* Enabling uart 3 in arndale @ 2014-03-14 8:04 ` armdev 0 siblings, 0 replies; 20+ messages in thread From: armdev @ 2014-03-14 8:04 UTC (permalink / raw) To: Tushar Behera; +Cc: linux-samsung-soc, u-boot Hi, We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as XuRXD3 : UART_3_RXD/GPA1[4] : 2 XuTXD3 : UART_3_TXD/GPA1[5] : 4 As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. Can you please suggest what is the right procedure -Regards armdev team @FTM ^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] Enabling uart 3 in arndale @ 2014-03-14 8:04 ` armdev 0 siblings, 0 replies; 20+ messages in thread From: armdev @ 2014-03-14 8:04 UTC (permalink / raw) To: u-boot Hi, We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as XuRXD3 : UART_3_RXD/GPA1[4] : 2 XuTXD3 : UART_3_TXD/GPA1[5] : 4 As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. Can you please suggest what is the right procedure -Regards armdev team @FTM ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Enabling uart 3 in arndale 2014-03-14 8:04 ` [U-Boot] " armdev @ 2014-03-16 9:22 ` armdev -1 siblings, 0 replies; 20+ messages in thread From: armdev @ 2014-03-16 9:22 UTC (permalink / raw) To: Tushar Behera, linux-samsung-soc, u-boot Please can someone help On 14-Mar-2014, at 1:34 pm, armdev <armdev.ftm@gmail.com> wrote: > Hi, > > We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as > > XuRXD3 : UART_3_RXD/GPA1[4] : 2 > XuTXD3 : UART_3_TXD/GPA1[5] : 4 > > As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) > Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. > > Can you please suggest what is the right procedure > > -Regards > armdev team @FTM ^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] Enabling uart 3 in arndale @ 2014-03-16 9:22 ` armdev 0 siblings, 0 replies; 20+ messages in thread From: armdev @ 2014-03-16 9:22 UTC (permalink / raw) To: u-boot Please can someone help On 14-Mar-2014, at 1:34 pm, armdev <armdev.ftm@gmail.com> wrote: > Hi, > > We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as > > XuRXD3 : UART_3_RXD/GPA1[4] : 2 > XuTXD3 : UART_3_TXD/GPA1[5] : 4 > > As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) > Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. > > Can you please suggest what is the right procedure > > -Regards > armdev team @FTM ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [U-Boot] Enabling uart 3 in arndale 2014-03-14 8:04 ` [U-Boot] " armdev @ 2014-03-16 9:26 ` Michael Trimarchi -1 siblings, 0 replies; 20+ messages in thread From: Michael Trimarchi @ 2014-03-16 9:26 UTC (permalink / raw) To: armdev; +Cc: Tushar Behera, u-boot@lists.denx.de, linux-samsung-soc Hi On Fri, Mar 14, 2014 at 9:04 AM, armdev <armdev.ftm@gmail.com> wrote: > Hi, > > We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as > > XuRXD3 : UART_3_RXD/GPA1[4] : 2 > XuTXD3 : UART_3_TXD/GPA1[5] : 4 > > As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) > Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. > > Can you please suggest what is the right procedure > Did you change the board console output ;)? Michael > -Regards > armdev team @FTM > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot -- | Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com | ^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] Enabling uart 3 in arndale @ 2014-03-16 9:26 ` Michael Trimarchi 0 siblings, 0 replies; 20+ messages in thread From: Michael Trimarchi @ 2014-03-16 9:26 UTC (permalink / raw) To: u-boot Hi On Fri, Mar 14, 2014 at 9:04 AM, armdev <armdev.ftm@gmail.com> wrote: > Hi, > > We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as > > XuRXD3 : UART_3_RXD/GPA1[4] : 2 > XuTXD3 : UART_3_TXD/GPA1[5] : 4 > > As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) > Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. > > Can you please suggest what is the right procedure > Did you change the board console output ;)? Michael > -Regards > armdev team @FTM > _______________________________________________ > U-Boot mailing list > U-Boot at lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot -- | Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com | ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [U-Boot] Enabling uart 3 in arndale 2014-03-16 9:26 ` Michael Trimarchi @ 2014-03-16 10:07 ` armdev -1 siblings, 0 replies; 20+ messages in thread From: armdev @ 2014-03-16 10:07 UTC (permalink / raw) To: Michael Trimarchi; +Cc: Tushar Behera, u-boot@lists.denx.de, linux-samsung-soc Dear Michael, Yep didn’t got any prints. So tried a hack. a) Booted using uart 2 b) set the GPACON c) Copied the config from 0x12c20000 to 0x12c30000 d)tried to write a char 0x41 (A) on 0x12c20020 0x12c30020, I got output on UART2 but not on UART3. We would like to use both uarts. Have you used UART3, did the boot to UART3 worked for you ? So you see any problem with any of our steps listed in this / pref mail. Thanks armdev team On 16-Mar-2014, at 2:56 pm, Michael Trimarchi <michael@amarulasolutions.com> wrote: > Hi > > On Fri, Mar 14, 2014 at 9:04 AM, armdev <armdev.ftm@gmail.com> wrote: >> Hi, >> >> We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as >> >> XuRXD3 : UART_3_RXD/GPA1[4] : 2 >> XuTXD3 : UART_3_TXD/GPA1[5] : 4 >> >> As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) >> Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. >> >> Can you please suggest what is the right procedure >> > > Did you change the board console output ;)? > > Michael > >> -Regards >> armdev team @FTM >> _______________________________________________ >> U-Boot mailing list >> U-Boot@lists.denx.de >> http://lists.denx.de/mailman/listinfo/u-boot > > > > -- > | Michael Nazzareno Trimarchi Amarula Solutions BV | > | COO - Founder Cruquiuskade 47 | > | +31(0)851119172 Amsterdam 1018 AM NL | > | [`as] http://www.amarulasolutions.com | ^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] Enabling uart 3 in arndale @ 2014-03-16 10:07 ` armdev 0 siblings, 0 replies; 20+ messages in thread From: armdev @ 2014-03-16 10:07 UTC (permalink / raw) To: u-boot Dear Michael, Yep didn?t got any prints. So tried a hack. a) Booted using uart 2 b) set the GPACON c) Copied the config from 0x12c20000 to 0x12c30000 d)tried to write a char 0x41 (A) on 0x12c20020 0x12c30020, I got output on UART2 but not on UART3. We would like to use both uarts. Have you used UART3, did the boot to UART3 worked for you ? So you see any problem with any of our steps listed in this / pref mail. Thanks armdev team On 16-Mar-2014, at 2:56 pm, Michael Trimarchi <michael@amarulasolutions.com> wrote: > Hi > > On Fri, Mar 14, 2014 at 9:04 AM, armdev <armdev.ftm@gmail.com> wrote: >> Hi, >> >> We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as >> >> XuRXD3 : UART_3_RXD/GPA1[4] : 2 >> XuTXD3 : UART_3_TXD/GPA1[5] : 4 >> >> As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) >> Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. >> >> Can you please suggest what is the right procedure >> > > Did you change the board console output ;)? > > Michael > >> -Regards >> armdev team @FTM >> _______________________________________________ >> U-Boot mailing list >> U-Boot at lists.denx.de >> http://lists.denx.de/mailman/listinfo/u-boot > > > > -- > | Michael Nazzareno Trimarchi Amarula Solutions BV | > | COO - Founder Cruquiuskade 47 | > | +31(0)851119172 Amsterdam 1018 AM NL | > | [`as] http://www.amarulasolutions.com | ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [U-Boot] Enabling uart 3 in arndale 2014-03-16 10:07 ` armdev @ 2014-03-16 10:25 ` Michael Trimarchi -1 siblings, 0 replies; 20+ messages in thread From: Michael Trimarchi @ 2014-03-16 10:25 UTC (permalink / raw) To: armdev; +Cc: Tushar Behera, u-boot@lists.denx.de, linux-samsung-soc Hi On Sun, Mar 16, 2014 at 11:07 AM, armdev <armdev.ftm@gmail.com> wrote: > Dear Michael, > Yep didn't got any prints. So tried a hack. > a) Booted using uart 2 > b) set the GPACON > c) Copied the config from 0x12c20000 to 0x12c30000 > d)tried to write a char 0x41 (A) on 0x12c20020 0x12c30020, I got output on UART2 but not on UART3. > > We would like to use both uarts. > Have you used UART3, did the boot to UART3 worked for you ? So you see