Renesas RCar device-tree USB series

Renesas RCar device-tree USB series

[Ben Dooks]

This is a new series covering enabling the RCar series of SoCs USB
with device-tree based booting. It has been tested on the R8A7790
Lager board.

Improvements from the previous series include:
	
	- mapping usb to the relevant phy by dt
	- better use of existing pci of functions

Note, there is still an issue with the second gigabyte of memory on
the Lager, which with current kernels causes the system to abort on
startup. This series will only work if the top memory area is disabled.

[PATCH 1/9] pci-rcar-gen2: add devicetree support

[Ben Dooks]

Add OF match table for pci-rcar-gen2 driver for device tree support.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
---
Updates since v1:
	- moved documentation into patch
	- moved to using bus-range parsing
	- ensured usb phy can be linked to usb devices

Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: linux-pci@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: devicetree@vger.kernel.org
---
 .../bindings/pci/renessas,pci-rcar-gen2.txt        | 52 ++++++++++++++++++++++
 drivers/pci/host/pci-rcar-gen2.c                   | 33 +++++++++++++-
 2 files changed, 83 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt

diff --git a/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
new file mode 100644
index 0000000..bd6d291
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
@@ -0,0 +1,52 @@
+Renesas AHB to PCI bridge
+-------------------------
+
+This is the bridge used internally to connect the USB controllers to the
+AHB. There is one bridge instance per USB port consiting of an internal
+OHCI and EHCI controller.
+
+Required properties:
+ - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC
+ - reg : A list of physical regions to access the device. The first is
+         the operational registers for the OHCI/EHCI controller and the
+	 second region is for the bridge configuration and control registers.
+ - interrupts : interrupt for the device
+ - clocks : The reference to the device clock
+ - bus-range: The PCI bus number ranges. As this is a single bus, the range
+		should be specified as the same value twice.
+
+
+Example SoC configuration:
+
+	pci0: pci@ee090000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee090000 0x0 0xc00>,
+		      <0x0 0xee080000 0x0 0x1100>;
+		interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+
+		bus-range = <0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+	};
+
+Example board setup:
+
+&pci1 {
+	status = "okay";
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+
+	pci@0,1 {
+		reg = <0x800 0 0 0 0>;
+		device_type = "pci";
+		usb-phy = <&usbphy>;
+	};
+
+	pci@0,2 {
+		reg = <0x1000 0 0 0 0>;
+		device_type = "pci";
+		usb-phy = <&usbphy>;
+	};
+};
diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
index fd3e3ab..1216784 100644
--- a/drivers/pci/host/pci-rcar-gen2.c
+++ b/drivers/pci/host/pci-rcar-gen2.c
@@ -16,6 +16,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/pci.h>
+#include <linux/of_pci.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/sizes.h>
@@ -98,6 +99,7 @@ struct rcar_pci_priv {
 	struct resource io_res;
 	struct resource mem_res;
 	struct resource *cfg_res;
+	unsigned busnr;
 	int irq;
 	unsigned long window_size;
 };
@@ -312,8 +314,8 @@ static int rcar_pci_setup(int nr, struct pci_sys_data *sys)
 	pci_add_resource(&sys->resources, &priv->io_res);
 	pci_add_resource(&sys->resources, &priv->mem_res);
 
-	/* Setup bus number based on platform device id */
-	sys->busnr = to_platform_device(priv->dev)->id;
+	/* Setup bus number based on platform device id / of bus-range */
+	sys->busnr = priv->busnr;
 	return 1;
 }
 
@@ -366,6 +368,23 @@ static int rcar_pci_probe(struct platform_device *pdev)
 
 	priv->window_size = SZ_1G;
 
+	if (pdev->dev.of_node) {
+		struct resource busnr;
+		int ret;
+
+		ret = of_pci_parse_bus_range(pdev->dev.of_node, &busnr);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "failed to parse bus-range\n");
+			return ret;
+		}
+		
+		priv->busnr = busnr.start;
+		if (busnr.end != busnr.start)
+			dev_warn(&pdev->dev, "only one bus number supported\n");
+	} else {
+		priv->busnr = pdev->id;
+	}
+
 	hw_private[0] = priv;
 	memset(&hw, 0, sizeof(hw));
 	hw.nr_controllers = ARRAY_SIZE(hw_private);
@@ -377,11 +396,21 @@ static int rcar_pci_probe(struct platform_device *pdev)
 	return 0;
 }
 
+#ifdef CONFIG_OF
+static struct of_device_id rcar_pci_of_match[] = {
+	{ .compatible = "renesas,pci-r8a7790", },
+	{ },
+};
+
+MODULE_DEVICE_TABLE(of, rcar_pci_of_match);
+#endif
+
 static struct platform_driver rcar_pci_driver = {
 	.driver = {
 		.name = "pci-rcar-gen2",
 		.owner = THIS_MODULE,
 		.suppress_bind_attrs = true,
+		.of_match_table = of_match_ptr(rcar_pci_of_match),
 	},
 	.probe = rcar_pci_probe,
 };
-- 
1.9.0

[PATCH 1/9] pci-rcar-gen2: add devicetree support

[Ben Dooks]

Add OF match table for pci-rcar-gen2 driver for device tree support.

Signed-off-by: Ben Dooks <ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>
---
Updates since v1:
	- moved documentation into patch
	- moved to using bus-range parsing
	- ensured usb phy can be linked to usb devices

Cc: Bjorn Helgaas <bhelgaas-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org>
Cc: Simon Horman <horms-/R6kz+dDXgpPR4JQBCEnsQ@public.gmane.org>
Cc: linux-pci-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: linux-sh-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
---
 .../bindings/pci/renessas,pci-rcar-gen2.txt        | 52 ++++++++++++++++++++++
 drivers/pci/host/pci-rcar-gen2.c                   | 33 +++++++++++++-
 2 files changed, 83 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt

diff --git a/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
new file mode 100644
index 0000000..bd6d291
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
@@ -0,0 +1,52 @@
+Renesas AHB to PCI bridge
+-------------------------
+
+This is the bridge used internally to connect the USB controllers to the
+AHB. There is one bridge instance per USB port consiting of an internal
+OHCI and EHCI controller.
+
+Required properties:
+ - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC
+ - reg : A list of physical regions to access the device. The first is
+         the operational registers for the OHCI/EHCI controller and the
+	 second region is for the bridge configuration and control registers.
+ - interrupts : interrupt for the device
+ - clocks : The reference to the device clock
+ - bus-range: The PCI bus number ranges. As this is a single bus, the range
+		should be specified as the same value twice.
+
+
+Example SoC configuration:
+
+	pci0: pci@ee090000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee090000 0x0 0xc00>,
+		      <0x0 0xee080000 0x0 0x1100>;
+		interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+
+		bus-range = <0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+	};
+
+Example board setup:
+
+&pci1 {
+	status = "okay";
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+
+	pci@0,1 {
+		reg = <0x800 0 0 0 0>;
+		device_type = "pci";
+		usb-phy = <&usbphy>;
+	};
+
+	pci@0,2 {
+		reg = <0x1000 0 0 0 0>;
+		device_type = "pci";
+		usb-phy = <&usbphy>;
+	};
+};
diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
index fd3e3ab..1216784 100644
--- a/drivers/pci/host/pci-rcar-gen2.c
+++ b/drivers/pci/host/pci-rcar-gen2.c
@@ -16,6 +16,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/pci.h>
+#include <linux/of_pci.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/sizes.h>
@@ -98,6 +99,7 @@ struct rcar_pci_priv {
 	struct resource io_res;
 	struct resource mem_res;
 	struct resource *cfg_res;
+	unsigned busnr;
 	int irq;
 	unsigned long window_size;
 };
@@ -312,8 +314,8 @@ static int rcar_pci_setup(int nr, struct pci_sys_data *sys)
 	pci_add_resource(&sys->resources, &priv->io_res);
 	pci_add_resource(&sys->resources, &priv->mem_res);
 
-	/* Setup bus number based on platform device id */
-	sys->busnr = to_platform_device(priv->dev)->id;
+	/* Setup bus number based on platform device id / of bus-range */
+	sys->busnr = priv->busnr;
 	return 1;
 }
 
@@ -366,6 +368,23 @@ static int rcar_pci_probe(struct platform_device *pdev)
 
 	priv->window_size = SZ_1G;
 
+	if (pdev->dev.of_node) {
+		struct resource busnr;
+		int ret;
+
+		ret = of_pci_parse_bus_range(pdev->dev.of_node, &busnr);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "failed to parse bus-range\n");
+			return ret;
+		}
+		
+		priv->busnr = busnr.start;
+		if (busnr.end != busnr.start)
+			dev_warn(&pdev->dev, "only one bus number supported\n");
+	} else {
+		priv->busnr = pdev->id;
+	}
+
 	hw_private[0] = priv;
 	memset(&hw, 0, sizeof(hw));
 	hw.nr_controllers = ARRAY_SIZE(hw_private);
@@ -377,11 +396,21 @@ static int rcar_pci_probe(struct platform_device *pdev)
 	return 0;
 }
 
+#ifdef CONFIG_OF
+static struct of_device_id rcar_pci_of_match[] = {
+	{ .compatible = "renesas,pci-r8a7790", },
+	{ },
+};
+
+MODULE_DEVICE_TABLE(of, rcar_pci_of_match);
+#endif
+
 static struct platform_driver rcar_pci_driver = {
 	.driver = {
 		.name = "pci-rcar-gen2",
 		.owner = THIS_MODULE,
 		.suppress_bind_attrs = true,
+		.of_match_table = of_match_ptr(rcar_pci_of_match),
 	},
 	.probe = rcar_pci_probe,
 };
-- 
1.9.0

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/9] pci-rcar-gen2: add devicetree support

[Ben Dooks]

Add OF match table for pci-rcar-gen2 driver for device tree support.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
---
Updates since v1:
	- moved documentation into patch
	- moved to using bus-range parsing
	- ensured usb phy can be linked to usb devices

Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: linux-pci@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: devicetree@vger.kernel.org
---
 .../bindings/pci/renessas,pci-rcar-gen2.txt        | 52 ++++++++++++++++++++++
 drivers/pci/host/pci-rcar-gen2.c                   | 33 +++++++++++++-
 2 files changed, 83 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt

diff --git a/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
new file mode 100644
index 0000000..bd6d291
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
@@ -0,0 +1,52 @@
+Renesas AHB to PCI bridge
+-------------------------
+
+This is the bridge used internally to connect the USB controllers to the
+AHB. There is one bridge instance per USB port consiting of an internal
+OHCI and EHCI controller.
+
+Required properties:
+ - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC
+ - reg : A list of physical regions to access the device. The first is
+         the operational registers for the OHCI/EHCI controller and the
+	 second region is for the bridge configuration and control registers.
+ - interrupts : interrupt for the device
+ - clocks : The reference to the device clock
+ - bus-range: The PCI bus number ranges. As this is a single bus, the range
+		should be specified as the same value twice.
+
+
+Example SoC configuration:
+
+	pci0: pci@ee090000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee090000 0x0 0xc00>,
+		      <0x0 0xee080000 0x0 0x1100>;
+		interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+
+		bus-range = <0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+	};
+
+Example board setup:
+
+&pci1 {
+	status = "okay";
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+
+	pci@0,1 {
+		reg = <0x800 0 0 0 0>;
+		device_type = "pci";
+		usb-phy = <&usbphy>;
+	};
+
+	pci@0,2 {
+		reg = <0x1000 0 0 0 0>;
+		device_type = "pci";
+		usb-phy = <&usbphy>;
+	};
+};
diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
index fd3e3ab..1216784 100644
--- a/drivers/pci/host/pci-rcar-gen2.c
+++ b/drivers/pci/host/pci-rcar-gen2.c
@@ -16,6 +16,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/pci.h>
+#include <linux/of_pci.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/sizes.h>
@@ -98,6 +99,7 @@ struct rcar_pci_priv {
 	struct resource io_res;
 	struct resource mem_res;
 	struct resource *cfg_res;
+	unsigned busnr;
 	int irq;
 	unsigned long window_size;
 };
@@ -312,8 +314,8 @@ static int rcar_pci_setup(int nr, struct pci_sys_data *sys)
 	pci_add_resource(&sys->resources, &priv->io_res);
 	pci_add_resource(&sys->resources, &priv->mem_res);
 
-	/* Setup bus number based on platform device id */
-	sys->busnr = to_platform_device(priv->dev)->id;
+	/* Setup bus number based on platform device id / of bus-range */
+	sys->busnr = priv->busnr;
 	return 1;
 }
 
