From: Yegor Yefremov <yegor_sub1@visionsystems.de>
To: "linux-omap@vger.kernel.org" <linux-omap@vger.kernel.org>
Cc: "Shilimkar, Santosh" <santosh.shilimkar@ti.com>,
"Mark A. Greer" <mgreer@animalcreek.com>,
Maxim Podbereznyy <lisarden@gmail.com>
Subject: am3517: failed to boot 3.10-rc1
Date: Tue, 14 May 2013 11:24:44 +0200 [thread overview]
Message-ID: <519202DC.10100@visionsystems.de> (raw)
Trying to boot 3.10-rc1 on an am3515 based board. With the same .config as 3.7 the system comes to RTC stops there. I've also tried make omap2plus_defconfig with no visible difference. I'm booting from MMC card and it will be detected by the system. Kernel is from http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git, latest commit f722406faae2d073cc1d01063d1123c35425939e. Are there any pending patches needed to boot on am3517?
Here bootlog:
Booting from mmc ...
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.10.0-rc1-dirty
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3750728 Bytes = 3.6 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.10.0-rc1-dirty (YegorYefremov@development1) (gcc version 4.5.3 (Buildroot 2012.05-rc2-00022-g339098e) ) #27 SMP Tue May 14 11:10:08 CEST 2013
[ 0.000000] CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: OMAP3517/AM3517 EVM
[ 0.000000] Ignoring tag cmdline (using the default kernel command line)
[ 0.000000] cma: CMA: reserved 16 MiB at 8e800000
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] AM3517 ES1.1 (l2cache sgx neon )
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c0ecd000 s13632 r8192 d15040 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768
[ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootwait console=ttyO2,115200 nohlt
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 255MB = 255MB total
[ 0.000000] Memory: 229308k/229308k available, 32836k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0689084 (6661 kB)
[ 0.000000] .init : 0xc068a000 - 0xc06e2540 ( 354 kB)
[ 0.000000] .data : 0xc06e4000 - 0xc0764f68 ( 516 kB)
[ 0.000000] .bss : 0xc0764f68 - 0xc0cc6b58 (5511 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
[ 0.000000] OMAP clockevent source: timer1 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3695 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 0.001464] Calibrating delay loop... 329.31 BogoMIPS (lpj=1646592)
[ 0.119567] pid_max: default: 32768 minimum: 301
[ 0.120330] Security Framework initialized
[ 0.120544] Mount-cache hash table entries: 512
[ 0.125946] CPU: Testing write buffer coherency: ok
[ 0.128051] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.128204] Setting up static identity map for 0xc04a99c8 - 0xc04a9a20
[ 0.133209] Brought up 1 CPUs
[ 0.133270] SMP: Total of 1 processors activated (329.31 BogoMIPS).
[ 0.133270] CPU: All CPU(s) started in SVC mode.
[ 0.137817] devtmpfs: initialized
[ 0.205139] pinctrl core: initialized pinctrl subsystem
[ 0.212188] regulator-dummy: no parameters
[ 0.217559] NET: Registered protocol family 16
[ 0.230255] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.233306] omap-gpmc omap-gpmc: GPMC revision 5.0
[ 0.249542] OMAP GPIO hardware version 2.5
[ 0.276336] omap_mux_init: Add partition: #1: core, flags: 4
[ 0.296539] omap_mux_get_by_name: Could not find signal uart4_rx.uart4_rx
[ 0.305114] Reprogramming SDRC clock to 332000000 Hz
[ 0.314483] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.336059] OMAP DMA hardware revision 4.0
[ 0.341400] arm-pmu: alias fck already exists
[ 0.428009] bio: create slab <bio-0> at 0
[ 0.555541] omap-dma-engine omap-dma-engine: OMAP DMA engine driver
[ 0.557830] hsusb1_reset: 3300 mV
[ 0.570617] SCSI subsystem initialized
[ 0.580078] omap_i2c omap_i2c.1: bus 1 rev3.3 at 400 kHz
[ 0.584442] omap_i2c omap_i2c.2: bus 2 rev3.3 at 400 kHz
[ 0.588378] omap_i2c omap_i2c.3: bus 3 rev3.3 at 400 kHz
[ 0.600799] Switching to clocksource 32k_counter
[ 0.820800] NET: Registered protocol family 2
[ 0.824340] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.824645] TCP bind hash table entries: 2048 (order: 4, 73728 bytes)
[ 0.826019] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.826416] TCP: reno registered
[ 0.826477] UDP hash table entries: 256 (order: 2, 20480 bytes)
[ 0.826873] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[ 0.829101] NET: Registered protocol family 1
[ 0.832214] RPC: Registered named UNIX socket transport module.