any problem with any of our steps listed in this / pref mail. > Are you sure that you don't need to clock uart logic? I don't have such board I'm trying just to help you Michael > Thanks > armdev team > > On 16-Mar-2014, at 2:56 pm, Michael Trimarchi <michael@amarulasolutions.com> wrote: > >> Hi >> >> On Fri, Mar 14, 2014 at 9:04 AM, armdev <armdev.ftm@gmail.com> wrote: >>> Hi, >>> >>> We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as >>> >>> XuRXD3 : UART_3_RXD/GPA1[4] : 2 >>> XuTXD3 : UART_3_TXD/GPA1[5] : 4 >>> >>> As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) >>> Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. >>> >>> Can you please suggest what is the right procedure >>> >> >> Did you change the board console output ;)? >> >> Michael >> >>> -Regards >>> armdev team @FTM >>> _______________________________________________ >>> U-Boot mailing list >>> U-Boot@lists.denx.de >>> http://lists.denx.de/mailman/listinfo/u-boot >> >> >> >> -- >> | Michael Nazzareno Trimarchi Amarula Solutions BV | >> | COO - Founder Cruquiuskade 47 | >> | +31(0)851119172 Amsterdam 1018 AM NL | >> | [`as] http://www.amarulasolutions.com | > -- | Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com | ^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] Enabling uart 3 in arndale @ 2014-03-16 10:25 ` Michael Trimarchi 0 siblings, 0 replies; 20+ messages in thread From: Michael Trimarchi @ 2014-03-16 10:25 UTC (permalink / raw) To: u-boot Hi On Sun, Mar 16, 2014 at 11:07 AM, armdev <armdev.ftm@gmail.com> wrote: > Dear Michael, > Yep didn't got any prints. So tried a hack. > a) Booted using uart 2 > b) set the GPACON > c) Copied the config from 0x12c20000 to 0x12c30000 > d)tried to write a char 0x41 (A) on 0x12c20020 0x12c30020, I got output on UART2 but not on UART3. > > We would like to use both uarts. > Have you used UART3, did the boot to UART3 worked for you ? So you see any problem with any of our steps listed in this / pref mail. > Are you sure that you don't need to clock uart logic? I don't have such board I'm trying just to help you Michael > Thanks > armdev team > > On 16-Mar-2014, at 2:56 pm, Michael Trimarchi <michael@amarulasolutions.com> wrote: > >> Hi >> >> On Fri, Mar 14, 2014 at 9:04 AM, armdev <armdev.ftm@gmail.com> wrote: >>> Hi, >>> >>> We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as >>> >>> XuRXD3 : UART_3_RXD/GPA1[4] : 2 >>> XuTXD3 : UART_3_TXD/GPA1[5] : 4 >>> >>> As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) >>> Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. >>> >>> Can you please suggest what is the right procedure >>> >> >> Did you change the board console output ;)? >> >> Michael >> >>> -Regards >>> armdev team @FTM >>> _______________________________________________ >>> U-Boot mailing list >>> U-Boot at lists.denx.de >>> http://lists.denx.de/mailman/listinfo/u-boot >> >> >> >> -- >> | Michael Nazzareno Trimarchi Amarula Solutions BV | >> | COO - Founder Cruquiuskade 47 | >> | +31(0)851119172 Amsterdam 1018 AM NL | >> | [`as] http://www.amarulasolutions.com | > -- | Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com | ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [U-Boot] Enabling uart 3 in arndale 2014-03-16 10:25 ` Michael Trimarchi @ 2014-03-16 10:42 ` armdev -1 siblings, 0 replies; 20+ messages in thread From: armdev @ 2014-03-16 10:42 UTC (permalink / raw) To: Michael Trimarchi; +Cc: Tushar Behera, u-boot@lists.denx.de, linux-samsung-soc Dear Michael, Thanks for taking out time to extend help. As per the RefManual the UART is taking the SCLK_UART Clock and as there are 4 channels (4 UARTS). Following is from the public exynos 5250 manual (http://www.samsung.com/global/business/semiconductor/file/product/Exynos_5_Dual_User_Manaul_Public_REV100-0.pdf) "Four independent channels with asynchronous and serial input/output ports for general purpose (Channel 0 to 3), and One channel in ISP (ISP-UART Channel 0) … • Each UART contains a Baud-rate generator, a Transmitter, a Receiver and a Control Unit. The Baud-rate generator uses SCLK_UART." -Regards Armdev Team