@@ -366,6 +368,23 @@ static int rcar_pci_probe(struct platform_device *pdev)
 
 	priv->window_size = SZ_1G;
 
+	if (pdev->dev.of_node) {
+		struct resource busnr;
+		int ret;
+
+		ret = of_pci_parse_bus_range(pdev->dev.of_node, &busnr);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "failed to parse bus-range\n");
+			return ret;
+		}
+		
+		priv->busnr = busnr.start;
+		if (busnr.end != busnr.start)
+			dev_warn(&pdev->dev, "only one bus number supported\n");
+	} else {
+		priv->busnr = pdev->id;
+	}
+
 	hw_private[0] = priv;
 	memset(&hw, 0, sizeof(hw));
 	hw.nr_controllers = ARRAY_SIZE(hw_private);
@@ -377,11 +396,21 @@ static int rcar_pci_probe(struct platform_device *pdev)
 	return 0;
 }
 
+#ifdef CONFIG_OF
+static struct of_device_id rcar_pci_of_match[] = {
+	{ .compatible = "renesas,pci-r8a7790", },
+	{ },
+};
+
+MODULE_DEVICE_TABLE(of, rcar_pci_of_match);
+#endif
+
 static struct platform_driver rcar_pci_driver = {
 	.driver = {
 		.name = "pci-rcar-gen2",
 		.owner = THIS_MODULE,
 		.suppress_bind_attrs = true,
+		.of_match_table = of_match_ptr(rcar_pci_of_match),
 	},
 	.probe = rcar_pci_probe,
 };
-- 
1.9.0

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Ben Dooks]

On 06/03/14 18:01, Ben Dooks wrote:
> Add OF match table for pci-rcar-gen2 driver for device tree support.
>

> diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
> index fd3e3ab..1216784 100644
> --- a/drivers/pci/host/pci-rcar-gen2.c
> +++ b/drivers/pci/host/pci-rcar-gen2.c
> @@ -16,6 +16,7 @@
>   #include <linux/kernel.h>
>   #include <linux/module.h>
>   #include <linux/pci.h>
> +#include <linux/of_pci.h>
>   #include <linux/platform_device.h>
>   #include <linux/pm_runtime.h>
>   #include <linux/sizes.h>

Apologies all, there's a missing include of <linux/of.h> which should
have been added here


-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Sergei Shtylyov]

Hello.

On 03/06/2014 09:21 PM, Ben Dooks wrote:

>> Add OF match table for pci-rcar-gen2 driver for device tree support.
[...]

>> diff --git a/drivers/pci/host/pci-rcar-gen2.c
>> b/drivers/pci/host/pci-rcar-gen2.c
>> index fd3e3ab..1216784 100644
>> --- a/drivers/pci/host/pci-rcar-gen2.c
>> +++ b/drivers/pci/host/pci-rcar-gen2.c
>> @@ -16,6 +16,7 @@
>>   #include <linux/kernel.h>
>>   #include <linux/module.h>
>>   #include <linux/pci.h>
>> +#include <linux/of_pci.h>
>>   #include <linux/platform_device.h>
>>   #include <linux/pm_runtime.h>
>>   #include <linux/sizes.h>

> Apologies all, there's a missing include of <linux/of.h> which should
> have been added here

    Have you ever re-posted this patch fixed? If not, it's not going to be 
merged for 3.15 I guess...

WBR, Sergei

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Sergei Shtylyov]

Hello.

On 03/06/2014 09:21 PM, Ben Dooks wrote:

>> Add OF match table for pci-rcar-gen2 driver for device tree support.
[...]

>> diff --git a/drivers/pci/host/pci-rcar-gen2.c
>> b/drivers/pci/host/pci-rcar-gen2.c
>> index fd3e3ab..1216784 100644
>> --- a/drivers/pci/host/pci-rcar-gen2.c
>> +++ b/drivers/pci/host/pci-rcar-gen2.c
>> @@ -16,6 +16,7 @@
>>   #include <linux/kernel.h>
>>   #include <linux/module.h>
>>   #include <linux/pci.h>
>> +#include <linux/of_pci.h>
>>   #include <linux/platform_device.h>
>>   #include <linux/pm_runtime.h>
>>   #include <linux/sizes.h>

> Apologies all, there's a missing include of <linux/of.h> which should
> have been added here

    Have you ever re-posted this patch fixed? If not, it's not going to be 
merged for 3.15 I guess...

WBR, Sergei

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Sergei Shtylyov]

Hello.

On 03/06/2014 09:21 PM, Ben Dooks wrote:

>> Add OF match table for pci-rcar-gen2 driver for device tree support.
[...]

>> diff --git a/drivers/pci/host/pci-rcar-gen2.c
>> b/drivers/pci/host/pci-rcar-gen2.c
>> index fd3e3ab..1216784 100644
>> --- a/drivers/pci/host/pci-rcar-gen2.c
>> +++ b/drivers/pci/host/pci-rcar-gen2.c
>> @@ -16,6 +16,7 @@
>>   #include <linux/kernel.h>
>>   #include <linux/module.h>
>>   #include <linux/pci.h>
>> +#include <linux/of_pci.h>
>>   #include <linux/platform_device.h>
>>   #include <linux/pm_runtime.h>
>>   #include <linux/sizes.h>

> Apologies all, there's a missing include of <linux/of.h> which should
> have been added here

    Have you ever re-posted this patch fixed? If not, it's not going to be 
merged for 3.15 I guess...

WBR, Sergei

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Ben Dooks]

On 30/03/14 20:10, Sergei Shtylyov wrote:
> Hello.
>
> On 03/06/2014 09:21 PM, Ben Dooks wrote:
>
>>> Add OF match table for pci-rcar-gen2 driver for device tree support.
> [...]
>
>>> diff --git a/drivers/pci/host/pci-rcar-gen2.c
>>> b/drivers/pci/host/pci-rcar-gen2.c
>>> index fd3e3ab..1216784 100644
>>> --- a/drivers/pci/host/pci-rcar-gen2.c
>>> +++ b/drivers/pci/host/pci-rcar-gen2.c
>>> @@ -16,6 +16,7 @@
>>>   #include <linux/kernel.h>
>>>   #include <linux/module.h>
>>>   #include <linux/pci.h>
>>> +#include <linux/of_pci.h>
>>>   #include <linux/platform_device.h>
>>>   #include <linux/pm_runtime.h>
>>>   #include <linux/sizes.h>
>
>> Apologies all, there's a missing include of <linux/of.h> which should
>> have been added here
>
>     Have you ever re-posted this patch fixed? If not, it's not going to
> be merged for 3.15 I guess...

I thought I did. I can have a look a reposting it.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Ben Dooks]

On 30/03/14 20:10, Sergei Shtylyov wrote:
> Hello.
>
> On 03/06/2014 09:21 PM, Ben Dooks wrote:
>
>>> Add OF match table for pci-rcar-gen2 driver for device tree support.
> [...]
>
>>> diff --git a/drivers/pci/host/pci-rcar-gen2.c
>>> b/drivers/pci/host/pci-rcar-gen2.c
>>> index fd3e3ab..1216784 100644
>>> --- a/drivers/pci/host/pci-rcar-gen2.c
>>> +++ b/drivers/pci/host/pci-rcar-gen2.c
>>> @@ -16,6 +16,7 @@
>>>   #include <linux/kernel.h>
>>>   #include <linux/module.h>
>>>   #include <linux/pci.h>
>>> +#include <linux/of_pci.h>
>>>   #include <linux/platform_device.h>
>>>   #include <linux/pm_runtime.h>
>>>   #include <linux/sizes.h>
>
>> Apologies all, there's a missing include of <linux/of.h> which should
>> have been added here
>
>     Have you ever re-posted this patch fixed? If not, it's not going to
> be merged for 3.15 I guess...

I thought I did. I can have a look a reposting it.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Sergei Shtylyov]

Hello.

On 03/30/2014 11:21 PM, Ben Dooks wrote:

>>>> Add OF match table for pci-rcar-gen2 driver for device tree support.
>> [...]

>>>> diff --git a/drivers/pci/host/pci-rcar-gen2.c
>>>> b/drivers/pci/host/pci-rcar-gen2.c
>>>> index fd3e3ab..1216784 100644
>>>> --- a/drivers/pci/host/pci-rcar-gen2.c
>>>> +++ b/drivers/pci/host/pci-rcar-gen2.c
>>>> @@ -16,6 +16,7 @@
>>>>   #include <linux/kernel.h>
>>>>   #include <linux/module.h>
>>>>   #include <linux/pci.h>
>>>> +#include <linux/of_pci.h>
>>>>   #include <linux/platform_device.h>
>>>>   #include <linux/pm_runtime.h>
>>>>   #include <linux/sizes.h>

>>> Apologies all, there's a missing include of <linux/of.h> which should
>>> have been added here

>>     Have you ever re-posted this patch fixed? If not, it's not going to
>> be merged for 3.15 I guess...

> I thought I did.

    I don't see such repost in 'linux-sh'.

> I can have a look a reposting it.

    It doesn't apply to the current renesas.git devel branch. What tree it was 
against?

WBR, Sergei

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Sergei Shtylyov]

Hello.

On 03/30/2014 11:21 PM, Ben Dooks wrote:

>>>> Add OF match table for pci-rcar-gen2 driver for device tree support.
>> [...]

>>>> diff --git a/drivers/pci/host/pci-rcar-gen2.c
>>>> b/drivers/pci/host/pci-rcar-gen2.c
>>>> index fd3e3ab..1216784 100644
>>>> --- a/drivers/pci/host/pci-rcar-gen2.c
>>>> +++ b/drivers/pci/host/pci-rcar-gen2.c
>>>> @@ -16,6 +16,7 @@
>>>>   #include <linux/kernel.h>
>>>>   #include <linux/module.h>
>>>>   #include <linux/pci.h>
>>>> +#include <linux/of_pci.h>
>>>>   #include <linux/platform_device.h>
>>>>   #include <linux/pm_runtime.h>
>>>>   #include <linux/sizes.h>

>>> Apologies all, there's a missing include of <linux/of.h> which should
>>> have been added here

>>     Have you ever re-posted this patch fixed? If not, it's not going to
>> be merged for 3.15 I guess...

> I thought I did.

    I don't see such repost in 'linux-sh'.

> I can have a look a reposting it.

    It doesn't apply to the current renesas.git devel branch. What tree it was 
against?

WBR, Sergei

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Ben Dooks]

On 30/03/14 20:26, Sergei Shtylyov wrote:
> Hello.
>
> On 03/30/2014 11:21 PM, Ben Dooks wrote:
>
>>>>> Add OF match table for pci-rcar-gen2 driver for device tree support.
>>> [...]
>
>>>>> diff --git a/drivers/pci/host/pci-rcar-gen2.c
>>>>> b/drivers/pci/host/pci-rcar-gen2.c
>>>>> index fd3e3ab..1216784 100644
>>>>> --- a/drivers/pci/host/pci-rcar-gen2.c
>>>>> +++ b/drivers/pci/host/pci-rcar-gen2.c
>>>>> @@ -16,6 +16,7 @@
>>>>>   #include <linux/kernel.h>
>>>>>   #include <linux/module.h>
>>>>>   #include <linux/pci.h>
>>>>> +#include <linux/of_pci.h>
>>>>>   #include <linux/platform_device.h>
>>>>>   #include <linux/pm_runtime.h>
>>>>>   #include <linux/sizes.h>
>
>>>> Apologies all, there's a missing include of <linux/of.h> which should
>>>> have been added here
>
>>>     Have you ever re-posted this patch fixed? If not, it's not going to
>>> be merged for 3.15 I guess...
>
>> I thought I did.
>
>     I don't see such repost in 'linux-sh'.
>
>> I can have a look a reposting it.
>
>     It doesn't apply to the current renesas.git devel branch. What tree
> it was against?

