From: Stefano Babic <sbabic@denx.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PULL-Update] : Please pull u-boot-imx
Date: Fri, 03 Jan 2014 15:51:14 +0100 [thread overview]
Message-ID: <52C6CE62.6050907@denx.de> (raw)
In-Reply-To: <52C592F9.5000604@denx.de>
On 02/01/2014 17:25, Stefano Babic wrote:
> Hi Albert,
>
> my first pull-request in 2014 ! Please pull from u-boot-imx, thanks !
>
Albert, I forget to merge some further patches. This is my updated PULL
request:
The following changes since commit 56eb3da43fab5990a4b7bc118b76c7cae2ceb140:
arm, am335x: update for the siemens boards (2013-11-12 09:53:59 -0500)
are available in the git repository at:
git://www.denx.de/git/u-boot-imx.git master
for you to fetch changes up to 4611d5bab26f93471b84f6f33967cef69b3f723a:
arm: mx5: Add fuse supply enable in fsl_iim (2014-01-03 15:44:06 +0100)
----------------------------------------------------------------
Eric Nelson (8):
i.MX6DQ/DLS: replace pad names with their Linux kernel equivalents
i.MX6DQ/DLS: remove useless mux/pad declarations
i.MX6DQ: Add Pinmux settings that are present in mainline and
Dual-Lite/Solo
i.MX6DQ/DLS: remove unused pad declarations
i.MX6DQ/DLS: whitespace: Align IOMUX_PAD column in declarations
imx-common: remove extraneous semicolon from macro
i.MX6 (DQ/DLS): use macros for mux and pad declarations
ARM: mx6: Update non-Freescale boards to include CPU errata.
Fabio Estevam (24):
configs: imx: Make CONFIG_SYS_PROMPT uniform across FSL boards
wandboard: Return the error immediately when ipuv3_fb_init() fails
wandboard: Return the error when cpu_eth_init() fails
titanium: Return the error when cpu_eth_init() fails
nitrogen6x: Remove unused OCOTP options
mx51evk: Fix pmic_init() argument
mx31pdk: Fix pmic_init() argument
efikamx: Fix pmic_init() argument
power: power_fsl: Pass p->bus in the same way for SPI and I2C cases
mx6sabresd: Fix wrong colors in LVDS splash
mx6sabresd: Add SPI NOR support
imx: Explicitly pass the I2C bus number in pmic_init()
configs: imx: Remove CONFIG_SYS_SPD_BUS_NUM option
mx6: clock: Fix the calculation of PLL_ENET frequency
mx6sabresd: Allow probing HSYNC, VSYNC and DISP_CLK signals
mx6sabresd: Fix LVDS width and color format
doc: README.fuse: Add an example on how to use the fuse API on mx6q
mx6sabre_common.h: Add CONFIG_CMD_FUSE support
mx6: soc: Staticize set_vddsoc()
mx6: soc: Clear the LDO ramp values up prior to setting the LDO
voltages
mx6: soc: Set the VDDSOC at 1.175 V
mx6: soc: Introduce set_ldo_voltage()
mx6: soc: Add the required LDO ramp up delay
mx6: soc: Disable VDDPU regulator
Frank Li (1):
imx6: fix random hang when download by usb
Giuseppe Pagano (5):
udoo: Move and optimize platform register setting.
udoo: Add ethernet support (FEC + Micrel KSZ9031).
udoo: Fix watchdog during kernel boot.
nitrogen6x: Move setup_sata to common part
udoo: Add SATA support on uDoo Board.