[ 0.832275] RPC: Registered udp transport module.
[ 0.832275] RPC: Registered tcp transport module.
[ 0.832305] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.833953] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.834472] CPU PMU: probing PMU on CPU 0
[ 0.834533] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[ 1.104064] VFS: Disk quotas dquot_6.5.2
[ 1.104431] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.108551] NFS: Registering the id_resolver key type
[ 1.109283] Key type id_resolver registered
[ 1.109313] Key type id_legacy registered
[ 1.109558] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.110443] msgmni has been set to 479
[ 1.116119] io scheduler noop registered
[ 1.116149] io scheduler deadline registered
[ 1.116271] io scheduler cfq registered (default)
[ 1.118896] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.131408] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 88) is a OMAP UART0
[ 1.135284] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 89) is a OMAP UART1
[ 1.138183] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 90) is a OMAP UART2
[ 1.769134] console [ttyO2] enabled
[ 1.775909] omap_uart.3: ttyO3 at MMIO 0x4809e000 (irq = 100) is a OMAP UART3
[ 1.834869] brd: module loaded
[ 1.868225] loop: module loaded
[ 1.879669] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.911224] mousedev: PS/2 mouse device common for all mice
[ 1.940277] rtc-s35390a 1-0030: rtc core: registered rtc-s35390a as rtc0
[ 1.948974] i2c /dev entries driver
[ 1.959381] Driver for 1-wire Dallas network protocol.
[ 1.972198] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[ 1.985198] omap-dma-engine omap-dma-engine: allocating channel for 62
[ 1.992523] omap-dma-engine omap-dma-engine: allocating channel for 61
[ 2.043548] omap-dma-engine omap-dma-engine: allocating channel for 48
[ 2.050506] omap-dma-engine omap-dma-engine: allocating channel for 47
[ 2.091613] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 2.103668] mmc0: new high speed SD card at address 0007
[ 2.115600] mmcblk0: mmc0:0007 SD02G 1.84 GiB
[ 2.129333] oprofile: using arm/armv7
[ 2.135131] TCP: cubic registered
[ 2.138641] Initializing XFRM netlink socket
[ 2.143707] NET: Registered protocol family 17
[ 2.148559] NET: Registered protocol family 15
[ 2.153991] Key type dns_resolver registered
[ 2.158630] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
[ 2.177581] voltdm_scale: No voltage scale API registered for vdd_mpu_iva
[ 2.184906] voltdm_scale: No voltage scale API registered for vdd_core
[ 2.193328] mmcblk0: p1 p2
[ 2.200012] PM: no software I/O chain control; some wakeups may be lost
[ 2.207855] ThumbEE CPU extension supported.
[ 2.212615] Registering SWP/SWPB emulation handler
[ 2.236633] rtc-s35390a 1-0030: setting system clock to 2000-01-01 01:20:01 UTC (946689601)
Yegor
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next reply other threads:[~2013-05-14 9:51 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-05-14 9:24 Yegor Yefremov [this message]
2013-05-14 12:52 ` am3517: failed to boot 3.10-rc1 Felipe Balbi
2013-05-14 13:01 ` Yegor Yefremov
2013-05-15 8:37 ` Yegor Yefremov
2013-05-15 9:31 ` Yegor Yefremov
2013-05-16 18:12 ` Tony Lindgren
2013-05-17 16:51 ` Kevin Hilman
2013-05-21 8:27 ` Yegor Yefremov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=519202DC.10100@visionsystems.de \
--to=yegor_sub1@visionsystems.de \
--cc=linux-omap@vger.kernel.org \
--cc=lisarden@gmail.com \
--cc=mgreer@animalcreek.com \
--cc=santosh.shilimkar@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.