On 16-Mar-2014, at 3:55 pm, Michael Trimarchi <michael@amarulasolutions.com> wrote: > Hi > > On Sun, Mar 16, 2014 at 11:07 AM, armdev <armdev.ftm@gmail.com> wrote: >> Dear Michael, >> Yep didn't got any prints. So tried a hack. >> a) Booted using uart 2 >> b) set the GPACON >> c) Copied the config from 0x12c20000 to 0x12c30000 >> d)tried to write a char 0x41 (A) on 0x12c20020 0x12c30020, I got output on UART2 but not on UART3. >> >> We would like to use both uarts. >> Have you used UART3, did the boot to UART3 worked for you ? So you see any problem with any of our steps listed in this / pref mail. >> > > Are you sure that you don't need to clock uart logic? I don't have > such board I'm trying just to help you > > Michael > >> Thanks >> armdev team >> >> On 16-Mar-2014, at 2:56 pm, Michael Trimarchi <michael@amarulasolutions.com> wrote: >> >>> Hi >>> >>> On Fri, Mar 14, 2014 at 9:04 AM, armdev <armdev.ftm@gmail.com> wrote: >>>> Hi, >>>> >>>> We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as >>>> >>>> XuRXD3 : UART_3_RXD/GPA1[4] : 2 >>>> XuTXD3 : UART_3_TXD/GPA1[5] : 4 >>>> >>>> As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) >>>> Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. >>>> >>>> Can you please suggest what is the right procedure >>>> >>> >>> Did you change the board console output ;)? >>> >>> Michael >>> >>>> -Regards >>>> armdev team @FTM >>>> _______________________________________________ >>>> U-Boot mailing list >>>> U-Boot@lists.denx.de >>>> http://lists.denx.de/mailman/listinfo/u-boot >>> >>> >>> >>> -- >>> | Michael Nazzareno Trimarchi Amarula Solutions BV | >>> | COO - Founder Cruquiuskade 47 | >>> | +31(0)851119172 Amsterdam 1018 AM NL | >>> | [`as] http://www.amarulasolutions.com | >> > > > > -- > | Michael Nazzareno Trimarchi Amarula Solutions BV | > | COO - Founder Cruquiuskade 47 | > | +31(0)851119172 Amsterdam 1018 AM NL | > | [`as] http://www.amarulasolutions.com | ^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] Enabling uart 3 in arndale @ 2014-03-16 10:42 ` armdev 0 siblings, 0 replies; 20+ messages in thread From: armdev @ 2014-03-16 10:42 UTC (permalink / raw) To: u-boot Dear Michael, Thanks for taking out time to extend help. As per the RefManual the UART is taking the SCLK_UART Clock and as there are 4 channels (4 UARTS). Following is from the public exynos 5250 manual (http://www.samsung.com/global/business/semiconductor/file/product/Exynos_5_Dual_User_Manaul_Public_REV100-0.pdf) "Four independent channels with asynchronous and serial input/output ports for general purpose (Channel 0 to 3), and One channel in ISP (ISP-UART Channel 0) ? ? Each UART contains a Baud-rate generator, a Transmitter, a Receiver and a Control Unit. The Baud-rate generator uses SCLK_UART." -Regards Armdev Team On 16-Mar-2014, at 3:55 pm, Michael Trimarchi <michael@amarulasolutions.com> wrote: > Hi > > On Sun, Mar 16, 2014 at 11:07 AM, armdev <armdev.ftm@gmail.com> wrote: >> Dear Michael, >> Yep didn't got any prints. So tried a hack. >> a) Booted using uart 2 >> b) set the GPACON >> c) Copied the config from 0x12c20000 to 0x12c30000 >> d)tried to write a char 0x41 (A) on 0x12c20020 0x12c30020, I got output on UART2 but not on UART3. >> >> We would like to use both uarts. >> Have you used UART3, did the boot to UART3 worked for you ? So you see any problem with any of our steps listed in this / pref mail. >> > > Are you sure that you don't need to clock uart logic? I don't have > such board I'm trying just to help you > > Michael > >> Thanks >> armdev team >> >> On 16-Mar-2014, at 2:56 pm, Michael Trimarchi <michael@amarulasolutions.com> wrote: >> >>> Hi >>> >>> On Fri, Mar 14, 2014 at 9:04 AM, armdev <armdev.ftm@gmail.com> wrote: >>>> Hi, >>>> >>>> We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as >>>> >>>> XuRXD3 : UART_3_RXD/GPA1[4] : 2 >>>> XuTXD3 : UART_3_TXD/GPA1[5] : 4 >>>> >>>> As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) >>>> Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. >>>> >>>> Can you please suggest what is the right procedure >>>> >>> >>> Did you change