why that option isn't
working for you.

Going back to your original question above though, if the pinctrl-single
driver doesn't work out for you, then you'd need to create a custom
pinctrl driver for your chip, just like the many examples already in
drivers/pinctrl.