Liu Ying (1):
MX6 SabreSD: Use readl() to read the CCM_CCGR3 register
Marek Vasut (3):
Net: FEC: Fix huge memory leak
ARM: mx53: video: Add IPUv3 LCD support for M53EVK
ARM: mxs: tools: Fix errno handling in strtoul() invocation
Michael Heimpold (1):
mxs_gpio: fix the handling in gpio_direction_output()
Otavio Salvador (6):
imx: Easy enabling of SION per-pin using MUX_MODE_SION helper macro
mx28evk: Use 512k for fdt partition to align it
mx28evk: Add 'nandboot' environment command
mx28evk: Extend environment to easy write of NAND system
ARM: mx6: Change the FDT loading address to avoid overlaping
ARM: mx6: Allow enablement of FEC Anatop based clock for all MX6
Sergey Alyoshin (1):
arm: mx5: Add fuse supply enable in fsl_iim
Stefan Roese (1):
mx6: titanium: Move BSP code to barco board directory
Stefano Babic (1):
MX6: fix sata compilation for i.MX6
arch/arm/cpu/armv7/mx5/clock.c | 12 +
arch/arm/cpu/armv7/mx6/clock.c | 23 +-
arch/arm/cpu/armv7/mx6/soc.c | 110 +-
arch/arm/imx-common/Makefile | 3 +
arch/arm/imx-common/cpu.c | 4 +-
arch/arm/imx-common/sata.c | 34 +
arch/arm/include/asm/arch-mx5/clock.h | 1 +
arch/arm/include/asm/arch-mx5/crm_regs.h | 3 +
arch/arm/include/asm/arch-mx6/crm_regs.h | 1 +
arch/arm/include/asm/arch-mx6/imx-regs.h | 23 +
arch/arm/include/asm/arch-mx6/mx6-pins.h | 33 +-
arch/arm/include/asm/arch-mx6/mx6dl_pins.h | 2728
+++++++++-------------
arch/arm/include/asm/arch-mx6/mx6q_pins.h | 2642
++++++++-------------
arch/arm/include/asm/arch-mx6/sys_proto.h | 2 -
arch/arm/include/asm/imx-common/iomux-v3.h | 2 +
arch/arm/include/asm/imx-common/sata.h | 16 +
board/{freescale => barco}/titanium/Makefile | 0
board/{freescale => barco}/titanium/imximage.cfg | 0
board/{freescale => barco}/titanium/titanium.c | 110 +-
board/boundary/nitrogen6x/nitrogen6x.c | 197 +-
board/congatec/cgtqmx6eval/cgtqmx6eval.c | 40 +-
board/denx/m53evk/m53evk.c | 73 +
board/freescale/mx25pdk/mx25pdk.c | 2 +-
board/freescale/mx31pdk/mx31pdk.c | 2 +-
board/freescale/mx35pdk/mx35pdk.c | 2 +-
board/freescale/mx51evk/mx51evk.c | 2 +-
board/freescale/mx53evk/mx53evk.c | 2 +-
board/freescale/mx53loco/mx53loco.c | 2 +-
board/freescale/mx6qarm2/mx6qarm2.c | 68 +-
board/freescale/mx6qsabreauto/mx6qsabreauto.c | 62 +-
board/freescale/mx6sabresd/mx6sabresd.c | 155 +-
board/genesi/mx51_efikamx/efikamx.c | 2 +-
board/udoo/1066mhz_4x256mx16.cfg | 55 +
board/udoo/clocks.cfg | 32 +
board/udoo/ddr-setup.cfg | 87 +
board/udoo/udoo.c | 165 +-
board/udoo/udoo.cfg | 29 +
board/wandboard/wandboard.c | 60 +-
boards.cfg | 4 +-
doc/README.imx6 | 76 +
drivers/gpio/mxs_gpio.c | 4 +-
drivers/misc/fsl_iim.c | 13 +-
drivers/net/fec_mxc.c | 177 +-
drivers/power/power_fsl.c | 3 +-
include/configs/cgtqmx6eval.h | 2 +-
include/configs/imx31_phycore.h | 1 -
include/configs/m53evk.h | 16 +
include/configs/mx25pdk.h | 2 -
include/configs/mx28evk.h | 56 +-
include/configs/mx31pdk.h | 1 -
include/configs/mx35pdk.h | 2 -
include/configs/mx51evk.h | 1 -
include/configs/mx53ard.h | 1 -
include/configs/mx53evk.h | 2 -
include/configs/mx53loco.h | 2 -
include/configs/mx53smd.h | 2 -
include/configs/mx6_common.h | 1 +
include/configs/mx6qarm2.h | 1 -
include/configs/mx6sabre_common.h | 20 +-
include/configs/nitrogen6x.h | 13 +-
include/configs/titanium.h | 1 +
include/configs/udoo.h | 31 +-
include/configs/wandboard.h | 3 +-
include/micrel.h | 5 +
tools/mxsimage.c | 1 +
65 files changed, 3444 insertions(+), 3781 deletions(-)
create mode 100644 arch/arm/imx-common/sata.c
create mode 100644 arch/arm/include/asm/imx-common/sata.h
rename board/{freescale => barco}/titanium/Makefile (100%)
rename board/{freescale => barco}/titanium/imximage.cfg (100%)
rename board/{freescale => barco}/titanium/titanium.c (66%)
create mode 100644 board/udoo/1066mhz_4x256mx16.cfg
create mode 100644 board/udoo/clocks.cfg
create mode 100644 board/udoo/ddr-setup.cfg
create mode 100644 board/udoo/udoo.cfg
Thanks,
Stefano
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
next prev parent reply other threads:[~2014-01-03 14:51 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-01-02 16:25 [U-Boot] [PULL] : Please pull u-boot-imx Stefano Babic
2014-01-03 14:51 ` Stefano Babic [this message]
2014-01-06 8:31 ` [U-Boot] [PULL-Update] " Albert ARIBAUD
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=52C6CE62.6050907@denx.de \
--to=sbabic@denx.de \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.