 From my records it was against the -rc3 release of Horms' development
tree. I know Simon's tree has been closed for the board bits, but I
could re-send the rcar-pci code.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Ben Dooks]

On 30/03/14 20:26, Sergei Shtylyov wrote:
> Hello.
>
> On 03/30/2014 11:21 PM, Ben Dooks wrote:
>
>>>>> Add OF match table for pci-rcar-gen2 driver for device tree support.
>>> [...]
>
>>>>> diff --git a/drivers/pci/host/pci-rcar-gen2.c
>>>>> b/drivers/pci/host/pci-rcar-gen2.c
>>>>> index fd3e3ab..1216784 100644
>>>>> --- a/drivers/pci/host/pci-rcar-gen2.c
>>>>> +++ b/drivers/pci/host/pci-rcar-gen2.c
>>>>> @@ -16,6 +16,7 @@
>>>>>   #include <linux/kernel.h>
>>>>>   #include <linux/module.h>
>>>>>   #include <linux/pci.h>
>>>>> +#include <linux/of_pci.h>
>>>>>   #include <linux/platform_device.h>
>>>>>   #include <linux/pm_runtime.h>
>>>>>   #include <linux/sizes.h>
>
>>>> Apologies all, there's a missing include of <linux/of.h> which should
>>>> have been added here
>
>>>     Have you ever re-posted this patch fixed? If not, it's not going to
>>> be merged for 3.15 I guess...
>
>> I thought I did.
>
>     I don't see such repost in 'linux-sh'.
>
>> I can have a look a reposting it.
>
>     It doesn't apply to the current renesas.git devel branch. What tree
> it was against?

 From my records it was against the -rc3 release of Horms' development
tree. I know Simon's tree has been closed for the board bits, but I
could re-send the rcar-pci code.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Sergei Shtylyov]

On 03/30/2014 11:40 PM, Ben Dooks wrote:

>>>>>> Add OF match table for pci-rcar-gen2 driver for device tree support.
>>>> [...]

>>>>>> diff --git a/drivers/pci/host/pci-rcar-gen2.c
>>>>>> b/drivers/pci/host/pci-rcar-gen2.c
>>>>>> index fd3e3ab..1216784 100644
>>>>>> --- a/drivers/pci/host/pci-rcar-gen2.c
>>>>>> +++ b/drivers/pci/host/pci-rcar-gen2.c
>>>>>> @@ -16,6 +16,7 @@
>>>>>>   #include <linux/kernel.h>
>>>>>>   #include <linux/module.h>
>>>>>>   #include <linux/pci.h>
>>>>>> +#include <linux/of_pci.h>
>>>>>>   #include <linux/platform_device.h>
>>>>>>   #include <linux/pm_runtime.h>
>>>>>>   #include <linux/sizes.h>

>>>>> Apologies all, there's a missing include of <linux/of.h> which should
>>>>> have been added here

>>>>     Have you ever re-posted this patch fixed? If not, it's not going to
>>>> be merged for 3.15 I guess...

>>> I thought I did.

>>     I don't see such repost in 'linux-sh'.

    And neither do I see it in other lists.

>>> I can have a look a reposting it.

>>     It doesn't apply to the current renesas.git devel branch. What tree
>> it was against?

    Looks like you had some patches to the PCI driver before this one. I've 
just found something in Bjorn's pci.git repo's next branch...

>  From my records it was against the -rc3 release of Horms' development
> tree. I know Simon's tree has been closed for the board bits, but I
> could re-send the rcar-pci code.

    The patch does applies cleanly to pci.git's next branch (it has a trailing 
whitespace though), so no dire need to re-post. I'm not sure if the new 
version of the patch could still be merged there, as Linus was going to 
release 3.14 and so open the merge window this weekend.

WBR, Sergei

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Sergei Shtylyov]

On 03/30/2014 11:40 PM, Ben Dooks wrote:

>>>>>> Add OF match table for pci-rcar-gen2 driver for device tree support.
>>>> [...]

>>>>>> diff --git a/drivers/pci/host/pci-rcar-gen2.c
>>>>>> b/drivers/pci/host/pci-rcar-gen2.c
>>>>>> index fd3e3ab..1216784 100644
>>>>>> --- a/drivers/pci/host/pci-rcar-gen2.c
>>>>>> +++ b/drivers/pci/host/pci-rcar-gen2.c
>>>>>> @@ -16,6 +16,7 @@
>>>>>>   #include <linux/kernel.h>
>>>>>>   #include <linux/module.h>
>>>>>>   #include <linux/pci.h>
>>>>>> +#include <linux/of_pci.h>
>>>>>>   #include <linux/platform_device.h>
>>>>>>   #include <linux/pm_runtime.h>
>>>>>>   #include <linux/sizes.h>

>>>>> Apologies all, there's a missing include of <linux/of.h> which should
>>>>> have been added here

>>>>     Have you ever re-posted this patch fixed? If not, it's not going to
>>>> be merged for 3.15 I guess...

>>> I thought I did.

>>     I don't see such repost in 'linux-sh'.

    And neither do I see it in other lists.

>>> I can have a look a reposting it.

>>     It doesn't apply to the current renesas.git devel branch. What tree
>> it was against?

    Looks like you had some patches to the PCI driver before this one. I've 
just found something in Bjorn's pci.git repo's next branch...

>  From my records it was against the -rc3 release of Horms' development
> tree. I know Simon's tree has been closed for the board bits, but I
> could re-send the rcar-pci code.

    The patch does applies cleanly to pci.git's next branch (it has a trailing 
whitespace though), so no dire need to re-post. I'm not sure if the new 
version of the patch could still be merged there, as Linus was going to 
release 3.14 and so open the merge window this weekend.

WBR, Sergei

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Sergei Shtylyov]

Hello.

On 03/30/2014 11:40 PM, Ben Dooks wrote:

>>>>>> Add OF match table for pci-rcar-gen2 driver for device tree support.
>>>> [...]

>>>>>> diff --git a/drivers/pci/host/pci-rcar-gen2.c
>>>>>> b/drivers/pci/host/pci-rcar-gen2.c
>>>>>> index fd3e3ab..1216784 100644
>>>>>> --- a/drivers/pci/host/pci-rcar-gen2.c
>>>>>> +++ b/drivers/pci/host/pci-rcar-gen2.c
>>>>>> @@ -16,6 +16,7 @@
>>>>>>   #include <linux/kernel.h>
>>>>>>   #include <linux/module.h>
>>>>>>   #include <linux/pci.h>
>>>>>> +#include <linux/of_pci.h>
>>>>>>   #include <linux/platform_device.h>
>>>>>>   #include <linux/pm_runtime.h>
>>>>>>   #include <linux/sizes.h>

>>>>> Apologies all, there's a missing include of <linux/of.h> which should
>>>>> have been added here

>>>>     Have you ever re-posted this patch fixed? If not, it's not going to
>>>> be merged for 3.15 I guess...

>>> I thought I did.

>>     I don't see such repost in 'linux-sh'.

>>> I can have a look a reposting it.

>>     It doesn't apply to the current renesas.git devel branch. What tree
>> it was against?

>  From my records it was against the -rc3 release of Horms' development
> tree. I know Simon's tree has been closed for the board bits, but I
> could re-send the rcar-pci code.

    Could you address my comments and re-send? Or if you don't have time, 
would you mind that I take this patch into my hands?

WBR, Sergei

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Sergei Shtylyov]

Hello.

On 03/30/2014 11:40 PM, Ben Dooks wrote:

>>>>>> Add OF match table for pci-rcar-gen2 driver for device tree support.
>>>> [...]

>>>>>> diff --git a/drivers/pci/host/pci-rcar-gen2.c
>>>>>> b/drivers/pci/host/pci-rcar-gen2.c
>>>>>> index fd3e3ab..1216784 100644
>>>>>> --- a/drivers/pci/host/pci-rcar-gen2.c
>>>>>> +++ b/drivers/pci/host/pci-rcar-gen2.c
>>>>>> @@ -16,6 +16,7 @@
>>>>>>   #include <linux/kernel.h>
>>>>>>   #include <linux/module.h>
>>>>>>   #include <linux/pci.h>
>>>>>> +#include <linux/of_pci.h>
>>>>>>   #include <linux/platform_device.h>
>>>>>>   #include <linux/pm_runtime.h>
>>>>>>   #include <linux/sizes.h>

>>>>> Apologies all, there's a missing include of <linux/of.h> which should
>>>>> have been added here

>>>>     Have you ever re-posted this patch fixed? If not, it's not going to
>>>> be merged for 3.15 I guess...

>>> I thought I did.

>>     I don't see such repost in 'linux-sh'.

>>> I can have a look a reposting it.

>>     It doesn't apply to the current renesas.git devel branch. What tree
>> it was against?

>  From my records it was against the -rc3 release of Horms' development
> tree. I know Simon's tree has been closed for the board bits, but I
> could re-send the rcar-pci code.

    Could you address my comments and re-send? Or if you don't have time, 
would you mind that I take this patch into my hands?

WBR, Sergei

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Sergei Shtylyov]

On 03/06/2014 09:01 PM, Ben Dooks wrote:

> Add OF match table for pci-rcar-gen2 driver for device tree support.

> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
> ---
> Updates since v1:
> 	- moved documentation into patch
> 	- moved to using bus-range parsing
> 	- ensured usb phy can be linked to usb devices

> Cc: Bjorn Helgaas <bhelgaas@google.com>
> Cc: Simon Horman <horms@verge.net.au>
> Cc: linux-pci@vger.kernel.org
> Cc: linux-sh@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> ---
>   .../bindings/pci/renessas,pci-rcar-gen2.txt        | 52 ++++++++++++++++++++++
>   drivers/pci/host/pci-rcar-gen2.c                   | 33 +++++++++++++-
>   2 files changed, 83 insertions(+), 2 deletions(-)
>   create mode 100644 Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt

> diff --git a/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
> new file mode 100644
> index 0000000..bd6d291
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
> @@ -0,0 +1,52 @@
> +Renesas AHB to PCI bridge
> +-------------------------

    Perhaps it makes sense to describe PCIe bindings in the same file...

[...]

> +Example SoC configuration:
> +
> +	pci0: pci@ee090000  {
> +		compatible = "renesas,pci-r8a7790";
> +		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
> +		reg = <0x0 0xee090000 0x0 0xc00>,
> +		      <0x0 0xee080000 0x0 0x1100>;
> +		interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
> +		status = "disabled";
> +
> +		bus-range = <0 0>;
> +		#address-cells = <3>;
> +		#size-cells = <2>;
> +	};
> +
> +Example board setup:
> +
> +&pci1 {
> +	status = "okay";
> +	pinctrl-0 = <&usb1_pins>;
> +	pinctrl-names = "default";
> +
> +	pci@0,1 {
> +		reg = <0x800 0 0 0 0>;
> +		device_type = "pci";
> +		usb-phy = <&usbphy>;
> +	};
> +
> +	pci@0,2 {
> +		reg = <0x1000 0 0 0 0>;
> +		device_type = "pci";
> +		usb-phy = <&usbphy>;
> +	};
> +};

    As I said, these PCI sub-nodes belong to the SoC file.

> diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
> index fd3e3ab..1216784 100644
> --- a/drivers/pci/host/pci-rcar-gen2.c
> +++ b/drivers/pci/host/pci-rcar-gen2.c
[...]
> @@ -377,11 +396,21 @@ static int rcar_pci_probe(struct platform_device *pdev)
>   	return 0;
>   }
>
> +#ifdef CONFIG_OF

    I don't think it's really worth it.

> +static struct of_device_id rcar_pci_of_match[] = {
> +	{ .compatible = "renesas,pci-r8a7790", },
> +	{ },
> +};
> +
> +MODULE_DEVICE_TABLE(of, rcar_pci_of_match);
> +#endif
> +
>   static struct platform_driver rcar_pci_driver = {
>   	.driver = {
>   		.name = "pci-rcar-gen2",
>   		.owner = THIS_MODULE,
>   		.suppress_bind_attrs = true,
> +		.of_match_table = of_match_ptr(rcar_pci_of_match),

    And so, of_match_ptr() is not needed.

WBR, Sergei

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Sergei Shtylyov]

On 03/06/2014 09:01 PM, Ben Dooks wrote:

> Add OF match table for pci-rcar-gen2 driver for device tree support.

> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
> ---
> Updates since v1:
> 	- moved documentation into patch
> 	- moved to using bus-range parsing
> 	- ensured usb phy can be linked to usb devices

> Cc: Bjorn Helgaas <bhelgaas@google.com>
> Cc: Simon Horman <horms@verge.net.au>
> Cc: linux-pci@vger.kernel.org
> Cc: linux-sh@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> ---
>   .../bindings/pci/renessas,pci-rcar-gen2.txt        | 52 ++++++++++++++++++++++
>   drivers/pci/host/pci-rcar-gen2.c                   | 33 +++++++++++++-
>   2 files changed, 83 insertions(+), 2 deletions(-)
>   create mode 100644 Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt

> diff --git a/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
> new file mode 100644
> index 0000000..bd6d291
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
> @@ -0,0 +1,52 @@
> +Renesas AHB to PCI bridge
> +-------------------------

    Perhaps it makes sense to describe PCIe bindings in the same file...

[...]

