Re: [PATCH 10/13] tty: serial: omap: remove some dead code

[Nishanth Menon <nm@ti.com>]

On 04/23/2014 09:58 AM, Felipe Balbi wrote:
> nobody passes a DTR_gpio to this driver, so
> this code is not necessary.
> 
> Signed-off-by: Felipe Balbi <balbi@ti.com>
> ---

Niel,
this seems to revert the functionality introduced in
commit 9574f36fb801035f6ab0fbb1b53ce2c12c17d100
(OMAP/serial: Add support for driving a GPIO as DTR.)

would you like to Ack this change?

>  drivers/tty/serial/omap-serial.c | 39 ---------------------------------------
>  1 file changed, 39 deletions(-)
> 
> diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
> index b46aaf3..6654682 100644
> --- a/drivers/tty/serial/omap-serial.c
> +++ b/drivers/tty/serial/omap-serial.c
> @@ -163,10 +163,6 @@ struct uart_omap_port {
>  	u8			wakeups_enabled;
>  	u32			features;
>  
> -	int			DTR_gpio;
> -	int			DTR_inverted;
> -	int			DTR_active;
> -
>  	struct serial_rs485	rs485;
>  	int			rts_gpio;
>  
> @@ -694,16 +690,6 @@ static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
>  	serial_out(up, UART_MCR, up->mcr);
>  	pm_runtime_mark_last_busy(up->dev);
>  	pm_runtime_put_autosuspend(up->dev);
> -
> -	if (gpio_is_valid(up->DTR_gpio) &&
> -	    !!(mctrl & TIOCM_DTR) != up->DTR_active) {
> -		up->DTR_active = !up->DTR_active;
> -		if (gpio_cansleep(up->DTR_gpio))
> -			schedule_work(&up->qos_work);
> -		else
> -			gpio_set_value(up->DTR_gpio,
> -				       up->DTR_active != up->DTR_inverted);
> -	}
>  }
>  
>  static void serial_omap_break_ctl(struct uart_port *port, int break_state)
> @@ -847,9 +833,6 @@ static void serial_omap_uart_qos_work(struct work_struct *work)
>  						qos_work);
>  
>  	pm_qos_update_request(&up->pm_qos_request, up->latency);
> -	if (gpio_is_valid(up->DTR_gpio))
> -		gpio_set_value_cansleep(up->DTR_gpio,
> -					up->DTR_active != up->DTR_inverted);
>  }
>  
>  static void
> @@ -1672,28 +1655,6 @@ static int serial_omap_probe(struct platform_device *pdev)
>  	if (IS_ERR(base))
>  		return PTR_ERR(base);
>  
> -	if (gpio_is_valid(omap_up_info->DTR_gpio) &&
> -	    omap_up_info->DTR_present) {
> -		ret = devm_gpio_request(&pdev->dev, omap_up_info->DTR_gpio,
> -				"omap-serial");
> -		if (ret < 0)
> -			return ret;
> -		ret = gpio_direction_output(omap_up_info->DTR_gpio,
> -					    omap_up_info->DTR_inverted);
> -		if (ret < 0)
> -			return ret;
> -	}
> -
> -	if (gpio_is_valid(omap_up_info->DTR_gpio) &&
> -	    omap_up_info->DTR_present) {
> -		up->DTR_gpio = omap_up_info->DTR_gpio;
> -		up->DTR_inverted = omap_up_info->DTR_inverted;
> -	} else {
> -		up->DTR_gpio = -EINVAL;
> -	}
> -
> -	up->DTR_active = 0;
> -
>  	up->dev = &pdev->dev;
>  	up->port.dev = &pdev->dev;
>  	up->port.type = PORT_OMAP;
> 


-- 
Regards,
Nishanth Menon