All of lore.kernel.org
 help / color / mirror / Atom feed
From: Josh Wu <josh.wu@atmel.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 2/2] ARM: at91: sama5d3: mmc: save enviroment as a fat file (uboot.env)
Date: Wed, 27 Nov 2013 18:26:38 +0800	[thread overview]
Message-ID: <5295C8DE.3020409@atmel.com> (raw)
In-Reply-To: <528F2D1E.20800@atmel.com>

On 11/22/2013 6:08 PM, Bo Shen wrote:
> Hi Josh,
>
> On 11/22/2013 02:58 PM, Josh Wu wrote:
>> This patch will save U-Boot environment as a file: uboot.env, in FAT 
>> partition
>> instead of saving it in raw sector of SD card.
>>
>> Since saving environment in raw sector has risk of corrupting the SD 
>> card and
>> only can use very small size. Save as a FAT file has no above 
>> limitation.
>>
>> Signed-off-by: Josh Wu <josh.wu@atmel.com>
>> ---
>>   include/configs/sama5d3xek.h |   10 +++++++---
>>   1 file changed, 7 insertions(+), 3 deletions(-)
>
> Tested on sama5d31ek board. It doesn't work. Please check it, and also 
> check on at91sam9x5ek board.
>
> Please take the following information as a reference.
> --->8---
> U-Boot 2013.10-00389-gf37e980 (Nov 22 2013 - 17:56:53)
>
> CPU: SAMA5D31
> Crystal frequency:       12 MHz
> CPU clock        :      528 MHz
> Master clock     :      132 MHz
> DRAM:  512 MiB
> NAND:  256 MiB
> MMC:   mci: 0
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 22000000 Hz, block size 512
> reading uboot.env
>
> ** Unable to read "uboot.env" from mmc0:1 **
> Using default environment
>
> In:    serial
> Out:   serial
> Err:   serial
> Net:   macb0
> Warning: failed to set MAC address
> , usb_ether
> Hit any key to stop autoboot:  0
> U-Boot> fat
>   fatinfo fatload fatls fatwrite
> U-Boot> fatls mmc 0
>     20737   boot.bin
>    332916   u-boot.bin
>
> 2 file(s), 0 dir(s)
>
> U-Boot> saveenv
> Saving Environment to FAT...
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 22000000 Hz, block size 512
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 22000000 Hz, block size 512
> writing uboot.env
> done
> U-Boot> fatls mmc 0
>     20737   boot.bin
>    332916   u-boot.bin
>
> 2 file(s), 0 dir(s)
> ---8<---

Oops, this indeed happened in my side too. I will follow on this issue. 
Thanks for the testing.

>
>> diff --git a/include/configs/sama5d3xek.h b/include/configs/sama5d3xek.h
>> index 5a6f0fc..a77ab5f 100644
>> --- a/include/configs/sama5d3xek.h
>> +++ b/include/configs/sama5d3xek.h
>> @@ -196,9 +196,13 @@
>>                   "bootm 0x22000000 - 0x21000000"
>>   #elif CONFIG_SYS_USE_MMC
>>   /* bootstrap + u-boot + env in sd card */
>> -#define CONFIG_ENV_IS_IN_MMC
>> -#define CONFIG_ENV_OFFSET    0x2000
>> -#define CONFIG_ENV_SIZE        0x1000
>> +#define CONFIG_ENV_IS_IN_FAT
>> +#define CONFIG_FAT_WRITE
>> +#define FAT_ENV_INTERFACE    "mmc"
>> +#define FAT_ENV_FILE        "uboot.env"
>> +#define FAT_ENV_DEVICE        0
>> +#define FAT_ENV_PART        1
>> +#define CONFIG_ENV_SIZE        0x4000
>>   #define CONFIG_BOOTCOMMAND    "fatload mmc 0:1 0x21000000 dtb; " \
>>                   "fatload mmc 0:1 0x22000000 uImage; " \
>>                   "bootm 0x22000000 - 0x21000000"
>>
>
> Best Regards,
> Bo Shen

Best Regards,
Josh Wu

      reply	other threads:[~2013-11-27 10:26 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-11-22  6:58 [U-Boot] [PATCH 1/2] ARM: at91: at91sam9x5: mmc: save environment as a FAT file (uboot.env) Josh Wu
2013-11-22  6:58 ` [U-Boot] [PATCH 2/2] ARM: at91: sama5d3: mmc: save enviroment as a fat " Josh Wu
2013-11-22 10:08   ` Bo Shen
2013-11-27 10:26     ` Josh Wu [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=5295C8DE.3020409@atmel.com \
    --to=josh.wu@atmel.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.