the board console output ;)? >>> >>> Michael >>> >>>> -Regards >>>> armdev team @FTM >>>> _______________________________________________ >>>> U-Boot mailing list >>>> U-Boot at lists.denx.de >>>> http://lists.denx.de/mailman/listinfo/u-boot >>> >>> >>> >>> -- >>> | Michael Nazzareno Trimarchi Amarula Solutions BV | >>> | COO - Founder Cruquiuskade 47 | >>> | +31(0)851119172 Amsterdam 1018 AM NL | >>> | [`as] http://www.amarulasolutions.com | >> > > > > -- > | Michael Nazzareno Trimarchi Amarula Solutions BV | > | COO - Founder Cruquiuskade 47 | > | +31(0)851119172 Amsterdam 1018 AM NL | > | [`as] http://www.amarulasolutions.com | ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [U-Boot] Enabling uart 3 in arndale 2014-03-16 10:42 ` armdev @ 2014-03-16 12:40 ` Tomasz Figa -1 siblings, 0 replies; 20+ messages in thread From: Tomasz Figa @ 2014-03-16 12:40 UTC (permalink / raw) To: armdev, Michael Trimarchi Cc: Tushar Behera, u-boot@lists.denx.de, linux-samsung-soc Hi, On 16.03.2014 11:42, armdev wrote: > Dear Michael, > Thanks for taking out time to extend help. > > As per the RefManual the UART is taking the SCLK_UART Clock and as there are 4 channels (4 UARTS). > > Following is from the public exynos 5250 manual (http://www.samsung.com/global/business/semiconductor/file/product/Exynos_5_Dual_User_Manaul_Public_REV100-0.pdf) > > "Four independent channels with asynchronous and serial input/output ports for general purpose (Channel 0 to 3), and One channel in ISP (ISP-UART Channel 0) > … > • Each UART contains a Baud-rate generator, a Transmitter, a Receiver and a Control Unit. The Baud-rate generator uses SCLK_UART." Each UART block uses independent clock source, i.e. UART0 uses SCLK_UART0 and UART3 uses SCLK_UART3. Do you have MUX_UART3 and DIV_UART3 configured properly? Do you have the IP bus clock (CLK_UART3) ungated? The public manual contains full description of clock tree and clock controller registers, so you should be able to figure this out. Best regards, Tomasz ^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] Enabling uart 3 in arndale @ 2014-03-16 12:40 ` Tomasz Figa 0 siblings, 0 replies; 20+ messages in thread From: Tomasz Figa @ 2014-03-16 12:40 UTC (permalink / raw) To: u-boot Hi, On 16.03.2014 11:42, armdev wrote: > Dear Michael, > Thanks for taking out time to extend help. > > As per the RefManual the UART is taking the SCLK_UART Clock and as there are 4 channels (4 UARTS). > > Following is from the public exynos 5250 manual (http://www.samsung.com/global/business/semiconductor/file/product/Exynos_5_Dual_User_Manaul_Public_REV100-0.pdf) > > "Four independent channels with asynchronous and serial input/output ports for general purpose (Channel 0 to 3), and One channel in ISP (ISP-UART Channel 0) > ? > ? Each UART contains a Baud-rate generator, a Transmitter, a Receiver and a Control Unit. The Baud-rate generator uses SCLK_UART." Each UART block uses independent clock source, i.e. UART0 uses SCLK_UART0 and UART3 uses SCLK_UART3. Do you have MUX_UART3 and DIV_UART3 configured properly? Do you have the IP bus clock (CLK_UART3) ungated? The public manual contains full description of clock tree and clock controller registers, so you should be able to figure this out. Best regards, Tomasz ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Enabling uart 3 in arndale 2014-03-14 8:04 ` [U-Boot] " armdev @ 2014-03-16 12:53 ` Tomasz Figa -1 siblings, 0 replies; 20+ messages in thread From: Tomasz Figa @ 2014-03-16 12:53 UTC (permalink / raw) To: armdev, Tushar Behera; +Cc: linux-samsung-soc, u-boot Hi, On 14.03.2014 09:04, armdev wrote: > Hi, > > We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as > > XuRXD3 : UART_3_RXD/GPA1[4] : 2 > XuTXD3 : UART_3_TXD/GPA1[5] : 4 > > As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) > Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. > > Can you please suggest what is the right procedure The register is GPA1CON and its GPA1CON[4] and [5] bit fields need both to be set to 0x2 - see Pad Control chapter of Exynos5250 public datasheet. Also GPA1PUD should