From: gerg@uclinux.org (Greg Ungerer)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 0/8] ARM: imx: add IMX50 SoC support
Date: Fri, 25 Oct 2013 22:53:37 +1000 [thread overview]
Message-ID: <526A69D1.80506@uclinux.org> (raw)
In-Reply-To: <20131024150050.GA14529@S2101-09.ap.freescale.net>
Hi Shawn
On 25/10/13 01:00, Shawn Guo wrote:
> Hi Greg,
>
> On Fri, Oct 18, 2013 at 04:04:12PM +1000, gerg at uclinux.org wrote:
>> From: Greg Ungerer <gerg@uclinux.org>
>>
>> This set of patches is the code and device tree support for the Freescale
>> IMX50 SoC. This part is similar to the IMX53 SoC family, and I have resued
>> as much of its support as possible. These patches are against 3.12-rc5.
>
> Nice patches. Can you please base it on branch below with your next
> posting, so that I can apply them more easily?
>
> git://git.linaro.org/people/shawnguo/linux-2.6.git for-next
Sure thing. I'll roll in all your suggestions, and send out a v2 in
the next few days. Thanks for the review.
Regards
Greg
> Shawn
>
>> With these changes you can load and run on the Freescale IMX50-EVK board.
>>
>> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
>> ---
>> arch/arm/Kconfig.debug | 9
>> arch/arm/boot/dts/Makefile | 1
>> arch/arm/boot/dts/imx50-evk.dts | 89 +++
>> arch/arm/boot/dts/imx50-pinfunc.h | 923 ++++++++++++++++++++++++++++++++++++
>> arch/arm/boot/dts/imx50.dtsi | 659 +++++++++++++++++++++++++
>> arch/arm/include/debug/imx-uart.h | 10
>> arch/arm/mach-imx/Kconfig | 9
>> arch/arm/mach-imx/Makefile | 1
>> arch/arm/mach-imx/clk-imx51-imx53.c | 79 +++
>> arch/arm/mach-imx/common.h | 3
>> arch/arm/mach-imx/mach-imx50.c | 52 ++
>> drivers/pinctrl/Kconfig | 8
>> drivers/pinctrl/Makefile | 1
>> drivers/pinctrl/pinctrl-imx50.c | 426 ++++++++++++++++
>> 14 files changed, 2270 insertions(+)
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
>
prev parent reply other threads:[~2013-10-25 12:53 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-10-18 6:04 [PATCH 0/8] ARM: imx: add IMX50 SoC support gerg at uclinux.org
2013-10-18 6:04 ` [PATCH 1/8] ARM: imx: add debug uart support for IMX50 SoC gerg at uclinux.org
2013-10-18 6:04 ` [PATCH 2/8] ARM: imx: add clocking support code for the " gerg at uclinux.org
2013-10-22 12:27 ` Sascha Hauer
2013-10-23 3:19 ` Greg Ungerer
2013-10-23 9:19 ` Jason Cooper
2013-10-23 12:44 ` Greg Ungerer
2013-10-23 13:42 ` Jason Cooper
2013-10-24 15:11 ` Shawn Guo
2013-10-18 6:04 ` [PATCH 3/8] ARM: imx: add pinctrl " gerg at uclinux.org
2013-10-24 15:16 ` Shawn Guo
2013-10-18 6:04 ` [PATCH 4/8] ARM: imx: add support code for IMX50 based machines gerg at uclinux.org
2013-10-24 11:11 ` Rob Herring
2013-10-28 6:38 ` Greg Ungerer
2013-10-28 19:57 ` Rob Herring
2013-10-18 6:04 ` [PATCH 5/8] ARM: imx: allow configuration of the IMX50 SoC gerg at uclinux.org
2013-10-24 15:17 ` Shawn Guo
2013-10-18 6:04 ` [PATCH 6/8] ARM: dts: imx: add device tree pin definitions for the IMX50 gerg at uclinux.org
2013-10-18 6:04 ` [PATCH 7/8] ARM: dts: imx: add IMX50 SoC device tree bindings gerg at uclinux.org
2013-10-22 12:35 ` Sascha Hauer
2013-10-22 20:08 ` Matt Sealey
2013-10-22 21:57 ` Sascha Hauer
2013-10-22 22:42 ` Benoît Thébaudeau
2013-10-22 23:06 ` Matt Sealey
2013-10-23 0:17 ` Benoît Thébaudeau
2013-10-23 5:55 ` Greg Ungerer
2013-10-24 21:13 ` Matt Sealey
2013-10-23 5:40 ` Greg Ungerer
2013-10-24 15:26 ` Shawn Guo
2013-10-18 6:04 ` [PATCH 8/8] ARM: dts: imx: add device tree support for Freescale imx50evk board gerg at uclinux.org
2013-10-24 15:29 ` Shawn Guo
2013-10-23 9:14 ` [PATCH 0/8] ARM: imx: add IMX50 SoC support Jason Cooper
2013-10-23 12:39 ` Greg Ungerer
2013-10-24 15:00 ` Shawn Guo
2013-10-25 12:53 ` Greg Ungerer [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=526A69D1.80506@uclinux.org \
--to=gerg@uclinux.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.