[U-Boot] [PATCH 03/12] MX6: add common SPL configuration

[Stefano Babic <sbabic@denx.de>]

Hi Tim,

On 28/04/2014 22:17, Tim Harvey wrote:
> Add a common header which can hopefully be shared amon imx6 SPL users
> 
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> ---
> v2:
> - adjust CONFIG_SPL_TEXT_BASE, CONFIG_SPL_STACK and CONFIG_SPL_MAX_SIZE
>   to accomodate the IMX6SOLO/DUALLITE which have half the iRAM of the
>   IMX6DUAL/IMX6QUAD
> ---
>  include/configs/imx6_spl.h | 71 ++++++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 71 insertions(+)
>  create mode 100644 include/configs/imx6_spl.h
> 
> diff --git a/include/configs/imx6_spl.h b/include/configs/imx6_spl.h
> new file mode 100644
> index 0000000..20078cc
> --- /dev/null
> +++ b/include/configs/imx6_spl.h
> @@ -0,0 +1,71 @@
> +/*
> + * Copyright (C) 2014 Gateworks Corporation
> + * Author: Tim Harvey <tharvey@gateworks.com>
> + *
> + * SPDX-License-Identifier:     GPL-2.0+
> + */
> +#ifndef __IMX6_SPL_CONFIG_H
> +#define __IMX6_SPL_CONFIG_H
> +
> +#ifdef CONFIG_SPL
> +
> +#define CONFIG_SPL_FRAMEWORK
> +
> +/*
> + * see Figure 8-3 in IMX6DQ/IMX6SDL Reference manuals:
> + *  - IMX6 OCRAM (IRAM) is from 0x00907000 to 0x0091FFFF (IMX6SLD)
> + *  - IMX6DQ has 2x IRAM of IMX6SLD but we intend to support IMX6SLD as well
> + *  - BOOT ROM stack is at 0x0091FFB8
> + *  - if icache/dcache is enabled (eFuse/strapping controlled) then the
> + *    IMX BOOT ROM will setup MMU table at 0x00918000, therefore we need to
> + *    fit between 0x00907000 and 0x00918000.
> + *  - Additionally the BOOT ROM loads what they consider the firmware image
> + *    which consists of a 4K header in front of us that contains the IVT, DCD
> + *    and some padding thus 'our' max size is really 0x00908000 - 0x00918000
> + *    or 64KB
> + */
> +#define CONFIG_SPL_LDSCRIPT	"arch/arm/cpu/armv7/omap-common/u-boot-spl.lds"
> +#define CONFIG_SPL_TEXT_BASE		0x00908000
> +#define CONFIG_SPL_MAX_SIZE		(64 * 1024)
> +#define CONFIG_SPL_START_S_PATH		"arch/arm/cpu/armv7"
> +#define CONFIG_SPL_STACK		0x0091FFB8
> +#define CONFIG_SPL_LIBCOMMON_SUPPORT
> +#define CONFIG_SPL_LIBGENERIC_SUPPORT
> +#define CONFIG_SPL_SERIAL_SUPPORT
> +#define CONFIG_SPL_I2C_SUPPORT
> +#define CONFIG_SPL_GPIO_SUPPORT
> +
> +/* NAND support */
> +#if defined(CONFIG_SPL_NAND_SUPPORT)
> +#define CONFIG_SPL_NAND_MXS
> +#define CONFIG_SPL_DMA_SUPPORT
> +#endif
> +
> +/* MMC support */
> +#if defined(CONFIG_SPL_MMC_SUPPORT)
> +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	138 /* offset 69KB */
> +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	800 /* 400 KB */
> +#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION	1
> +#define CONFIG_SYS_MONITOR_LEN  (CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS/2*1024)
> +#endif
> +
> +/* SATA support */
> +#if defined(CONFIG_SPL_SATA_SUPPORT)
> +#define CONFIG_SPL_SATA_BOOT_DEVICE		0
> +#define CONFIG_SYS_SATA_FAT_BOOT_PARTITION	1
> +#endif
> +
> +/* Define the payload for FAT/EXT support */
> +#if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
> +#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME  "u-boot.img"
> +#define CONFIG_SPL_LIBDISK_SUPPORT
> +#endif
> +
> +#define CONFIG_SPL_BSS_START_ADDR	0x18200000
> +#define CONFIG_SPL_BSS_MAX_SIZE		0x100000	/* 1 MB */
> +#define CONFIG_SYS_SPL_MALLOC_START	0x18300000
> +#define CONFIG_SYS_SPL_MALLOC_SIZE	0x3200000	/* 50 MB */
> +#define CONFIG_SYS_TEXT_BASE		0x17800000
> +#endif
> +
> +#endif
> 

I generally agree with the idea having a common setup - this simplifies
porting of new boards to SPL !

Apart the small typos found by Eric/Igor:

Acked-by: Stefano Babic <sbabic@denx.de>

Best regards,
Stefano Babic


-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================