be reconfigured to disable default pull-down on both pins, again you can find details of the register in the datasheet. Best regards, Tomasz ^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] Enabling uart 3 in arndale @ 2014-03-16 12:53 ` Tomasz Figa 0 siblings, 0 replies; 20+ messages in thread From: Tomasz Figa @ 2014-03-16 12:53 UTC (permalink / raw) To: u-boot Hi, On 14.03.2014 09:04, armdev wrote: > Hi, > > We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as > > XuRXD3 : UART_3_RXD/GPA1[4] : 2 > XuTXD3 : UART_3_TXD/GPA1[5] : 4 > > As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) > Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. > > Can you please suggest what is the right procedure The register is GPA1CON and its GPA1CON[4] and [5] bit fields need both to be set to 0x2 - see Pad Control chapter of Exynos5250 public datasheet. Also GPA1PUD should be reconfigured to disable default pull-down on both pins, again you can find details of the register in the datasheet. Best regards, Tomasz ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Enabling uart 3 in arndale 2014-03-16 12:53 ` [U-Boot] " Tomasz Figa @ 2014-03-28 9:42 ` armdev -1 siblings, 0 replies; 20+ messages in thread From: armdev @ 2014-03-28 9:42 UTC (permalink / raw) To: Tomasz Figa; +Cc: Tushar Behera, linux-samsung-soc, u-boot Dear Tomasz, On 16-Mar-2014, at 6:23 pm, Tomasz Figa <tomasz.figa@gmail.com> wrote: > Hi, > > On 14.03.2014 09:04, armdev wrote: >> Hi, >> >> We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as >> >> XuRXD3 : UART_3_RXD/GPA1[4] : 2 >> XuTXD3 : UART_3_TXD/GPA1[5] : 4 >> >> As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) >> Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. >> >> Can you please suggest what is the right procedure > > The register is GPA1CON and its GPA1CON[4] and [5] bit fields need both to be set to 0x2 - see Pad Control chapter of Exynos5250 public datasheet. Also GPA1PUD should be reconfigured to disable default pull-down on both pins, again you can find details of the register in the datasheet. > > Best regards, > Tomasz Based on the steps provided, we are still not able to get some output on UART3 simultaneously with UART2. Can you please help us find out what we are missing. On the current u-boot, Following was the observation and steps to enable UART3 on arndale Observations / Questions —————————————— a) The board has the default UART set to UART2 which is at 0x12c20000, while the include/configs/arndale.h has the UART_OFFSET set to 0x010000. Shouldn’t it be set to 0x20000 ? b) board_uart_init in board/samsung/arndale/arndale.c is configuring all the uarts, Clocks would be set properly for all 4 uarts ? Steps / Code Modified —————————————— a) GPAICON[4] and [5] set to 0x2 in board/samsung/arndale/arndale.c b) GPA1PUD [4] and [5] set to 0. diff --git a/board/samsung/arndale/arndale.c b/board/samsung/arndale/arndale.c index 9efc355..4fb291e 100644 --- a/board/samsung/arndale/arndale.c +++ b/board/samsung/arndale/arndale.c @@ -102,12 +102,18 @@ static int board_uart_init(void) int board_early_init_f(void) { int err; - + volatile unsigned int *gpa1con = (volatile unsigned int *)0x11400020; + volatile unsigned int *gpa1pud = (volatile unsigned int *)0x11400028; err = board_uart_init(); if (err) { debug("UART init failed\n"); return err; } + serial_init_dev(2); + serial_setbrg_dev(2); + *gpa1con |= 0x00220000; + *gpa1pud &= 0xfffff0ff; + return err; } #endif ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [U-Boot] Enabling uart 3 in arndale @ 2014-03-28 9:42 ` armdev 0 siblings, 0 replies; 20+ messages in thread From: armdev @ 2014-03-28 9:42 UTC (permalink / raw) To: u-boot Dear Tomasz, On 16-Mar-2014, at 6:23 pm, Tomasz Figa <tomasz.figa@gmail.com> wrote: > Hi, > > On 14.03.2014 09:04, armdev wrote: >> Hi, >> >> We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as >> >> XuRXD3 : UART_3_RXD/GPA1[4] : 2 >> XuTXD3 : UART_3_TXD/GPA1[5] : 4 >> >> As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) >> Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. >> >> Can you