> +Example SoC configuration:
> +
> +	pci0: pci@ee090000  {
> +		compatible = "renesas,pci-r8a7790";
> +		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
> +		reg = <0x0 0xee090000 0x0 0xc00>,
> +		      <0x0 0xee080000 0x0 0x1100>;
> +		interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
> +		status = "disabled";
> +
> +		bus-range = <0 0>;
> +		#address-cells = <3>;
> +		#size-cells = <2>;
> +	};
> +
> +Example board setup:
> +
> +&pci1 {
> +	status = "okay";
> +	pinctrl-0 = <&usb1_pins>;
> +	pinctrl-names = "default";
> +
> +	pci@0,1 {
> +		reg = <0x800 0 0 0 0>;
> +		device_type = "pci";
> +		usb-phy = <&usbphy>;
> +	};
> +
> +	pci@0,2 {
> +		reg = <0x1000 0 0 0 0>;
> +		device_type = "pci";
> +		usb-phy = <&usbphy>;
> +	};
> +};

    As I said, these PCI sub-nodes belong to the SoC file.

> diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
> index fd3e3ab..1216784 100644
> --- a/drivers/pci/host/pci-rcar-gen2.c
> +++ b/drivers/pci/host/pci-rcar-gen2.c
[...]
> @@ -377,11 +396,21 @@ static int rcar_pci_probe(struct platform_device *pdev)
>   	return 0;
>   }
>
> +#ifdef CONFIG_OF

    I don't think it's really worth it.

> +static struct of_device_id rcar_pci_of_match[] = {
> +	{ .compatible = "renesas,pci-r8a7790", },
> +	{ },
> +};
> +
> +MODULE_DEVICE_TABLE(of, rcar_pci_of_match);
> +#endif
> +
>   static struct platform_driver rcar_pci_driver = {
>   	.driver = {
>   		.name = "pci-rcar-gen2",
>   		.owner = THIS_MODULE,
>   		.suppress_bind_attrs = true,
> +		.of_match_table = of_match_ptr(rcar_pci_of_match),

    And so, of_match_ptr() is not needed.

WBR, Sergei

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Bjorn Helgaas]

On Thu, Mar 06, 2014 at 06:01:19PM +0000, Ben Dooks wrote:
> Add OF match table for pci-rcar-gen2 driver for device tree support.
> 
> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

I'm not sure what the status of this is.  I saw comments about a missing
#include, but I didn't see a fixed repost.  Ben, could you please repost
anything you have outstanding for me?

> ---
> Updates since v1:
> 	- moved documentation into patch
> 	- moved to using bus-range parsing
> 	- ensured usb phy can be linked to usb devices
> 
> Cc: Bjorn Helgaas <bhelgaas@google.com>
> Cc: Simon Horman <horms@verge.net.au>
> Cc: linux-pci@vger.kernel.org
> Cc: linux-sh@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> ---
>  .../bindings/pci/renessas,pci-rcar-gen2.txt        | 52 ++++++++++++++++++++++
>  drivers/pci/host/pci-rcar-gen2.c                   | 33 +++++++++++++-
>  2 files changed, 83 insertions(+), 2 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
> 
> diff --git a/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
> new file mode 100644
> index 0000000..bd6d291
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
> @@ -0,0 +1,52 @@
> +Renesas AHB to PCI bridge
> +-------------------------
> +
> +This is the bridge used internally to connect the USB controllers to the
> +AHB. There is one bridge instance per USB port consiting of an internal
> +OHCI and EHCI controller.
> +
> +Required properties:
> + - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC
> + - reg : A list of physical regions to access the device. The first is
> +         the operational registers for the OHCI/EHCI controller and the
> +	 second region is for the bridge configuration and control registers.
> + - interrupts : interrupt for the device
> + - clocks : The reference to the device clock
> + - bus-range: The PCI bus number ranges. As this is a single bus, the range
> +		should be specified as the same value twice.
> +
> +
> +Example SoC configuration:
> +
> +	pci0: pci@ee090000  {
> +		compatible = "renesas,pci-r8a7790";
> +		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
> +		reg = <0x0 0xee090000 0x0 0xc00>,
> +		      <0x0 0xee080000 0x0 0x1100>;
> +		interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
> +		status = "disabled";
> +
> +		bus-range = <0 0>;
> +		#address-cells = <3>;
> +		#size-cells = <2>;
> +	};
> +
> +Example board setup:
> +
> +&pci1 {
> +	status = "okay";
> +	pinctrl-0 = <&usb1_pins>;
> +	pinctrl-names = "default";
> +
> +	pci@0,1 {
> +		reg = <0x800 0 0 0 0>;
> +		device_type = "pci";
> +		usb-phy = <&usbphy>;
> +	};
> +
> +	pci@0,2 {
> +		reg = <0x1000 0 0 0 0>;
> +		device_type = "pci";
> +		usb-phy = <&usbphy>;
> +	};
> +};
> diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
> index fd3e3ab..1216784 100644
> --- a/drivers/pci/host/pci-rcar-gen2.c
> +++ b/drivers/pci/host/pci-rcar-gen2.c
> @@ -16,6 +16,7 @@
>  #include <linux/kernel.h>
>  #include <linux/module.h>
>  #include <linux/pci.h>
> +#include <linux/of_pci.h>
>  #include <linux/platform_device.h>
>  #include <linux/pm_runtime.h>
>  #include <linux/sizes.h>
> @@ -98,6 +99,7 @@ struct rcar_pci_priv {
>  	struct resource io_res;
>  	struct resource mem_res;
>  	struct resource *cfg_res;
> +	unsigned busnr;
>  	int irq;
>  	unsigned long window_size;
>  };
> @@ -312,8 +314,8 @@ static int rcar_pci_setup(int nr, struct pci_sys_data *sys)
>  	pci_add_resource(&sys->resources, &priv->io_res);
>  	pci_add_resource(&sys->resources, &priv->mem_res);
>  
> -	/* Setup bus number based on platform device id */
> -	sys->busnr = to_platform_device(priv->dev)->id;
> +	/* Setup bus number based on platform device id / of bus-range */
> +	sys->busnr = priv->busnr;
>  	return 1;
>  }
>  
> @@ -366,6 +368,23 @@ static int rcar_pci_probe(struct platform_device *pdev)
>  
>  	priv->window_size = SZ_1G;
>  
> +	if (pdev->dev.of_node) {
> +		struct resource busnr;
> +		int ret;
> +
> +		ret = of_pci_parse_bus_range(pdev->dev.of_node, &busnr);
> +		if (ret < 0) {
> +			dev_err(&pdev->dev, "failed to parse bus-range\n");
> +			return ret;
> +		}
> +		
> +		priv->busnr = busnr.start;
> +		if (busnr.end != busnr.start)
> +			dev_warn(&pdev->dev, "only one bus number supported\n");
> +	} else {
> +		priv->busnr = pdev->id;
> +	}
> +
>  	hw_private[0] = priv;
>  	memset(&hw, 0, sizeof(hw));
>  	hw.nr_controllers = ARRAY_SIZE(hw_private);
> @@ -377,11 +396,21 @@ static int rcar_pci_probe(struct platform_device *pdev)
>  	return 0;
>  }
>  
> +#ifdef CONFIG_OF
> +static struct of_device_id rcar_pci_of_match[] = {
> +	{ .compatible = "renesas,pci-r8a7790", },
> +	{ },
> +};
> +
> +MODULE_DEVICE_TABLE(of, rcar_pci_of_match);
> +#endif
> +
>  static struct platform_driver rcar_pci_driver = {
>  	.driver = {
>  		.name = "pci-rcar-gen2",
>  		.owner = THIS_MODULE,
>  		.suppress_bind_attrs = true,
> +		.of_match_table = of_match_ptr(rcar_pci_of_match),
>  	},
>  	.probe = rcar_pci_probe,
>  };
> -- 
> 1.9.0
> 

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Bjorn Helgaas]

On Thu, Mar 06, 2014 at 06:01:19PM +0000, Ben Dooks wrote:
> Add OF match table for pci-rcar-gen2 driver for device tree support.
> 
> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

I'm not sure what the status of this is.  I saw comments about a missing
#include, but I didn't see a fixed repost.  Ben, could you please repost
anything you have outstanding for me?

> ---
> Updates since v1:
> 	- moved documentation into patch
> 	- moved to using bus-range parsing
> 	- ensured usb phy can be linked to usb devices
> 
> Cc: Bjorn Helgaas <bhelgaas@google.com>
> Cc: Simon Horman <horms@verge.net.au>
> Cc: linux-pci@vger.kernel.org
> Cc: linux-sh@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> ---
>  .../bindings/pci/renessas,pci-rcar-gen2.txt        | 52 ++++++++++++++++++++++
>  drivers/pci/host/pci-rcar-gen2.c                   | 33 +++++++++++++-
>  2 files changed, 83 insertions(+), 2 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
> 
> diff --git a/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
> new file mode 100644
> index 0000000..bd6d291
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/renessas,pci-rcar-gen2.txt
> @@ -0,0 +1,52 @@
> +Renesas AHB to PCI bridge
> +-------------------------
> +
> +This is the bridge used internally to connect the USB controllers to the
> +AHB. There is one bridge instance per USB port consiting of an internal
> +OHCI and EHCI controller.
> +
> +Required properties:
> + - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC
> + - reg : A list of physical regions to access the device. The first is
> +         the operational registers for the OHCI/EHCI controller and the
> +	 second region is for the bridge configuration and control registers.
> + - interrupts : interrupt for the device
> + - clocks : The reference to the device clock
> + - bus-range: The PCI bus number ranges. As this is a single bus, the range
> +		should be specified as the same value twice.
> +
> +
> +Example SoC configuration:
> +
> +	pci0: pci@ee090000  {
> +		compatible = "renesas,pci-r8a7790";
> +		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
> +		reg = <0x0 0xee090000 0x0 0xc00>,
> +		      <0x0 0xee080000 0x0 0x1100>;
> +		interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
> +		status = "disabled";
> +
> +		bus-range = <0 0>;
> +		#address-cells = <3>;
> +		#size-cells = <2>;
> +	};
> +
> +Example board setup:
> +
> +&pci1 {
> +	status = "okay";
> +	pinctrl-0 = <&usb1_pins>;
> +	pinctrl-names = "default";
> +
> +	pci@0,1 {
> +		reg = <0x800 0 0 0 0>;
> +		device_type = "pci";
> +		usb-phy = <&usbphy>;
> +	};
> +
> +	pci@0,2 {
> +		reg = <0x1000 0 0 0 0>;
> +		device_type = "pci";
> +		usb-phy = <&usbphy>;
> +	};
> +};
> diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
> index fd3e3ab..1216784 100644
> --- a/drivers/pci/host/pci-rcar-gen2.c
> +++ b/drivers/pci/host/pci-rcar-gen2.c
> @@ -16,6 +16,7 @@
>  #include <linux/kernel.h>
>  #include <linux/module.h>
>  #include <linux/pci.h>
> +#include <linux/of_pci.h>
>  #include <linux/platform_device.h>
>  #include <linux/pm_runtime.h>
>  #include <linux/sizes.h>
> @@ -98,6 +99,7 @@ struct rcar_pci_priv {
>  	struct resource io_res;
>  	struct resource mem_res;
>  	struct resource *cfg_res;
> +	unsigned busnr;
>  	int irq;
>  	unsigned long window_size;
>  };
> @@ -312,8 +314,8 @@ static int rcar_pci_setup(int nr, struct pci_sys_data *sys)
>  	pci_add_resource(&sys->resources, &priv->io_res);
>  	pci_add_resource(&sys->resources, &priv->mem_res);
>  
> -	/* Setup bus number based on platform device id */
> -	sys->busnr = to_platform_device(priv->dev)->id;
> +	/* Setup bus number based on platform device id / of bus-range */
> +	sys->busnr = priv->busnr;
>  	return 1;
>  }
>  
> @@ -366,6 +368,23 @@ static int rcar_pci_probe(struct platform_device *pdev)
>  
>  	priv->window_size = SZ_1G;
>  
> +	if (pdev->dev.of_node) {
> +		struct resource busnr;
> +		int ret;
> +
> +		ret = of_pci_parse_bus_range(pdev->dev.of_node, &busnr);
> +		if (ret < 0) {
> +			dev_err(&pdev->dev, "failed to parse bus-range\n");
> +			return ret;
> +		}
> +		
> +		priv->busnr = busnr.start;
> +		if (busnr.end != busnr.start)
> +			dev_warn(&pdev->dev, "only one bus number supported\n");
> +	} else {
> +		priv->busnr = pdev->id;
> +	}
> +
>  	hw_private[0] = priv;
>  	memset(&hw, 0, sizeof(hw));
>  	hw.nr_controllers = ARRAY_SIZE(hw_private);
> @@ -377,11 +396,21 @@ static int rcar_pci_probe(struct platform_device *pdev)
>  	return 0;
>  }
>  
> +#ifdef CONFIG_OF
> +static struct of_device_id rcar_pci_of_match[] = {
> +	{ .compatible = "renesas,pci-r8a7790", },
> +	{ },
> +};
> +
> +MODULE_DEVICE_TABLE(of, rcar_pci_of_match);
> +#endif
> +
>  static struct platform_driver rcar_pci_driver = {
>  	.driver = {
>  		.name = "pci-rcar-gen2",
>  		.owner = THIS_MODULE,
>  		.suppress_bind_attrs = true,
> +		.of_match_table = of_match_ptr(rcar_pci_of_match),
>  	},
>  	.probe = rcar_pci_probe,
>  };
> -- 
> 1.9.0
> 

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Ben Dooks]

On 04/04/14 18:09, Bjorn Helgaas wrote:
> On Thu, Mar 06, 2014 at 06:01:19PM +0000, Ben Dooks wrote:
>> Add OF match table for pci-rcar-gen2 driver for device tree support.
>>
>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>
> I'm not sure what the status of this is.  I saw comments about a missing
> #include, but I didn't see a fixed repost.  Ben, could you please repost
> anything you have outstanding for me?

Sergei was going to re-post this series. I can have a look at
re-sending this later today if he hasn't already sorted it out.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Ben Dooks]

On 04/04/14 18:09, Bjorn Helgaas wrote:
> On Thu, Mar 06, 2014 at 06:01:19PM +0000, Ben Dooks wrote:
>> Add OF match table for pci-rcar-gen2 driver for device tree support.
>>
>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>
> I'm not sure what the status of this is.  I saw comments about a missing
> #include, but I didn't see a fixed repost.  Ben, could you please repost
> anything you have outstanding for me?

Sergei was going to re-post this series. I can have a look at
re-sending this later today if he hasn't already sorted it out.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Ben Dooks]

On 04/04/14 18:09, Bjorn Helgaas wrote:
> On Thu, Mar 06, 2014 at 06:01:19PM +0000, Ben Dooks wrote:
>> Add OF match table for pci-rcar-gen2 driver for device tree support.
>>
>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>
> I'm not sure what the status of this is.  I saw comments about a missing
> #include, but I didn't see a fixed repost.  Ben, could you please repost
> anything you have outstanding for me?

Sergei was going to re-post this series. I can have a look at
re-sending this later today if he hasn't already sorted it out.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Sergei Shtylyov]

Hello.

On 04/04/2014 09:09 PM, Bjorn Helgaas wrote:

>> Add OF match table for pci-rcar-gen2 driver for device tree support.

>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

> I'm not sure what the status of this is.  I saw comments about a missing
> #include, but I didn't see a fixed repost.

    Since there was none. :-)

> Ben, could you please repost anything you have outstanding for me?

    I took updating this patch into my hands with Ben's consent, so I'll 
repost it soonish.

WBR, Sergei

Re: [PATCH 1/9] pci-rcar-gen2: add devicetree support

[Sergei Shtylyov]

Hello.

On 04/04/2014 09:09 PM, Bjorn Helgaas wrote:

>> Add OF match table for pci-rcar-gen2 driver for device tree support.

>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

> I'm not sure what the status of this is.  I saw comments about a missing
> #include, but I didn't see a fixed repost.

    Since there was none. :-)

> Ben, could you please repost anything you have outstanding for me?

    I took updating this patch into my hands with Ben's consent, so I'll 
repost it soonish.

WBR, Sergei

[PATCH 3/9] phy-rcar-usb-gen2: add device tree support

Add support for the phy-rcar-gen2-usb driver to be probed from device tree.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Fixes from v2:
	- fix missed of_match_ptr()
	- fix names of channel selection booleans
	- updated and merged documentation for dt entries

Fixes from v2:
	- fix missing of_if patch

Fixes from v1:
	- use of_property_reasd-bool()
	- remove unused of_id variable

Cc: Felipe Balbi <balbi@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: devicetree@vger.kernel.org

Conflicts:
	drivers/usb/phy/phy-rcar-gen2-usb.c
---
 .../bindings/usb/renesas,rcar-gen2-usb-phy.txt     | 36 ++++++++++++++++++++++
 drivers/pci/host/pci-rcar-gen2.c                   |  1 +
 drivers/usb/phy/phy-rcar-gen2-usb.c                | 34 +++++++++++++++++---
 3 files changed, 66 insertions(+), 5 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt

diff --git a/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
new file mode 100644
index 0000000..5351a30
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
@@ -0,0 +1,36 @@
+Renesas RCar gen2 USB PHY bindings
+----------------------------------
+
+Bindings for the USB PHY block used in some Renesas SoCs.
+
+Required properties:
+ - compatible:  "renesas,usb-phy-r8a7790" for the R8A7790 SoC
+		"renesas,usb-phy-r8a7791" for the R8A7791 SoC
+ - reg : A single region to access device registers
+ - clocks : The reference to the clock to use for this block
+ - clock-names : The name for the clock at index 0 (must be "usbhs")
+
+Optional properties:
+
+ - renesas,usb0-device: boolean, if present USB0 is connected to HS device
+			otherwise the USB0 is connected to OHCI/EHCI host.
+ - renesas,usb2-xhci: boolean, if present USB2 is connected to XHCI controller
+		      otherwise the USB2 is connected to OHCI/EHCI host.
+
+
+Example device node for SoC dtsi file:
+
+	usbphy: usbphy@e6590100 {
+		compatible = "renesas,usb-phy-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
+		clock-names = "usbhs";
+		reg = < 0x0 0xe6590100 0x0 0x100>;
+		status = "disabled";
+	};
+
+Example board file:
+
+&usbphy {
+	status = "okay";
+};
+
diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
index 1216784..2595078 100644
--- a/drivers/pci/host/pci-rcar-gen2.c
+++ b/drivers/pci/host/pci-rcar-gen2.c
@@ -15,6 +15,7 @@
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/pci.h>
 #include <linux/of_pci.h>
 #include <linux/platform_device.h>
diff --git a/drivers/usb/phy/phy-rcar-gen2-usb.c b/drivers/usb/phy/phy-rcar-gen2-usb.c
index 388d89f..8006c3c 100644
--- a/drivers/usb/phy/phy-rcar-gen2-usb.c
+++ b/drivers/usb/phy/phy-rcar-gen2-usb.c
@@ -15,6 +15,7 @@
 #include <linux/module.h>
 #include <linux/platform_data/usb-rcar-gen2-phy.h>
 #include <linux/platform_device.h>
+#include <linux/of_device.h>
 #include <linux/spinlock.h>
 #include <linux/usb/otg.h>
 
@@ -167,6 +168,15 @@ out:
 	spin_unlock_irqrestore(&priv->lock, flags);
 }
 
+#ifdef CONFIG_OF
+static struct of_device_id rcar_gen2_usb_phy_ofmatch[] = {
+	{ .compatible = "renesas,usb-phy-r8a7790", },
+	{ .compatible = "renesas,usb-phy-r8a7791", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, rcar_gen2_usb_phy_ofmatch);
+#endif
+
 static int rcar_gen2_usb_phy_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -178,7 +188,7 @@ static int rcar_gen2_usb_phy_probe(struct platform_device *pdev)
 	int retval;
 
 	pdata = dev_get_platdata(dev);
-	if (!pdata) {
+	if (!pdata && !dev->of_node) {
 		dev_err(dev, "No platform data\n");
 		return -EINVAL;
 	}
@@ -203,16 +213,29 @@ static int rcar_gen2_usb_phy_probe(struct platform_device *pdev)
 	spin_lock_init(&priv->lock);
 	priv->clk = clk;
 	priv->base = base;
-	priv->ugctrl2 = pdata->chan0_pci ?
-			USBHS_UGCTRL2_USB0_PCI : USBHS_UGCTRL2_USB0_HS;
-	priv->ugctrl2 |= pdata->chan2_pci ?
-			USBHS_UGCTRL2_USB2_PCI : USBHS_UGCTRL2_USB2_SS;
 	priv->phy.dev = dev;
 	priv->phy.label = dev_name(dev);
 	priv->phy.init = rcar_gen2_usb_phy_init;
 	priv->phy.shutdown = rcar_gen2_usb_phy_shutdown;
 	priv->phy.set_suspend = rcar_gen2_usb_phy_set_suspend;
 
+	if (dev->of_node) {
+		if (of_property_read_bool(dev->of_node, "renesas,usb0-device"))
+			priv->ugctrl2 = USBHS_UGCTRL2_USB0_HS;
+		else
+			priv->ugctrl2 = USBHS_UGCTRL2_USB0_PCI;
+
+		if (of_property_read_bool(dev->of_node, "renesas,usb2-xhci"))
+			priv->ugctrl2 |= USBHS_UGCTRL2_USB2_SS;
+		else
+			priv->ugctrl2 |= USBHS_UGCTRL2_USB2_PCI;
+	} else {
+		priv->ugctrl2 = pdata->chan0_pci ?
+			USBHS_UGCTRL2_USB0_PCI : USBHS_UGCTRL2_USB0_HS;
+		priv->ugctrl2 |= pdata->chan2_pci ?
+			USBHS_UGCTRL2_USB2_PCI : USBHS_UGCTRL2_USB2_SS;
+	}
+
 	retval = usb_add_phy_dev(&priv->phy);
 	if (retval < 0) {
 		dev_err(dev, "Failed to add USB phy\n");
@@ -236,6 +259,7 @@ static int rcar_gen2_usb_phy_remove(struct platform_device *pdev)
 static struct platform_driver rcar_gen2_usb_phy_driver = {
 	.driver = {
 		.name = "usb_phy_rcar_gen2",
+		.of_match_table = of_match_ptr(rcar_gen2_usb_phy_ofmatch),
 	},
 	.probe = rcar_gen2_usb_phy_probe,
 	.remove = rcar_gen2_usb_phy_remove,
-- 
1.9.0

[PATCH 3/9] phy-rcar-usb-gen2: add device tree support

[Ben Dooks]

Add support for the phy-rcar-gen2-usb driver to be probed from device tree.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Fixes from v2:
	- fix missed of_match_ptr()
	- fix names of channel selection booleans
	- updated and merged documentation for dt entries

Fixes from v2:
	- fix missing of_if patch

Fixes from v1:
	- use of_property_reasd-bool()
	- remove unused of_id variable

Cc: Felipe Balbi <balbi@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: devicetree@vger.kernel.org

Conflicts:
	drivers/usb/phy/phy-rcar-gen2-usb.c
---
 .../bindings/usb/renesas,rcar-gen2-usb-phy.txt     | 36 ++++++++++++++++++++++
 drivers/pci/host/pci-rcar-gen2.c                   |  1 +
 drivers/usb/phy/phy-rcar-gen2-usb.c                | 34 +++++++++++++++++---
 3 files changed, 66 insertions(+), 5 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt

diff --git a/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
new file mode 100644
index 0000000..5351a30
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
@@ -0,0 +1,36 @@
+Renesas RCar gen2 USB PHY bindings
+----------------------------------
+
+Bindings for the USB PHY block used in some Renesas SoCs.
+
+Required properties:
+ - compatible:  "renesas,usb-phy-r8a7790" for the R8A7790 SoC
+		"renesas,usb-phy-r8a7791" for the R8A7791 SoC
+ - reg : A single region to access device registers
+ - clocks : The reference to the clock to use for this block
+ - clock-names : The name for the clock at index 0 (must be "usbhs")
+
+Optional properties:
+
+ - renesas,usb0-device: boolean, if present USB0 is connected to HS device
+			otherwise the USB0 is connected to OHCI/EHCI host.
+ - renesas,usb2-xhci: boolean, if present USB2 is connected to XHCI controller
+		      otherwise the USB2 is connected to OHCI/EHCI host.
+
+
+Example device node for SoC dtsi file:
+
+	usbphy: usbphy@e6590100 {
+		compatible = "renesas,usb-phy-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
+		clock-names = "usbhs";
+		reg = < 0x0 0xe6590100 0x0 0x100>;
+		status = "disabled";
+	};
+
+Example board file:
+
+&usbphy {
+	status = "okay";
+};
+
diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
index 1216784..2595078 100644
--- a/drivers/pci/host/pci-rcar-gen2.c
+++ b/drivers/pci/host/pci-rcar-gen2.c
@@ -15,6 +15,7 @@
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/pci.h>
 #include <linux/of_pci.h>
 #include <linux/platform_device.h>
diff --git a/drivers/usb/phy/phy-rcar-gen2-usb.c b/drivers/usb/phy/phy-rcar-gen2-usb.c
index 388d89f..8006c3c 100644
--- a/drivers/usb/phy/phy-rcar-gen2-usb.c
+++ b/drivers/usb/phy/phy-rcar-gen2-usb.c
@@ -15,6 +15,7 @@
 #include <linux/module.h>
 #include <linux/platform_data/usb-rcar-gen2-phy.h>
 #include <linux/platform_device.h>
+#include <linux/of_device.h>
 #include <linux/spinlock.h>
 #include <linux/usb/otg.h>
 
