From: Balaji T K <balajitk@ti.com>
To: Andreas Fenkart <afenkart@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>, Chris Ball <chris@printf.net>,
Grant Likely <grant.likely@secretlab.ca>,
Felipe Balbi <balbi@ti.com>,
Andreas Mueller <schnitzeltony@googlemail.com>,
zonque@gmail.com, galak@codeaurora.org,
linux-doc@vger.kernel.org, linux-mmc@vger.kernel.org,
linux-omap@vger.kernel.org
Subject: Re: [PATCH v11 6/7] mmc: omap_hsmmc: switch default/idle pinctrl states in runtime hooks
Date: Fri, 9 May 2014 22:41:52 +0530 [thread overview]
Message-ID: <536D0C58.8080408@ti.com> (raw)
In-Reply-To: <1399591234-13089-6-git-send-email-afenkart@gmail.com>
On Friday 09 May 2014 04:50 AM, Andreas Fenkart wrote:
> These are predefined states of the driver model. When not present,
> as if not set in the device tree, they become no-ops.
> Explicitly selecting the default state is not needed since the
> device core layer sets pin mux to "default" state before probe.
> This is not the simplest implementation, on AM335x at least, we could
> switch to idle at any point in the suspend hook, only the default state
> needs to be set before writing to the irq registers or an IRQ might get
> lost.
>
> Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
>
> diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
> index 47a5982..5a321f98 100644
> --- a/drivers/mmc/host/omap_hsmmc.c
> +++ b/drivers/mmc/host/omap_hsmmc.c
> @@ -2032,7 +2032,6 @@ static int omap_hsmmc_probe(struct platform_device *pdev)
> const struct of_device_id *match;
> dma_cap_mask_t mask;
> unsigned tx_req, rx_req;
> - struct pinctrl *pinctrl;
> const struct omap_mmc_of_data *data;
>
> apply_clk_hack(&pdev->dev);
Looks like this patches is not based on mmc-next[1]
Can you please rebase to mmc-next
[1] http://git.kernel.org/cgit/linux/kernel/git/cjb/mmc.git/log/?id=refs/heads/mmc-next
Other than that:
Acked-by: Balaji T K <balajitk@ti.com>
> @@ -2258,11 +2257,6 @@ static int omap_hsmmc_probe(struct platform_device *pdev)
>
> omap_hsmmc_disable_irq(host);
>
> - pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
> - if (IS_ERR(pinctrl))
> - dev_warn(&pdev->dev,
> - "pins are not configured from the driver\n");
> -
> /*
> * For now, only support SDIO interrupt if we have a separate
> * wake-up interrupt configured from device tree. This is because
> @@ -2486,10 +2480,15 @@ static int omap_hsmmc_runtime_suspend(struct device *dev)
> goto abort;
> }
>
> + pinctrl_pm_select_idle_state(dev);
> +
> WARN_ON(host->flags & HSMMC_WAKE_IRQ_ENABLED);
> enable_irq(host->wake_irq);
> host->flags |= HSMMC_WAKE_IRQ_ENABLED;
> + } else {
> + pinctrl_pm_select_idle_state(dev);
> }
> +
> abort:
> spin_unlock_irqrestore(&host->irq_lock, flags);
> return ret;
> @@ -2513,9 +2512,14 @@ static int omap_hsmmc_runtime_resume(struct device *dev)
> host->flags &= ~HSMMC_WAKE_IRQ_ENABLED;
> }
>
> + pinctrl_pm_select_default_state(host->dev);
> +
> + /* irq lost, if pinmux incorrect */
> OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
> OMAP_HSMMC_WRITE(host->base, ISE, CIRQ_EN);
> OMAP_HSMMC_WRITE(host->base, IE, CIRQ_EN);
> + } else {
> + pinctrl_pm_select_default_state(host->dev);
> }
> spin_unlock_irqrestore(&host->irq_lock, flags);
> return 0;
>
next prev parent reply other threads:[~2014-05-09 17:12 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-05-08 23:16 [PATCH v11 0/7] mmc: omap_hsmmc: Enable SDIO IRQ Andreas Fenkart
2014-05-08 23:20 ` [PATCH v11 1/7] mmc: omap_hsmmc: compile fix for !CONFIG_OF build Andreas Fenkart
2014-05-08 23:20 ` [PATCH v11 2/7] mmc: omap_hsmmc: Enable SDIO interrupt Andreas Fenkart
2014-05-09 17:09 ` Balaji T K
2014-05-08 23:20 ` [PATCH v11 3/7] mmc: omap_hsmmc: enable wakeup event for sdio OMAP4 Andreas Fenkart
2014-05-08 23:20 ` [PATCH v11 4/7] mmc: omap_hsmmc: Extend debugfs by SDIO IRQ handling, runtime state Andreas Fenkart
2014-05-09 17:10 ` Balaji T K
2014-05-08 23:20 ` [PATCH v11 5/7] mmc: omap_hsmmc: abort runtime suspend if pending sdio irq detected Andreas Fenkart
2014-05-09 17:10 ` Balaji T K
2014-05-08 23:20 ` [PATCH v11 6/7] mmc: omap_hsmmc: switch default/idle pinctrl states in runtime hooks Andreas Fenkart
2014-05-09 17:11 ` Balaji T K [this message]
2014-05-08 23:20 ` [PATCH v11 7/7] mmc: omap_hsmmc: Pin remux workaround to support SDIO interrupt on AM335x Andreas Fenkart
2014-05-09 17:11 ` Balaji T K
2014-05-08 23:48 ` [PATCH v11 1/7] mmc: omap_hsmmc: compile fix for !CONFIG_OF build Sebastian Reichel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=536D0C58.8080408@ti.com \
--to=balajitk@ti.com \
--cc=afenkart@gmail.com \
--cc=balbi@ti.com \
--cc=chris@printf.net \
--cc=galak@codeaurora.org \
--cc=grant.likely@secretlab.ca \
--cc=linux-doc@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=schnitzeltony@googlemail.com \
--cc=tony@atomide.com \
--cc=zonque@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.