please suggest what is the right procedure > > The register is GPA1CON and its GPA1CON[4] and [5] bit fields need both to be set to 0x2 - see Pad Control chapter of Exynos5250 public datasheet. Also GPA1PUD should be reconfigured to disable default pull-down on both pins, again you can find details of the register in the datasheet. > > Best regards, > Tomasz Based on the steps provided, we are still not able to get some output on UART3 simultaneously with UART2. Can you please help us find out what we are missing. On the current u-boot, Following was the observation and steps to enable UART3 on arndale Observations / Questions ?????????????? a) The board has the default UART set to UART2 which is at 0x12c20000, while the include/configs/arndale.h has the UART_OFFSET set to 0x010000. Shouldn?t it be set to 0x20000 ? b) board_uart_init in board/samsung/arndale/arndale.c is configuring all the uarts, Clocks would be set properly for all 4 uarts ? Steps / Code Modified ?????????????? a) GPAICON[4] and [5] set to 0x2 in board/samsung/arndale/arndale.c b) GPA1PUD [4] and [5] set to 0. diff --git a/board/samsung/arndale/arndale.c b/board/samsung/arndale/arndale.c index 9efc355..4fb291e 100644 --- a/board/samsung/arndale/arndale.c +++ b/board/samsung/arndale/arndale.c @@ -102,12 +102,18 @@ static int board_uart_init(void) int board_early_init_f(void) { int err; - + volatile unsigned int *gpa1con = (volatile unsigned int *)0x11400020; + volatile unsigned int *gpa1pud = (volatile unsigned int *)0x11400028; err = board_uart_init(); if (err) { debug("UART init failed\n"); return err; } + serial_init_dev(2); + serial_setbrg_dev(2); + *gpa1con |= 0x00220000; + *gpa1pud &= 0xfffff0ff; + return err; } #endif ^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: Enabling uart 3 in arndale 2014-03-28 9:42 ` [U-Boot] " armdev @ 2014-03-31 3:47 ` armdev -1 siblings, 0 replies; 20+ messages in thread From: armdev @ 2014-03-31 3:47 UTC (permalink / raw) To: Tomasz Figa; +Cc: u-boot, linux-samsung-soc [-- Attachment #1.1: Type: text/plain, Size: 2649 bytes --] Dear tomaz Waiting for your reply... On 28-Mar-2014, at 3:12 pm, armdev <armdev.ftm@gmail.com> wrote: > Dear Tomasz, > > On 16-Mar-2014, at 6:23 pm, Tomasz Figa <tomasz.figa@gmail.com> wrote: > >> Hi, >> >> On 14.03.2014 09:04, armdev wrote: >>> Hi, >>> >>> We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as >>> >>> XuRXD3 : UART_3_RXD/GPA1[4] : 2 >>> XuTXD3 : UART_3_TXD/GPA1[5] : 4 >>> >>> As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) >>> Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. >>> >>> Can you please suggest what is the right procedure >> >> The register is GPA1CON and its GPA1CON[4] and [5] bit fields need both to be set to 0x2 - see Pad Control chapter of Exynos5250 public datasheet. Also GPA1PUD should be reconfigured to disable default pull-down on both pins, again you can find details of the register in the datasheet. >> >> Best regards, >> Tomasz > > Based on the steps provided, we are still not able to get some output on UART3 simultaneously with UART2. > Can you please help us find out what we are missing. > > On the current u-boot, Following was the observation and steps to enable UART3 on arndale > > Observations / Questions > —————————————— > a) The board has the default UART set to UART2 which is at 0x12c20000, while the include/configs/arndale.h has the UART_OFFSET set to 0x010000. > Shouldn’t it be set to 0x20000 ? > > b) board_uart_init in board/samsung/arndale/arndale.c is configuring all the uarts, > Clocks would be set properly for all 4 uarts ? > > Steps / Code Modified > —————————————— > a) GPAICON[4] and [5] set to 0x2 in board/samsung/arndale/arndale.c > b) GPA1PUD [4] and [5] set to 0. > > diff --git a/board/samsung/arndale/arndale.c b/board/samsung/arndale/arndale.c > index 9efc355..4fb291e 100644 > --- a/board/samsung/arndale/arndale.c > +++ b/board/samsung/arndale/arndale.c > @@ -102,12 +102,18 @@ static int board_uart_init(void) > int board_early_init_f(void) > { > int err; > - > + volatile unsigned int *gpa1con = (volatile unsigned int *)0x11400020; > + volatile unsigned int *gpa1pud = (volatile unsigned int *)0x11400028; > err = board_uart_init(); > if (err) { > debug("UART init failed\n"); > return err; > } > + serial_init_dev(2); > + serial_setbrg_dev(2); > + *gpa1con |= 0x00220000; > + *gpa1pud &= 0xfffff0ff; > + > return err; > } > #endif > [-- Attachment #2: Type: text/plain, Size: 134 bytes --] _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot ^ permalink raw reply [flat|nested] 20+ messages in thread
