Re: [lm-sensors] [PATCH] support tmp112

[Guenter Roeck <linux@roeck-us.net>]

On 08/06/2013 08:29 AM, Felten, Lothar wrote:
> Hello Guenter,
>
> Sorry for the confusion, I modified the patch now it uses a higher speed.
>
> This patch adds support for the tmp112 temperature sensor which is similar to the lm75 series.
>
> Best regards,
> Lothar
>
> diff --git a/Documentation/hwmon/lm75 b/Documentation/hwmon/lm75
> index 2560a9c..c6a5ff1 100644
> --- a/Documentation/hwmon/lm75
> +++ b/Documentation/hwmon/lm75
> @@ -42,13 +42,14 @@ Supported chips:
>       Addresses scanned: none
>       Datasheet: Publicly available at the ST website
>                  http://www.st.com/internet/analog/product/121769.jsp
> -  * Texas Instruments TMP100, TMP101, TMP105, TMP75, TMP175, TMP275
> -    Prefixes: 'tmp100', 'tmp101', 'tmp105', 'tmp175', 'tmp75', 'tmp275'
> +  * Texas Instruments TMP100, TMP101, TMP105, TMP112, TMP75, TMP175, TMP275
> +    Prefixes: 'tmp100', 'tmp101', 'tmp105', 'tmp112', 'tmp175', 'tmp75', 'tmp275'
>       Addresses scanned: none
>       Datasheet: Publicly available at the Texas Instruments website
>                  http://www.ti.com/product/tmp100
>                  http://www.ti.com/product/tmp101
>                  http://www.ti.com/product/tmp105
> +               http://www.ti.com/product/tmp112
>                  http://www.ti.com/product/tmp75
>                  http://www.ti.com/product/tmp175
>                  http://www.ti.com/product/tmp275
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index e989f7f..4316313 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -652,8 +652,8 @@ config SENSORS_LM75
>                  - NXP's LM75A
>                  - ST Microelectronics STDS75
>                  - TelCom (now Microchip) TCN75
> -               - Texas Instruments TMP100, TMP101, TMP105, TMP75, TMP175,
> -                 TMP275
> +               - Texas Instruments TMP100, TMP101, TMP105, TMP112,
> +                  TMP175, TMP275, TMP75
>
>            This driver supports driver model based binding through board
>            specific I2C device tables.
> diff --git a/drivers/hwmon/lm75.c b/drivers/hwmon/lm75.c
> index c03b490..3fe54ac 100644
> --- a/drivers/hwmon/lm75.c
> +++ b/drivers/hwmon/lm75.c
> @@ -49,6 +49,7 @@ enum lm75_type {              /* keep sorted in alphabetical order */
>          tmp100,
>          tmp101,
>          tmp105,
> +       tmp112,
>          tmp175,
>          tmp275,
>          tmp75,
> @@ -236,6 +237,12 @@ lm75_probe(struct i2c_client *client, const struct i2c_device_id *id)
>                  data->sample_time = HZ;
>                  clr_mask |= 1 << 7;             /* not one-shot mode */
>                  break;
> +       case tmp112:
> +               set_mask |= 3 << 5;             /* 12-bit mode */
> +               clr_mask |= 1 << 7;             /* not one-shot mode */
> +               data->resolution = 12;
> +               data->sample_time = HZ / 4;
> +               break;
>          case tmp105:
>          case tmp175:
>          case tmp275:
> @@ -306,6 +313,7 @@ static const struct i2c_device_id lm75_ids[] = {
>          { "tmp100", tmp100, },
>          { "tmp101", tmp101, },
>          { "tmp105", tmp105, },
> +       { "tmp112", tmp112, },
>          { "tmp175", tmp175, },
>          { "tmp275", tmp275, },
>          { "tmp75", tmp75, },
>
> Signed-off-by: l-felten@ti.com
>

Hi Lothar,

Signed-off is still at the end :)

Also, looks like your mailer replaced all tabs with spaces, or your editor is set to do the same.
checkpatch result is 'total: 5 errors, 8 warnings, 52 lines checked'

Please fix.

Thanks,
Guenter


_______________________________________________
lm-sensors mailing list
lm-sensors@lm-sensors.org
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors