Re: Error testing 3.10.9-1.0.0-alpha kernel [was Re: Request to integrate freescale i.mx 3.10.9-1.0.0 alpha release into dora branch of meta-fsl-arm]

[Daiane Angolini <daiane.angolini@freescale.com>]

On 10/29/2013 10:13 AM, Daiane Angolini wrote:
> On 10/29/2013 09:29 AM, Gonzalez, Alex wrote:
>> Thanks Otavio.
>>
>> It also does not boot for me on a Sabre platform.
>>
>> Does it boot on any i.MX6 board at all?
>
> Give me time and I will test it.
>
> I'm sorry, I completely forgot about this issue :(

I was not able to load kernel using the default environment, please, see 
log at the end.

Give me sometime that I'm going to debug it....


U-Boot 2013.10 (Oct 29 2013 - 10:59:08)

CPU:   Freescale i.MX6Q rev1.1 at 792 MHz
Reset cause: POR
Board: MX6-SabreSD
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
*** Warning - bad CRC, using default environment

No panel detected: default to HDMI
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0
mmc1 is current device
reading boot.scr
** Unable to read file boot.scr **
reading uImage
5092272 bytes read in 382 ms (12.7 MiB/s)
Booting from mmc ...
reading imx6q-sabresd.dtb
45295 bytes read in 22 ms (2 MiB/s)
## Booting kernel from Legacy Image at 12000000 ...
    Image Name:   Linux-3.10.9-1.0.0_alpha+gdbf364
    Image Type:   ARM Linux Kernel Image (uncompressed)
    Data Size:    5092208 Bytes = 4.9 MiB
    Load Address: 10008000
    Entry Point:  10008000
    Verifying Checksum ... OK
## Flattened Device Tree blob at 11000000
    Booting using the fdt blob at 0x11000000
    Loading Kernel Image ... OK
    Using Device Tree in place at 11000000, end 1100e0ee

Starting kernel ...


>
>
>
>>
>> Thanks,
>> Alex
>>
>> -----Original Message-----
>> From: otavio.salvador@gmail.com [mailto:otavio.salvador@gmail.com] On
>> Behalf Of Otavio Salvador
>> Sent: martes, 29 de octubre de 2013 12:08
>> To: Gonzalez, Alex
>> Cc: meta-freescale@yoctoproject.org; Post Lauren-RAA013
>> Subject: Re: [meta-freescale] Error testing 3.10.9-1.0.0-alpha kernel
>> [was Re: Request to integrate freescale i.mx 3.10.9-1.0.0 alpha
>> release into dora branch of meta-fsl-arm]
>>
>> On Tue, Oct 29, 2013 at 8:49 AM, Gonzalez, Alex
>> <Alex.Gonzalez@digi.com> wrote:
>>> Sorry to ask again, did anyone manage to boot an i.MX6 Sabre board
>>> with the 3.10 kernel default configuration and device tree?
>>>
>>> I am assuming no answer means no, but just in case.
>>
>> I can't, my SabreSD board is bad (too unstable due hardware issues)
>> and I cannot use for testing.
>>
>
>


-- 
Daiane