@@ -167,6 +168,15 @@ out:
 	spin_unlock_irqrestore(&priv->lock, flags);
 }
 
+#ifdef CONFIG_OF
+static struct of_device_id rcar_gen2_usb_phy_ofmatch[] = {
+	{ .compatible = "renesas,usb-phy-r8a7790", },
+	{ .compatible = "renesas,usb-phy-r8a7791", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, rcar_gen2_usb_phy_ofmatch);
+#endif
+
 static int rcar_gen2_usb_phy_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -178,7 +188,7 @@ static int rcar_gen2_usb_phy_probe(struct platform_device *pdev)
 	int retval;
 
 	pdata = dev_get_platdata(dev);
-	if (!pdata) {
+	if (!pdata && !dev->of_node) {
 		dev_err(dev, "No platform data\n");
 		return -EINVAL;
 	}
@@ -203,16 +213,29 @@ static int rcar_gen2_usb_phy_probe(struct platform_device *pdev)
 	spin_lock_init(&priv->lock);
 	priv->clk = clk;
 	priv->base = base;
-	priv->ugctrl2 = pdata->chan0_pci ?
-			USBHS_UGCTRL2_USB0_PCI : USBHS_UGCTRL2_USB0_HS;
-	priv->ugctrl2 |= pdata->chan2_pci ?
-			USBHS_UGCTRL2_USB2_PCI : USBHS_UGCTRL2_USB2_SS;
 	priv->phy.dev = dev;
 	priv->phy.label = dev_name(dev);
 	priv->phy.init = rcar_gen2_usb_phy_init;
 	priv->phy.shutdown = rcar_gen2_usb_phy_shutdown;
 	priv->phy.set_suspend = rcar_gen2_usb_phy_set_suspend;
 
+	if (dev->of_node) {
+		if (of_property_read_bool(dev->of_node, "renesas,usb0-device"))
+			priv->ugctrl2 = USBHS_UGCTRL2_USB0_HS;
+		else
+			priv->ugctrl2 = USBHS_UGCTRL2_USB0_PCI;
+
+		if (of_property_read_bool(dev->of_node, "renesas,usb2-xhci"))
+			priv->ugctrl2 |= USBHS_UGCTRL2_USB2_SS;
+		else
+			priv->ugctrl2 |= USBHS_UGCTRL2_USB2_PCI;
+	} else {
+		priv->ugctrl2 = pdata->chan0_pci ?
+			USBHS_UGCTRL2_USB0_PCI : USBHS_UGCTRL2_USB0_HS;
+		priv->ugctrl2 |= pdata->chan2_pci ?
+			USBHS_UGCTRL2_USB2_PCI : USBHS_UGCTRL2_USB2_SS;
+	}
+
 	retval = usb_add_phy_dev(&priv->phy);
 	if (retval < 0) {
 		dev_err(dev, "Failed to add USB phy\n");
@@ -236,6 +259,7 @@ static int rcar_gen2_usb_phy_remove(struct platform_device *pdev)
 static struct platform_driver rcar_gen2_usb_phy_driver = {
 	.driver = {
 		.name = "usb_phy_rcar_gen2",
+		.of_match_table = of_match_ptr(rcar_gen2_usb_phy_ofmatch),
 	},
 	.probe = rcar_gen2_usb_phy_probe,
 	.remove = rcar_gen2_usb_phy_remove,
-- 
1.9.0

Re: [PATCH 3/9] phy-rcar-usb-gen2: add device tree support

[Sergei Shtylyov]

Hello.

On 03/06/2014 09:01 PM, Ben Dooks wrote:

> Add support for the phy-rcar-gen2-usb driver to be probed from device tree.

> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
> ---
> Fixes from v2:
> 	- fix missed of_match_ptr()
> 	- fix names of channel selection booleans
> 	- updated and merged documentation for dt entries
>
> Fixes from v2:
> 	- fix missing of_if patch
>
> Fixes from v1:
> 	- use of_property_reasd-bool()
> 	- remove unused of_id variable
>
> Cc: Felipe Balbi <balbi@ti.com>
> Cc: linux-usb@vger.kernel.org
> Cc: linux-sh@vger.kernel.org
> Cc: Magnus Damm <magnus.damm@gmail.com>
> Cc: Simon Horman <horms@verge.net.au>
> Cc: devicetree@vger.kernel.org

> Conflicts:
> 	drivers/usb/phy/phy-rcar-gen2-usb.c
> ---
>   .../bindings/usb/renesas,rcar-gen2-usb-phy.txt     | 36 ++++++++++++++++++++++
>   drivers/pci/host/pci-rcar-gen2.c                   |  1 +

    Eh? What does this file have to do with USB PHY?

>   drivers/usb/phy/phy-rcar-gen2-usb.c                | 34 +++++++++++++++++---
>   3 files changed, 66 insertions(+), 5 deletions(-)
>   create mode 100644 Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt

> diff --git a/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
> new file mode 100644
> index 0000000..5351a30
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
> @@ -0,0 +1,36 @@
> +Renesas RCar gen2 USB PHY bindings
> +----------------------------------
> +
> +Bindings for the USB PHY block used in some Renesas SoCs.
> +
> +Required properties:
> + - compatible:  "renesas,usb-phy-r8a7790" for the R8A7790 SoC
> +		"renesas,usb-phy-r8a7791" for the R8A7791 SoC
> + - reg : A single region to access device registers
> + - clocks : The reference to the clock to use for this block
> + - clock-names : The name for the clock at index 0 (must be "usbhs")
> +
> +Optional properties:
> +
> + - renesas,usb0-device: boolean, if present USB0 is connected to HS device
> +			otherwise the USB0 is connected to OHCI/EHCI host.

    IIUC, the testing has shown that USBHS is dual-role controller in that 
case, i.e. supports both host and device roles (the manual has the host 
controller details too). Vladimir, is it so?

> + - renesas,usb2-xhci: boolean, if present USB2 is connected to XHCI controller
> +		      otherwise the USB2 is connected to OHCI/EHCI host.
> +
> +
> +Example device node for SoC dtsi file:
> +
> +	usbphy: usbphy@e6590100 {
> +		compatible = "renesas,usb-phy-r8a7790";
> +		clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
> +		clock-names = "usbhs";
> +		reg = < 0x0 0xe6590100 0x0 0x100>;
> +		status = "disabled";
> +	};
> +
> +Example board file:
> +
> +&usbphy {
> +	status = "okay";
> +};

    These are usually merged into one node for the example.

WBR, Sergei

Re: [PATCH 3/9] phy-rcar-usb-gen2: add device tree support

[Sergei Shtylyov]

Hello.

On 03/06/2014 09:01 PM, Ben Dooks wrote:

> Add support for the phy-rcar-gen2-usb driver to be probed from device tree.

> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
> ---
> Fixes from v2:
> 	- fix missed of_match_ptr()
> 	- fix names of channel selection booleans
> 	- updated and merged documentation for dt entries
>
> Fixes from v2:
> 	- fix missing of_if patch
>
> Fixes from v1:
> 	- use of_property_reasd-bool()
> 	- remove unused of_id variable
>
> Cc: Felipe Balbi <balbi@ti.com>
> Cc: linux-usb@vger.kernel.org
> Cc: linux-sh@vger.kernel.org
> Cc: Magnus Damm <magnus.damm@gmail.com>
> Cc: Simon Horman <horms@verge.net.au>
> Cc: devicetree@vger.kernel.org

> Conflicts:
> 	drivers/usb/phy/phy-rcar-gen2-usb.c
> ---
>   .../bindings/usb/renesas,rcar-gen2-usb-phy.txt     | 36 ++++++++++++++++++++++
>   drivers/pci/host/pci-rcar-gen2.c                   |  1 +

    Eh? What does this file have to do with USB PHY?

>   drivers/usb/phy/phy-rcar-gen2-usb.c                | 34 +++++++++++++++++---
>   3 files changed, 66 insertions(+), 5 deletions(-)
>   create mode 100644 Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt

> diff --git a/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
> new file mode 100644
> index 0000000..5351a30
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
> @@ -0,0 +1,36 @@
> +Renesas RCar gen2 USB PHY bindings
> +----------------------------------
> +
> +Bindings for the USB PHY block used in some Renesas SoCs.
> +
> +Required properties:
> + - compatible:  "renesas,usb-phy-r8a7790" for the R8A7790 SoC
> +		"renesas,usb-phy-r8a7791" for the R8A7791 SoC
> + - reg : A single region to access device registers
> + - clocks : The reference to the clock to use for this block
> + - clock-names : The name for the clock at index 0 (must be "usbhs")
> +
> +Optional properties:
> +
> + - renesas,usb0-device: boolean, if present USB0 is connected to HS device
> +			otherwise the USB0 is connected to OHCI/EHCI host.

    IIUC, the testing has shown that USBHS is dual-role controller in that 
case, i.e. supports both host and device roles (the manual has the host 
controller details too). Vladimir, is it so?

> + - renesas,usb2-xhci: boolean, if present USB2 is connected to XHCI controller
> +		      otherwise the USB2 is connected to OHCI/EHCI host.
> +
> +
> +Example device node for SoC dtsi file:
> +
> +	usbphy: usbphy@e6590100 {
> +		compatible = "renesas,usb-phy-r8a7790";
> +		clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
> +		clock-names = "usbhs";
> +		reg = < 0x0 0xe6590100 0x0 0x100>;
> +		status = "disabled";
> +	};
> +
> +Example board file:
> +
> +&usbphy {
> +	status = "okay";
> +};

    These are usually merged into one node for the example.

WBR, Sergei

Re: [PATCH 3/9] phy-rcar-usb-gen2: add device tree support

[Ben Dooks]

On 06/03/14 19:16, Sergei Shtylyov wrote:
> Hello.
>
> On 03/06/2014 09:01 PM, Ben Dooks wrote:
>
>> Add support for the phy-rcar-gen2-usb driver to be probed from device
>> tree.
>
>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
>> ---
>> Fixes from v2:
>>     - fix missed of_match_ptr()
>>     - fix names of channel selection booleans
>>     - updated and merged documentation for dt entries
>>
>> Fixes from v2:
>>     - fix missing of_if patch
>>
>> Fixes from v1:
>>     - use of_property_reasd-bool()
>>     - remove unused of_id variable
>>
>> Cc: Felipe Balbi <balbi@ti.com>
>> Cc: linux-usb@vger.kernel.org
>> Cc: linux-sh@vger.kernel.org
>> Cc: Magnus Damm <magnus.damm@gmail.com>
>> Cc: Simon Horman <horms@verge.net.au>
>> Cc: devicetree@vger.kernel.org
>
>> Conflicts:
>>     drivers/usb/phy/phy-rcar-gen2-usb.c
>> ---
>>   .../bindings/usb/renesas,rcar-gen2-usb-phy.txt     | 36
>> ++++++++++++++++++++++
>>   drivers/pci/host/pci-rcar-gen2.c                   |  1 +
>
>     Eh? What does this file have to do with USB PHY?

Ah, it was a fixup for a missing header that got merged
into the wrong file. Will fix that.

>>   drivers/usb/phy/phy-rcar-gen2-usb.c                | 34
>> +++++++++++++++++---
>>   3 files changed, 66 insertions(+), 5 deletions(-)
>>   create mode 100644
>> Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
>
>> diff --git
>> a/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
>> b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
>> new file mode 100644
>> index 0000000..5351a30
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
>> @@ -0,0 +1,36 @@
>> +Renesas RCar gen2 USB PHY bindings
>> +----------------------------------
>> +
>> +Bindings for the USB PHY block used in some Renesas SoCs.
>> +
>> +Required properties:
>> + - compatible:  "renesas,usb-phy-r8a7790" for the R8A7790 SoC
>> +        "renesas,usb-phy-r8a7791" for the R8A7791 SoC
>> + - reg : A single region to access device registers
>> + - clocks : The reference to the clock to use for this block
>> + - clock-names : The name for the clock at index 0 (must be "usbhs")
>> +
>> +Optional properties:
>> +
>> + - renesas,usb0-device: boolean, if present USB0 is connected to HS
>> device
>> +            otherwise the USB0 is connected to OHCI/EHCI host.
>
>     IIUC, the testing has shown that USBHS is dual-role controller in
> that case, i.e. supports both host and device roles (the manual has the
> host controller details too). Vladimir, is it so?