* [U-Boot] Enabling uart 3 in arndale @ 2014-03-31 3:47 ` armdev 0 siblings, 0 replies; 20+ messages in thread From: armdev @ 2014-03-31 3:47 UTC (permalink / raw) To: u-boot Dear tomaz Waiting for your reply... On 28-Mar-2014, at 3:12 pm, armdev <armdev.ftm@gmail.com> wrote: > Dear Tomasz, > > On 16-Mar-2014, at 6:23 pm, Tomasz Figa <tomasz.figa@gmail.com> wrote: > >> Hi, >> >> On 14.03.2014 09:04, armdev wrote: >>> Hi, >>> >>> We are trying to enable the UART3 on COM18 pins of arndale board. The UART3 RXD and TXD are on pins 2 and 4 which as per the base board specification is connected as >>> >>> XuRXD3 : UART_3_RXD/GPA1[4] : 2 >>> XuTXD3 : UART_3_TXD/GPA1[5] : 4 >>> >>> As per the public reference manual of exynos 5250, there is a register GPACON (0x1140_0000) >>> Setting GPACON |= 0x0010_0000 should enable the pins, but I am not able to see any output on UART3. >>> >>> Can you please suggest what is the right procedure >> >> The register is GPA1CON and its GPA1CON[4] and [5] bit fields need both to be set to 0x2 - see Pad Control chapter of Exynos5250 public datasheet. Also GPA1PUD should be reconfigured to disable default pull-down on both pins, again you can find details of the register in the datasheet. >> >> Best regards, >> Tomasz > > Based on the steps provided, we are still not able to get some output on UART3 simultaneously with UART2. > Can you please help us find out what we are missing. > > On the current u-boot, Following was the observation and steps to enable UART3 on arndale > > Observations / Questions > ?????????????? > a) The board has the default UART set to UART2 which is at 0x12c20000, while the include/configs/arndale.h has the UART_OFFSET set to 0x010000. > Shouldn?t it be set to 0x20000 ? > > b) board_uart_init in board/samsung/arndale/arndale.c is configuring all the uarts, > Clocks would be set properly for all 4 uarts ? > > Steps / Code Modified > ?????????????? > a) GPAICON[4] and [5] set to 0x2 in board/samsung/arndale/arndale.c > b) GPA1PUD [4] and [5] set to 0. > > diff --git a/board/samsung/arndale/arndale.c b/board/samsung/arndale/arndale.c > index 9efc355..4fb291e 100644 > --- a/board/samsung/arndale/arndale.c > +++ b/board/samsung/arndale/arndale.c > @@ -102,12 +102,18 @@ static int board_uart_init(void) > int board_early_init_f(void) > { > int err; > - > + volatile unsigned int *gpa1con = (volatile unsigned int *)0x11400020; > + volatile unsigned int *gpa1pud = (volatile unsigned int *)0x11400028; > err = board_uart_init(); > if (err) { > debug("UART init failed\n"); > return err; > } > + serial_init_dev(2); > + serial_setbrg_dev(2); > + *gpa1con |= 0x00220000; > + *gpa1pud &= 0xfffff0ff; > + > return err; > } > #endif > ^ permalink raw reply [flat|nested] 20+ messages in thread
end of thread, other threads:[~2014-03-31 3:47 UTC | newest] Thread overview: 20+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2014-03-14 8:04 Enabling uart 3 in arndale armdev 2014-03-14 8:04 ` [U-Boot] " armdev 2014-03-16 9:22 ` armdev 2014-03-16 9:22 ` [U-Boot] " armdev 2014-03-16 9:26 ` Michael Trimarchi 2014-03-16 9:26 ` Michael Trimarchi 2014-03-16 10:07 ` armdev 2014-03-16 10:07 ` armdev 2014-03-16 10:25 ` Michael Trimarchi 2014-03-16 10:25 ` Michael Trimarchi 2014-03-16 10:42 ` armdev 2014-03-16 10:42 ` armdev 2014-03-16 12:40 ` Tomasz Figa 2014-03-16 12:40 ` Tomasz Figa 2014-03-16 12:53 ` Tomasz Figa 2014-03-16 12:53 ` [U-Boot] " Tomasz Figa 2014-03-28 9:42 ` armdev 2014-03-28 9:42 ` [U-Boot] " armdev 2014-03-31 3:47 ` armdev 2014-03-31 3:47 ` [U-Boot] " armdev
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.