From: Anand <anandkumar_santhanam@pmc-sierra.com>
To: linux-scsi@vger.kernel.org
Cc: xjtuwjp@gmail.com, Sangeetha.Gnanasekaran@pmcs.com,
Viswas.G@pmcs.com, Nikith.Ganigarakoppal@pmcs.com
Subject: [PATCH V2 3/4] pm80xx: Resetting the phy state.
Date: Wed, 13 Nov 2013 05:33:37 -0800 [thread overview]
Message-ID: <52837FB1.1030801@pmc-sierra.com> (raw)
>From e2c21b550d03909dd19e6559481d871ad1e28344 Mon Sep 17 00:00:00 2001
From: Nikith Ganigarakoppal <Nikith.Ganigarakoppal@pmcs.com>
Date: Wed, 30 Oct 2013 16:23:47 +0530
Subject: [PATCH V2 3/4] pm80xx: Resetting the phy state.
Setting the phy state for hard reset response.
After sending hard reset for a device ,phy down event sets
the phy state to zero but for phy up event it will not set
the phy state again.This will cause problem to successive
hard resets.
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
---
drivers/scsi/pm8001/pm8001_hwi.c | 2 ++
drivers/scsi/pm8001/pm8001_hwi.h | 4 ++++
drivers/scsi/pm8001/pm80xx_hwi.c | 2 ++
drivers/scsi/pm8001/pm80xx_hwi.h | 2 ++
4 files changed, 10 insertions(+), 0 deletions(-)
diff --git a/drivers/scsi/pm8001/pm8001_hwi.c b/drivers/scsi/pm8001/pm8001_hwi.c
index 9961616..b23f49d 100644
--- a/drivers/scsi/pm8001/pm8001_hwi.c
+++ b/drivers/scsi/pm8001/pm8001_hwi.c
@@ -3403,6 +3403,7 @@ hw_event_sas_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
unsigned long flags;
u8 deviceType = pPayload->sas_identify.dev_type;
port->port_state = portstate;
+ phy->phy_state = PHY_STATE_LINK_UP_SPC;
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_SAS_PHY_UP port id = %d, phy id = %d\n",
port_id, phy_id));
@@ -3483,6 +3484,7 @@ hw_event_sata_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
pm8001_printk("HW_EVENT_SATA_PHY_UP port id = %d,"
" phy id = %d\n", port_id, phy_id));
port->port_state = portstate;
+ phy->phy_state = PHY_STATE_LINK_UP_SPC;
port->port_attached = 1;
pm8001_get_lrate_mode(phy, link_rate);
phy->phy_type |= PORT_TYPE_SATA;
diff --git a/drivers/scsi/pm8001/pm8001_hwi.h b/drivers/scsi/pm8001/pm8001_hwi.h
index 6d91e24..e4867e6 100644
--- a/drivers/scsi/pm8001/pm8001_hwi.h
+++ b/drivers/scsi/pm8001/pm8001_hwi.h
@@ -131,6 +131,10 @@
#define LINKRATE_30 (0x02 << 8)
#define LINKRATE_60 (0x04 << 8)
+/* for phy state */
+
+#define PHY_STATE_LINK_UP_SPC 0x1
+
/* for new SPC controllers MEMBASE III is shared between BIOS and DATA */
#define GSM_SM_BASE 0x4F0000
struct mpi_msg_hdr{
diff --git a/drivers/scsi/pm8001/pm80xx_hwi.c b/drivers/scsi/pm8001/pm80xx_hwi.c
index 4ebc79b..41bee62 100644
--- a/drivers/scsi/pm8001/pm80xx_hwi.c
+++ b/drivers/scsi/pm8001/pm80xx_hwi.c
@@ -2894,6 +2894,7 @@ hw_event_sas_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
unsigned long flags;
u8 deviceType = pPayload->sas_identify.dev_type;
port->port_state = portstate;
+ phy->phy_state = PHY_STATE_LINK_UP_SPCV;
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"portid:%d; phyid:%d; linkrate:%d; "
"portstate:%x; devicetype:%x\n",
@@ -2978,6 +2979,7 @@ hw_event_sata_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
port_id, phy_id, link_rate, portstate));
port->port_state = portstate;
+ phy->phy_state = PHY_STATE_LINK_UP_SPCV;
port->port_attached = 1;
pm8001_get_lrate_mode(phy, link_rate);
phy->phy_type |= PORT_TYPE_SATA;
diff --git a/drivers/scsi/pm8001/pm80xx_hwi.h b/drivers/scsi/pm8001/pm80xx_hwi.h
index c86816b..9970a38 100644
--- a/drivers/scsi/pm8001/pm80xx_hwi.h
+++ b/drivers/scsi/pm8001/pm80xx_hwi.h
@@ -215,6 +215,8 @@
#define SAS_DOPNRJT_RTRY_TMO 128
#define SAS_COPNRJT_RTRY_TMO 128
+/* for phy state */
+#define PHY_STATE_LINK_UP_SPCV 0x2
/*
Making ORR bigger than IT NEXUS LOSS which is 2000000us = 2 second.
Assuming a bigger value 3 second, 3000000/128 = 23437.5 where 128
--
1.7.1
reply other threads:[~2013-11-13 13:30 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=52837FB1.1030801@pmc-sierra.com \
--to=anandkumar_santhanam@pmc-sierra.com \
--cc=Nikith.Ganigarakoppal@pmcs.com \
--cc=Sangeetha.Gnanasekaran@pmcs.com \
--cc=Viswas.G@pmcs.com \
--cc=linux-scsi@vger.kernel.org \
--cc=xjtuwjp@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.