From: Wei Huang <w1.huang@samsung.com>
To: Julien Grall <julien.grall@linaro.org>, xen-devel@lists.xen.org
Cc: keir@xen.org, ian.campbell@citrix.com,
stefano.stabellini@eu.citrix.com, andrew.cooper3@citrix.com,
tim@xen.org, jaeyong.yoo@samsung.com, jbeulich@suse.com,
ian.jackson@eu.citrix.com, yjhyun.yoo@samsung.com
Subject: Re: [RFC v3 0/6] xen/arm: ARM save/restore/migration support
Date: Mon, 12 May 2014 09:52:04 -0500 [thread overview]
Message-ID: <5370E014.6040103@samsung.com> (raw)
In-Reply-To: <5370D7F3.3040700@linaro.org>
On 05/12/2014 09:17 AM, Julien Grall wrote:
> Hi Wei,
>
> On 05/08/2014 10:18 PM, Wei Huang wrote:
>> The following patches enable save/restore/migration support for ARM
>> guest VMs. Note that the original series were sent from Jaeyong Yoo.
>>
>> Working:
>> * 32-bit (including SMP) guest VM save/restore/migration
>> * 64-bit guest VM save
>> WIP:
>> * 64-bit guest restore/migration
>
> I though a bit more about this series. I think we miss to save the
> layout of the guest (i.e GIC base address, gnttab base address,...) and
> some interrupts (i.e timer, evtchn,...)
>
> It's necessary because if we migrate from a older Xen to a new Xen, the
> default layout may have change.
>
Should we make these requirements as phase 2 for save/restore/migration?
I think we have enough items to fix in current form. Adding more
requirements will make the whole patch set bloated and hard to revise.
-Wei
> Regards,
>
next prev parent reply other threads:[~2014-05-12 14:52 UTC|newest]
Thread overview: 67+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-05-08 21:18 [RFC v3 0/6] xen/arm: ARM save/restore/migration support Wei Huang
2014-05-08 21:18 ` [RFC v3 1/6] xen/arm: Add basic save/restore support for ARM Wei Huang
2014-05-08 22:11 ` Andrew Cooper
2014-05-08 22:20 ` Wei Huang
2014-05-09 8:56 ` Julien Grall
2014-05-14 10:27 ` Ian Campbell
2014-05-14 10:25 ` Ian Campbell
2014-05-14 10:46 ` Andrew Cooper
2014-05-14 13:22 ` Ian Campbell
2014-05-09 9:06 ` Julien Grall
2014-05-09 9:42 ` Jan Beulich
2014-05-14 10:37 ` Ian Campbell
2014-05-14 18:54 ` Wei Huang
2014-05-08 21:18 ` [RFC v3 2/6] xen/arm: Add save/restore support for ARM GIC V2 Wei Huang
2014-05-08 22:47 ` Andrew Cooper
2014-05-09 14:12 ` Wei Huang
2014-05-09 14:24 ` Ian Campbell
2014-05-11 16:15 ` Julien Grall
2014-05-13 14:53 ` Wei Huang
2014-05-09 9:17 ` Julien Grall
2014-05-14 11:07 ` Ian Campbell
2014-05-14 12:05 ` Julien Grall
2014-05-14 12:23 ` Tim Deegan
2014-05-14 13:24 ` Ian Campbell
2014-05-15 17:15 ` Julien Grall
2014-05-16 7:36 ` Ian Campbell
2014-05-08 21:18 ` [RFC v3 3/6] xen/arm: Add save/restore support for ARM arch timer Wei Huang
2014-05-08 23:02 ` Andrew Cooper
2014-05-11 9:01 ` Julien Grall
2014-05-11 8:58 ` Julien Grall
2014-05-12 8:35 ` Ian Campbell
2014-05-12 11:42 ` Julien Grall
2014-05-14 11:14 ` Ian Campbell
2014-05-14 12:13 ` Julien Grall
2014-05-14 13:23 ` Ian Campbell
2014-05-14 19:04 ` Wei Huang
2014-05-08 21:18 ` [RFC v3 4/6] xen/arm: Add save/restore support for guest core registers Wei Huang
2014-05-08 23:10 ` Andrew Cooper
2014-05-09 16:35 ` Wei Huang
2014-05-09 16:52 ` Ian Campbell
2014-05-11 9:06 ` Julien Grall
2014-05-14 11:16 ` Ian Campbell
2014-05-14 12:23 ` Julien Grall
2014-05-14 13:25 ` Ian Campbell
2014-05-14 13:31 ` Julien Grall
2014-05-14 11:37 ` Ian Campbell
2014-05-08 21:18 ` [RFC v3 5/6] xen/arm: Add log_dirty support for ARM Wei Huang
2014-05-08 23:46 ` Andrew Cooper
2014-05-14 11:51 ` Ian Campbell
2014-05-11 15:28 ` Julien Grall
2014-05-12 14:00 ` Wei Huang
2014-05-12 14:11 ` Julien Grall
2014-05-14 12:04 ` Ian Campbell
2014-05-14 11:57 ` Ian Campbell
2014-05-14 12:20 ` Julien Grall
2014-05-14 13:24 ` Ian Campbell
2014-05-14 13:18 ` Ian Campbell
2014-05-16 10:59 ` Julien Grall
2014-05-08 21:18 ` [RFC v3 6/6] xen/arm: Implement toolstack for xl restore/save/migration Wei Huang
2014-05-14 13:20 ` Ian Campbell
2014-05-14 13:24 ` Andrew Cooper
2014-05-11 9:23 ` [RFC v3 0/6] xen/arm: ARM save/restore/migration support Julien Grall
2014-05-12 14:37 ` Wei Huang
2014-05-13 14:41 ` Julien Grall
2014-05-12 14:17 ` Julien Grall
2014-05-12 14:52 ` Wei Huang [this message]
2014-05-12 15:01 ` Ian Campbell
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5370E014.6040103@samsung.com \
--to=w1.huang@samsung.com \
--cc=andrew.cooper3@citrix.com \
--cc=ian.campbell@citrix.com \
--cc=ian.jackson@eu.citrix.com \
--cc=jaeyong.yoo@samsung.com \
--cc=jbeulich@suse.com \
--cc=julien.grall@linaro.org \
--cc=keir@xen.org \
--cc=stefano.stabellini@eu.citrix.com \
--cc=tim@xen.org \
--cc=xen-devel@lists.xen.org \
--cc=yjhyun.yoo@samsung.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.