Currently there is no auto-detection for this, so it gets set at
start time.

>> + - renesas,usb2-xhci: boolean, if present USB2 is connected to XHCI
>> controller
>> +              otherwise the USB2 is connected to OHCI/EHCI host.
>> +
>> +
>> +Example device node for SoC dtsi file:
>> +
>> +    usbphy: usbphy@e6590100 {
>> +        compatible = "renesas,usb-phy-r8a7790";
>> +        clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
>> +        clock-names = "usbhs";
>> +        reg = < 0x0 0xe6590100 0x0 0x100>;
>> +        status = "disabled";
>> +    };
>> +
>> +Example board file:
>> +
>> +&usbphy {
>> +    status = "okay";
>> +};
>
>     These are usually merged into one node for the example.

Much nicer if separate.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

Re: [PATCH 3/9] phy-rcar-usb-gen2: add device tree support

[Sergei Shtylyov]

Hello.

On 03/06/2014 09:19 PM, Ben Dooks wrote:

>>> Add support for the phy-rcar-gen2-usb driver to be probed from device
>>> tree.

>>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>>> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
[...]

>>>   drivers/usb/phy/phy-rcar-gen2-usb.c                | 34
>>> +++++++++++++++++---
>>>   3 files changed, 66 insertions(+), 5 deletions(-)
>>>   create mode 100644
>>> Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt

>>> diff --git
>>> a/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
>>> b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
>>> new file mode 100644
>>> index 0000000..5351a30
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
>>> @@ -0,0 +1,36 @@
>>> +Renesas RCar gen2 USB PHY bindings
>>> +----------------------------------
>>> +
>>> +Bindings for the USB PHY block used in some Renesas SoCs.
>>> +
>>> +Required properties:
>>> + - compatible:  "renesas,usb-phy-r8a7790" for the R8A7790 SoC
>>> +        "renesas,usb-phy-r8a7791" for the R8A7791 SoC
>>> + - reg : A single region to access device registers
>>> + - clocks : The reference to the clock to use for this block
>>> + - clock-names : The name for the clock at index 0 (must be "usbhs")
>>> +
>>> +Optional properties:
>>> +
>>> + - renesas,usb0-device: boolean, if present USB0 is connected to HS
>>> device
>>> +            otherwise the USB0 is connected to OHCI/EHCI host.

>>     IIUC, the testing has shown that USBHS is dual-role controller in
>> that case, i.e. supports both host and device roles (the manual has the
>> host controller details too). Vladimir, is it so?

> Currently there is no auto-detection for this, so it gets set at
> start time.

    The mode can be auto-detected by reading SW5. My point was however, that 
it doesn't seem correct to call the prop "renesas,usb0-device". I'd rather 
suggest "renesas,usb0-usbhs" if you keep sticking to the scheme opposite to 
the platform data.

WBR, Sergei

Re: [PATCH 3/9] phy-rcar-usb-gen2: add device tree support

[Sergei Shtylyov]

Hello.

On 03/06/2014 09:19 PM, Ben Dooks wrote:

>>> Add support for the phy-rcar-gen2-usb driver to be probed from device
>>> tree.

>>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>>> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
[...]

>>>   drivers/usb/phy/phy-rcar-gen2-usb.c                | 34
>>> +++++++++++++++++---
>>>   3 files changed, 66 insertions(+), 5 deletions(-)
>>>   create mode 100644
>>> Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt

>>> diff --git
>>> a/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
>>> b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
>>> new file mode 100644
>>> index 0000000..5351a30
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/usb/renesas,rcar-gen2-usb-phy.txt
>>> @@ -0,0 +1,36 @@
>>> +Renesas RCar gen2 USB PHY bindings
>>> +----------------------------------
>>> +
>>> +Bindings for the USB PHY block used in some Renesas SoCs.
>>> +
>>> +Required properties:
>>> + - compatible:  "renesas,usb-phy-r8a7790" for the R8A7790 SoC
>>> +        "renesas,usb-phy-r8a7791" for the R8A7791 SoC
>>> + - reg : A single region to access device registers
>>> + - clocks : The reference to the clock to use for this block
>>> + - clock-names : The name for the clock at index 0 (must be "usbhs")
>>> +
>>> +Optional properties:
>>> +
>>> + - renesas,usb0-device: boolean, if present USB0 is connected to HS
>>> device
>>> +            otherwise the USB0 is connected to OHCI/EHCI host.

>>     IIUC, the testing has shown that USBHS is dual-role controller in
>> that case, i.e. supports both host and device roles (the manual has the
>> host controller details too). Vladimir, is it so?

> Currently there is no auto-detection for this, so it gets set at
> start time.

    The mode can be auto-detected by reading SW5. My point was however, that 
it doesn't seem correct to call the prop "renesas,usb0-device". I'd rather 
suggest "renesas,usb0-usbhs" if you keep sticking to the scheme opposite to 
the platform data.

WBR, Sergei

[PATCH 5/9] ARM: shmbobile: r8a7790.dtsi: add pci0/1/2 nodes

[Ben Dooks]

Add nodes for USB PCI bridge devices.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Cc: devicetree@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: horms+renesas@verge.net.au

Conflicts:
	arch/arm/boot/dts/r8a7790.dtsi
---
 arch/arm/boot/dts/r8a7790.dtsi | 39 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 39 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index a1e7c39..7325fee 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -763,4 +763,43 @@
 		#size-cells = <0>;
 		status = "disabled";
 	};
+
+	pci0: pci@ee090000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee090000 0x0 0xc00>,
+		      <0x0 0xee080000 0x0 0x1100>;
+		interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+
+		bus-range = <0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+	};
+
+	pci1: pci@ee0b0000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee0b0000 0x0 0xc00>,
+		      <0x0 0xee0a0000 0x0 0x1100>;
+		interrupts = <0 112 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+
+		bus-range = <1 1>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+	};
+
+	pci2: pci@ee0d0000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee0d0000 0x0 0xc00>,
+		      <0x0 0xee0c0000 0x0 0x1100>;
+		interrupts = <0 113 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+
+		bus-range = <2 2>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+	};
 };
-- 
1.9.0

[PATCH 5/9] ARM: shmbobile: r8a7790.dtsi: add pci0/1/2 nodes

[Ben Dooks]

Add nodes for USB PCI bridge devices.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Cc: devicetree@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: horms+renesas@verge.net.au

Conflicts:
	arch/arm/boot/dts/r8a7790.dtsi
---
 arch/arm/boot/dts/r8a7790.dtsi | 39 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 39 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index a1e7c39..7325fee 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -763,4 +763,43 @@
 		#size-cells = <0>;
 		status = "disabled";
 	};
+
+	pci0: pci@ee090000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee090000 0x0 0xc00>,
+		      <0x0 0xee080000 0x0 0x1100>;
+		interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+
+		bus-range = <0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+	};
+
+	pci1: pci@ee0b0000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee0b0000 0x0 0xc00>,
+		      <0x0 0xee0a0000 0x0 0x1100>;
+		interrupts = <0 112 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+
+		bus-range = <1 1>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+	};
+
+	pci2: pci@ee0d0000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee0d0000 0x0 0xc00>,
+		      <0x0 0xee0c0000 0x0 0x1100>;
+		interrupts = <0 113 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+
+		bus-range = <2 2>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+	};
 };
-- 
1.9.0

Re: [PATCH 5/9] ARM: shmbobile: r8a7790.dtsi: add pci0/1/2 nodes

[Sergei Shtylyov]

On 03/06/2014 09:01 PM, Ben Dooks wrote:

    s/shmbobile/shmobile/ in the subject.

> Add nodes for USB PCI bridge devices.

> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>

WBR, Sergei

Re: [PATCH 5/9] ARM: shmbobile: r8a7790.dtsi: add pci0/1/2 nodes

[Sergei Shtylyov]

On 03/06/2014 09:01 PM, Ben Dooks wrote:

    s/shmbobile/shmobile/ in the subject.

> Add nodes for USB PCI bridge devices.

> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>

WBR, Sergei

[PATCH 6/9] ARM: shmobile: lager.dts: add pci 0/1/2

[Ben Dooks]

Enable pci1 and pci2 nodes for USB controllers attached to the AHB<>PCI
bridge devices. Node pci0 is added for the moment, but not enabled as it
could be switched to usb-gadget mode later.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Cc: linux-sh@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Simon Horman <horms@verge.net.au>
---
 arch/arm/boot/dts/r8a7790-lager.dts | 32 ++++++++++++++++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 26a9010..fd6851f 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -148,6 +148,21 @@
 		renesas,groups = "qspi_ctrl", "qspi_data4";
 		renesas,function = "qspi";
 	};
+
+	usb0_pins: usb0 {
+		renesas,groups = "usb0";
+		renesas,function = "usb0";
+	};
+
+	usb1_pins: usb1 {
+		renesas,groups = "usb1";
+		renesas,function = "usb1";
+	};
+
+	usb2_pins: usb2 {
+		renesas,groups = "usb2";
+		renesas,function = "usb2";
+	};
 };
 
 &mmcif1 {
@@ -214,3 +229,20 @@
 	cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
+
+&pci0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+};
+
+&pci1 {
+	status = "okay";
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+};
+
+&pci2 {
+	status = "okay";
+	pinctrl-0 = <&usb2_pins>;
+	pinctrl-names = "default";
+};
-- 
1.9.0

[PATCH 6/9] ARM: shmobile: lager.dts: add pci 0/1/2

[Ben Dooks]

Enable pci1 and pci2 nodes for USB controllers attached to the AHB<>PCI
bridge devices. Node pci0 is added for the moment, but not enabled as it
could be switched to usb-gadget mode later.

Signed-off-by: Ben Dooks <ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>
Reviewed-by: Ian Molton <ian.molton-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>
---
Cc: linux-sh-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: Magnus Damm <magnus.damm-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Cc: Simon Horman <horms-/R6kz+dDXgpPR4JQBCEnsQ@public.gmane.org>
---
 arch/arm/boot/dts/r8a7790-lager.dts | 32 ++++++++++++++++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 26a9010..fd6851f 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -148,6 +148,21 @@
 		renesas,groups = "qspi_ctrl", "qspi_data4";
 		renesas,function = "qspi";
 	};
+
+	usb0_pins: usb0 {
+		renesas,groups = "usb0";
+		renesas,function = "usb0";
+	};
+
+	usb1_pins: usb1 {
+		renesas,groups = "usb1";
+		renesas,function = "usb1";
+	};
+
+	usb2_pins: usb2 {
+		renesas,groups = "usb2";
+		renesas,function = "usb2";
+	};
 };
 
 &mmcif1 {
@@ -214,3 +229,20 @@
 	cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
+
+&pci0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+};
+
+&pci1 {
+	status = "okay";
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+};
+
+&pci2 {
+	status = "okay";
+	pinctrl-0 = <&usb2_pins>;
+	pinctrl-names = "default";
+};
-- 
1.9.0

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 7/9] ARM: shmobile: r8a7790.dtsi: add usbphy node

[Ben Dooks]

Add node for USB PHY driver to the base R8A7790 device tree include file.
It is up to the board file to enable and configure it as necessary.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Cc: devicetree@vger.kernel.org
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: linux-sh@vger.kernel.org
---
 arch/arm/boot/dts/r8a7790.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 7325fee..4c03c46 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -802,4 +802,12 @@
 		#address-cells = <3>;
 		#size-cells = <2>;
 	};
+
+	usbphy: usbphy@e6590100 {
+		compatible = "renesas,usb-phy-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
+		clock-names = "usbhs";
+		reg = < 0x0 0xe6590100 0x0 0x100>;
+		status = "disabled";
+	};
 };
-- 
1.9.0

[PATCH 7/9] ARM: shmobile: r8a7790.dtsi: add usbphy node

[Ben Dooks]

Add node for USB PHY driver to the base R8A7790 device tree include file.
It is up to the board file to enable and configure it as necessary.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Cc: devicetree@vger.kernel.org
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: linux-sh@vger.kernel.org
---
 arch/arm/boot/dts/r8a7790.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 7325fee..4c03c46 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -802,4 +802,12 @@
 		#address-cells = <3>;
 		#size-cells = <2>;
 	};
+
+	usbphy: usbphy@e6590100 {
+		compatible = "renesas,usb-phy-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
+		clock-names = "usbhs";
+		reg = < 0x0 0xe6590100 0x0 0x100>;
+		status = "disabled";
+	};
 };
-- 
1.9.0

[PATCH 8/9] ARM: shmobile: lager.dts: add usbphy reference

[Ben Dooks]

Enable the usbphy node so that the phy driver is available.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Cc: linux-sh@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Simon Horman <horms@verge.net.au>
---
 arch/arm/boot/dts/r8a7790-lager.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index fd6851f..63d58d6 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -246,3 +246,7 @@
 	pinctrl-0 = <&usb2_pins>;
 	pinctrl-names = "default";
 };
+
+&usbphy {
+	status = "okay";
+};
-- 
1.9.0

[PATCH 8/9] ARM: shmobile: lager.dts: add usbphy reference

[Ben Dooks]

Enable the usbphy node so that the phy driver is available.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
---
Cc: linux-sh@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Simon Horman <horms@verge.net.au>
---
 arch/arm/boot/dts/r8a7790-lager.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index fd6851f..63d58d6 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -246,3 +246,7 @@
 	pinctrl-0 = <&usb2_pins>;
 	pinctrl-names = "default";
 };
+
+&usbphy {
+	status = "okay";
+};
-- 
1.9.0

Re: [PATCH 8/9] ARM: shmobile: lager.dts: add usbphy reference

[Sergei Shtylyov]

Hello.

