From: Igor Grinberg <grinberg@compulab.co.il>
To: Tony Lindgren <tony@atomide.com>, Stefan Roese <sr@denx.de>
Cc: linux-arm-kernel@lists.infradead.org, linux-omap@vger.kernel.org,
Dmitry Lifshitz <lifshitz@compulab.co.il>
Subject: Re: [PATCH] arm: omap: cm-t3530: Add MMC2/SDIO/WLAN support
Date: Thu, 13 Mar 2014 11:13:53 +0200 [thread overview]
Message-ID: <532176D1.2070000@compulab.co.il> (raw)
In-Reply-To: <20140312174423.GC1996@atomide.com>
On 03/12/14 19:44, Tony Lindgren wrote:
> * Stefan Roese <sr@denx.de> [140312 03:52]:
>> Add support for the MMC2/SDIO WiFi Libertas (Marvell) module available
>> on the CM-T3530 SOM.
>>
>> Signed-off-by: Stefan Roese <sr@denx.de>
>> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
>> Cc: Igor Grinberg <grinberg@compulab.co.il>
>> Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
>> ---
>> This patch is based on current mainline (v3.14-rc6) plus this compulab patch
>> series from Dmitry:
>>
>> [PATCH 00/11] ARM: dts: sbc-t3x: add support for more boards
>> http://www.spinics.net/lists/arm-kernel/msg300078.html
>
> Thanks applying into omap-for-v3.15/dt, no guarantees it gets merged though
> as it's getting so close to the merge window.
>
> Regards,
>
> Tony
>
>> arch/arm/boot/dts/omap3-cm-t3530.dts | 36 ++++++++++++++++++++++++++++++++++++
>> 1 file changed, 36 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/omap3-cm-t3530.dts b/arch/arm/boot/dts/omap3-cm-t3530.dts
>> index 9faf1cd..d145849 100644
>> --- a/arch/arm/boot/dts/omap3-cm-t3530.dts
>> +++ b/arch/arm/boot/dts/omap3-cm-t3530.dts
>> @@ -9,4 +9,40 @@
>> / {
>> model = "CompuLab CM-T3530";
>> compatible = "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
>> +
>> + /* Regulator to trigger the reset signal of the Wifi module */
>> + mmc2_sdio_reset: regulator-mmc2-sdio-reset {
>> + compatible = "regulator-fixed";
>> + regulator-name = "regulator-mmc2-sdio-reset";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + gpio = <&twl_gpio 2 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> + };
>> +};
>> +
>> +&omap3_pmx_core {
>> + mmc2_pins: pinmux_mmc2_pins {
>> + pinctrl-single,pins = <
>> + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
>> + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
>> + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
>> + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
>> + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
>> + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
>> + OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dir_dat0 */
>> + OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dir_dat1 */
>> + OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dir_cmd */
>> + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */
>> + >;
>> + };
>> +};
>> +
>> +&mmc2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc2_pins>;
>> + vmmc-supply = <&mmc2_sdio_reset>;
>> + non-removable;
>> + bus-width = <4>;
>> + cap-power-off-card;
>> };
>> --
>> 1.8.5.5
>>
>
--
Regards,
Igor.
WARNING: multiple messages have this Message-ID (diff)
From: grinberg@compulab.co.il (Igor Grinberg)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] arm: omap: cm-t3530: Add MMC2/SDIO/WLAN support
Date: Thu, 13 Mar 2014 11:13:53 +0200 [thread overview]
Message-ID: <532176D1.2070000@compulab.co.il> (raw)
In-Reply-To: <20140312174423.GC1996@atomide.com>
On 03/12/14 19:44, Tony Lindgren wrote:
> * Stefan Roese <sr@denx.de> [140312 03:52]:
>> Add support for the MMC2/SDIO WiFi Libertas (Marvell) module available
>> on the CM-T3530 SOM.
>>
>> Signed-off-by: Stefan Roese <sr@denx.de>
>> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
>> Cc: Igor Grinberg <grinberg@compulab.co.il>
>> Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
>> ---
>> This patch is based on current mainline (v3.14-rc6) plus this compulab patch
>> series from Dmitry:
>>
>> [PATCH 00/11] ARM: dts: sbc-t3x: add support for more boards
>> http://www.spinics.net/lists/arm-kernel/msg300078.html
>
> Thanks applying into omap-for-v3.15/dt, no guarantees it gets merged though
> as it's getting so close to the merge window.
>
> Regards,
>
> Tony
>
>> arch/arm/boot/dts/omap3-cm-t3530.dts | 36 ++++++++++++++++++++++++++++++++++++
>> 1 file changed, 36 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/omap3-cm-t3530.dts b/arch/arm/boot/dts/omap3-cm-t3530.dts
>> index 9faf1cd..d145849 100644
>> --- a/arch/arm/boot/dts/omap3-cm-t3530.dts
>> +++ b/arch/arm/boot/dts/omap3-cm-t3530.dts
>> @@ -9,4 +9,40 @@
>> / {
>> model = "CompuLab CM-T3530";
>> compatible = "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
>> +
>> + /* Regulator to trigger the reset signal of the Wifi module */
>> + mmc2_sdio_reset: regulator-mmc2-sdio-reset {
>> + compatible = "regulator-fixed";
>> + regulator-name = "regulator-mmc2-sdio-reset";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + gpio = <&twl_gpio 2 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> + };
>> +};
>> +
>> +&omap3_pmx_core {
>> + mmc2_pins: pinmux_mmc2_pins {
>> + pinctrl-single,pins = <
>> + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
>> + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
>> + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
>> + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
>> + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
>> + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
>> + OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dir_dat0 */
>> + OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dir_dat1 */
>> + OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dir_cmd */
>> + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */
>> + >;
>> + };
>> +};
>> +
>> +&mmc2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc2_pins>;
>> + vmmc-supply = <&mmc2_sdio_reset>;
>> + non-removable;
>> + bus-width = <4>;
>> + cap-power-off-card;
>> };
>> --
>> 1.8.5.5
>>
>
--
Regards,
Igor.
next prev parent reply other threads:[~2014-03-13 9:14 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-03-12 10:49 [PATCH] arm: omap: cm-t3530: Add MMC2/SDIO/WLAN support Stefan Roese
2014-03-12 10:49 ` Stefan Roese
2014-03-12 17:44 ` Tony Lindgren
2014-03-12 17:44 ` Tony Lindgren
2014-03-13 9:13 ` Igor Grinberg [this message]
2014-03-13 9:13 ` Igor Grinberg
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=532176D1.2070000@compulab.co.il \
--to=grinberg@compulab.co.il \
--cc=lifshitz@compulab.co.il \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
--cc=sr@denx.de \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.