On 03/06/2014 09:01 PM, Ben Dooks wrote:

> Enable the usbphy node so that the phy driver is available.

> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
> ---
> Cc: linux-sh@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> Cc: Magnus Damm <magnus.damm@gmail.com>
> Cc: Simon Horman <horms@verge.net.au>
> ---
>   arch/arm/boot/dts/r8a7790-lager.dts | 4 ++++
>   1 file changed, 4 insertions(+)

> diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
> index fd6851f..63d58d6 100644
> --- a/arch/arm/boot/dts/r8a7790-lager.dts
> +++ b/arch/arm/boot/dts/r8a7790-lager.dts
> @@ -246,3 +246,7 @@
>   	pinctrl-0 = <&usb2_pins>;
>   	pinctrl-names = "default";
>   };
> +
> +&usbphy {
> +	status = "okay";
> +};

    I don't see why we need this patch. Why not make USB PHY always enabled?

WBR, Sergei

Re: [PATCH 8/9] ARM: shmobile: lager.dts: add usbphy reference

[Sergei Shtylyov]

Hello.

On 03/06/2014 09:01 PM, Ben Dooks wrote:

> Enable the usbphy node so that the phy driver is available.

> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
> ---
> Cc: linux-sh@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> Cc: Magnus Damm <magnus.damm@gmail.com>
> Cc: Simon Horman <horms@verge.net.au>
> ---
>   arch/arm/boot/dts/r8a7790-lager.dts | 4 ++++
>   1 file changed, 4 insertions(+)

> diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
> index fd6851f..63d58d6 100644
> --- a/arch/arm/boot/dts/r8a7790-lager.dts
> +++ b/arch/arm/boot/dts/r8a7790-lager.dts
> @@ -246,3 +246,7 @@
>   	pinctrl-0 = <&usb2_pins>;
>   	pinctrl-names = "default";
>   };
> +
> +&usbphy {
> +	status = "okay";
> +};

    I don't see why we need this patch. Why not make USB PHY always enabled?

WBR, Sergei

Re: [PATCH 8/9] ARM: shmobile: lager.dts: add usbphy reference

[Ben Dooks]

On 30/03/14 20:28, Sergei Shtylyov wrote:
> Hello.
>
> On 03/06/2014 09:01 PM, Ben Dooks wrote:
>
>> Enable the usbphy node so that the phy driver is available.
>
>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>> Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
>> ---
>> Cc: linux-sh@vger.kernel.org
>> Cc: devicetree@vger.kernel.org
>> Cc: Magnus Damm <magnus.damm@gmail.com>
>> Cc: Simon Horman <horms@verge.net.au>
>> ---
>>   arch/arm/boot/dts/r8a7790-lager.dts | 4 ++++
>>   1 file changed, 4 insertions(+)
>
>> diff --git a/arch/arm/boot/dts/r8a7790-lager.dts
>> b/arch/arm/boot/dts/r8a7790-lager.dts
>> index fd6851f..63d58d6 100644
>> --- a/arch/arm/boot/dts/r8a7790-lager.dts
>> +++ b/arch/arm/boot/dts/r8a7790-lager.dts
>> @@ -246,3 +246,7 @@
>>       pinctrl-0 = <&usb2_pins>;
>>       pinctrl-names = "default";
>>   };
>> +
>> +&usbphy {
>> +    status = "okay";
>> +};
>
>     I don't see why we need this patch. Why not make USB PHY always
> enabled?

I have a current setup where we do not want the kernel to try
and probe the phy device.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

Re: [PATCH 8/9] ARM: shmobile: lager.dts: add usbphy reference

[Ben Dooks]

On 30/03/14 20:28, Sergei Shtylyov wrote:
> Hello.
>
> On 03/06/2014 09:01 PM, Ben Dooks wrote:
>
>> Enable the usbphy node so that the phy driver is available.
>
>> Signed-off-by: Ben Dooks <ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>
>> Reviewed-by: Ian Molton <ian.molton-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>
>> ---
>> Cc: linux-sh-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>> Cc: Magnus Damm <magnus.damm-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> Cc: Simon Horman <horms-/R6kz+dDXgpPR4JQBCEnsQ@public.gmane.org>
>> ---
>>   arch/arm/boot/dts/r8a7790-lager.dts | 4 ++++
>>   1 file changed, 4 insertions(+)
>
>> diff --git a/arch/arm/boot/dts/r8a7790-lager.dts
>> b/arch/arm/boot/dts/r8a7790-lager.dts
>> index fd6851f..63d58d6 100644
>> --- a/arch/arm/boot/dts/r8a7790-lager.dts
>> +++ b/arch/arm/boot/dts/r8a7790-lager.dts
>> @@ -246,3 +246,7 @@
>>       pinctrl-0 = <&usb2_pins>;
>>       pinctrl-names = "default";
>>   };
>> +
>> +&usbphy {
>> +    status = "okay";
>> +};
>
>     I don't see why we need this patch. Why not make USB PHY always
> enabled?

I have a current setup where we do not want the kernel to try
and probe the phy device.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: Renesas RCar device-tree USB series

[Magnus Damm]

Hi Ben,

On Fri, Mar 7, 2014 at 3:01 AM, Ben Dooks <ben.dooks@codethink.co.uk> wrote:
> This is a new series covering enabling the RCar series of SoCs USB
> with device-tree based booting. It has been tested on the R8A7790
> Lager board.
>
> Improvements from the previous series include:
>
>         - mapping usb to the relevant phy by dt
>         - better use of existing pci of functions
>
> Note, there is still an issue with the second gigabyte of memory on
> the Lager, which with current kernels causes the system to abort on
> startup. This series will only work if the top memory area is disabled.

Thanks for these patches. I think they start looking really good.

In my mind there are two outstanding issues:

1) Is the USB core code change acceptable or not?

The patch "[PATCH 4/9] usb: phy: check for of_node when getting phy"
looks quite fine to me, but I wonder if the USB maintainers will
accept it as-is or require some rework. I would say that the rest of
this series depends on that USB core change.

2) Per-port USB PHY driver configuration via DT

Right now each USB host controller points to the same PHY device.
Thanks for working on describing the topology! As you know, the PHY
driver itself handles several USB ports, and I'd like to use DT to
represent the mapping between which PHY port that maps to what USB
Host controller to allow proper run time configuration. Right now in
this version of the series there is no such mapping. Of course, that
depends on proper USB PHY DT bindings...

Thanks,

/ magnus

Re: Renesas RCar device-tree USB series

[Ben Dooks]

On 07/03/14 05:36, Magnus Damm wrote:
> Hi Ben,
>
> On Fri, Mar 7, 2014 at 3:01 AM, Ben Dooks <ben.dooks@codethink.co.uk> wrote:
>> This is a new series covering enabling the RCar series of SoCs USB
>> with device-tree based booting. It has been tested on the R8A7790
>> Lager board.
>>
>> Improvements from the previous series include:
>>
>>          - mapping usb to the relevant phy by dt
>>          - better use of existing pci of functions
>>
>> Note, there is still an issue with the second gigabyte of memory on
>> the Lager, which with current kernels causes the system to abort on
>> startup. This series will only work if the top memory area is disabled.
>
> Thanks for these patches. I think they start looking really good.
>
> In my mind there are two outstanding issues:
>
> 1) Is the USB core code change acceptable or not?
>
> The patch "[PATCH 4/9] usb: phy: check for of_node when getting phy"
> looks quite fine to me, but I wonder if the USB maintainers will
> accept it as-is or require some rework. I would say that the rest of
> this series depends on that USB core change.

I'm not sure, but without it we need to hack the PHY driver to
turn on the PHY at start time.

> 2) Per-port USB PHY driver configuration via DT
>
> Right now each USB host controller points to the same PHY device.
> Thanks for working on describing the topology! As you know, the PHY
> driver itself handles several USB ports, and I'd like to use DT to
> represent the mapping between which PHY port that maps to what USB
> Host controller to allow proper run time configuration. Right now in
> this version of the series there is no such mapping. Of course, that
> depends on proper USB PHY DT bindings...

Hmm, given the shared phy is shared and referenced counted then
I don't /think/ there is much more to be done for this. If we add
more PHYs then I would assume that each one of them would



-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

Re: Renesas RCar device-tree USB series

[Sergei Shtylyov]

Hello.

On 03/07/2014 05:30 PM, Ben Dooks wrote:

>>> This is a new series covering enabling the RCar series of SoCs USB
>>> with device-tree based booting. It has been tested on the R8A7790
>>> Lager board.

>>> Improvements from the previous series include:

>>>          - mapping usb to the relevant phy by dt
>>>          - better use of existing pci of functions

>>> Note, there is still an issue with the second gigabyte of memory on
>>> the Lager, which with current kernels causes the system to abort on
>>> startup. This series will only work if the top memory area is disabled.

>> Thanks for these patches. I think they start looking really good.

>> In my mind there are two outstanding issues:

[...]

>> 2) Per-port USB PHY driver configuration via DT
>> Right now each USB host controller points to the same PHY device.
>> Thanks for working on describing the topology! As you know, the PHY
>> driver itself handles several USB ports, and I'd like to use DT to
>> represent the mapping between which PHY port that maps to what USB
>> Host controller to allow proper run time configuration. Right now in
>> this version of the series there is no such mapping. Of course, that
>> depends on proper USB PHY DT bindings...

> Hmm, given the shared phy is shared and referenced counted then
> I don't /think/ there is much more to be done for this. If we add
> more PHYs then I would assume that each one of them would

    It seems you didn't finish the sentence...

WBR, Sergei

Re: Renesas RCar device-tree USB series

[Ben Dooks]

On 07/03/14 17:30, Sergei Shtylyov wrote:
> Hello.
>
> On 03/07/2014 05:30 PM, Ben Dooks wrote:
>
>>>> This is a new series covering enabling the RCar series of SoCs USB
>>>> with device-tree based booting. It has been tested on the R8A7790
>>>> Lager board.
>
>>>> Improvements from the previous series include:
>
>>>>          - mapping usb to the relevant phy by dt
>>>>          - better use of existing pci of functions
>
>>>> Note, there is still an issue with the second gigabyte of memory on
>>>> the Lager, which with current kernels causes the system to abort on
>>>> startup. This series will only work if the top memory area is disabled.
>
>>> Thanks for these patches. I think they start looking really good.
>
>>> In my mind there are two outstanding issues:
>
> [...]
>
>>> 2) Per-port USB PHY driver configuration via DT
>>> Right now each USB host controller points to the same PHY device.
>>> Thanks for working on describing the topology! As you know, the PHY
>>> driver itself handles several USB ports, and I'd like to use DT to
>>> represent the mapping between which PHY port that maps to what USB
>>> Host controller to allow proper run time configuration. Right now in
>>> this version of the series there is no such mapping. Of course, that
>>> depends on proper USB PHY DT bindings...
>
>> Hmm, given the shared phy is shared and referenced counted then
>> I don't /think/ there is much more to be done for this. If we add
>> more PHYs then I would assume that each one of them would
>
>     It seems you didn't finish the sentence...

I deleted the last bit by accident.

"have their own phy driver instance"

>
> WBR, Sergei
>


-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius