All of lore.kernel.org
 help / color / mirror / Atom feed
From: marc.zyngier@arm.com (Marc Zyngier)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v6 03/15] irq: gic: support hip04 gic
Date: Thu, 15 May 2014 10:34:35 +0100	[thread overview]
Message-ID: <53748A2B.9050304@arm.com> (raw)
In-Reply-To: <1399795571-17231-4-git-send-email-haojian.zhuang@linaro.org>

On 11/05/14 09:05, Haojian Zhuang wrote:
> There's a little difference between ARM GIC and HiP04 GIC.
> 
> * HiP04 GIC could support 16 cores at most, and ARM GIC could support
> 8 cores at most. So the difination on GIC_DIST_TARGET registers are
> different since CPU interfaces are increased from 8-bit to 16-bit.
> 
> * HiP04 GIC could support 510 interrupts at most, and ARM GIC could
> support 1020 interrupts at most.
> 
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
> ---
>  Documentation/devicetree/bindings/arm/gic.txt |   1 +
>  drivers/irqchip/irq-gic.c                     | 160 ++++++++++++++++++++------
>  2 files changed, 129 insertions(+), 32 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt
> index 5573c08..150f7d6 100644
> --- a/Documentation/devicetree/bindings/arm/gic.txt
> +++ b/Documentation/devicetree/bindings/arm/gic.txt
> @@ -16,6 +16,7 @@ Main node required properties:
>         "arm,cortex-a9-gic"
>         "arm,cortex-a7-gic"
>         "arm,arm11mp-gic"
> +       "hisilicon,hip04-gic"
>  - interrupt-controller : Identifies the node as an interrupt controller
>  - #interrupt-cells : Specifies the number of cells needed to encode an
>    interrupt source.  The type shall be a <u32> and the value shall be 3.
> diff --git a/drivers/irqchip/irq-gic.c b/drivers/irqchip/irq-gic.c
> index f711fb6..d1d1430 100644
> --- a/drivers/irqchip/irq-gic.c
> +++ b/drivers/irqchip/irq-gic.c
> @@ -68,6 +68,7 @@ struct gic_chip_data {
>  #ifdef CONFIG_GIC_NON_BANKED
>         void __iomem *(*get_base)(union gic_base *);
>  #endif
> +       u32 nr_cpu_if;
>  };
> 
>  static DEFINE_RAW_SPINLOCK(irq_controller_lock);
> @@ -76,9 +77,11 @@ static DEFINE_RAW_SPINLOCK(irq_controller_lock);
>   * The GIC mapping of CPU interfaces does not necessarily match
>   * the logical CPU numbering.  Let's use a mapping as returned
>   * by the GIC itself.
> + *
> + * Hisilicon HiP04 extends the number of CPU interface from 8 to 16.
>   */
> -#define NR_GIC_CPU_IF 8
> -static u8 gic_cpu_map[NR_GIC_CPU_IF] __read_mostly;
> +#define NR_GIC_CPU_IF  16
> +static u16 gic_cpu_map[NR_GIC_CPU_IF] __read_mostly;
> 
>  /*
>   * Supported arch specific GIC irq extension.
> @@ -241,20 +244,64 @@ static int gic_retrigger(struct irq_data *d)
>         return 0;
>  }
> 
> +static inline bool gic_is_standard(struct gic_chip_data *gic)

Please loose all of the inlines. The compiler can do this by itself.

> +{
> +       return (gic->nr_cpu_if == 8);
> +}
> +
> +static inline int gic_irqs_per_target_reg(struct gic_chip_data *gic)
> +{
> +       return 32 / gic->nr_cpu_if;
> +}
> +
>  #ifdef CONFIG_SMP
> +static inline u32 irq_to_target_reg(struct irq_data *d)
> +{
> +       struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d);
> +       unsigned int i = gic_irq(d);
> +
> +       if (gic_is_standard(gic_data))
> +               i = i & ~3U;
> +       else
> +               i = (i << 1) & ~3U;
> +       return (i + GIC_DIST_TARGET);
> +}
> +
> +static inline u32 irq_to_core_shift(struct irq_data *d)
> +{
> +       struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d);
> +       unsigned int i = gic_irq(d);
> +
> +       if (gic_is_standard(gic_data))
> +               return ((i % 4) << 3);
> +       return ((i % 2) << 4);
> +}
> +
> +static inline u32 irq_to_core_mask(struct irq_data *d)
> +{
> +       struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d);
> +       u32 mask;
> +       /* ARM GIC, nr_cpu_if == 8; HiP04 GIC, nr_cpu_if == 16 */
> +       mask = (1 << gic_data->nr_cpu_if) - 1;
> +       return (mask << irq_to_core_shift(d));
> +}
> +
>  static int gic_set_affinity(struct irq_data *d, const struct cpumask *mask_val,
>                             bool force)
>  {
> -       void __iomem *reg = gic_dist_base(d) + GIC_DIST_TARGET + (gic_irq(d) & ~3);
> -       unsigned int shift = (gic_irq(d) % 4) * 8;
> +       void __iomem *reg;
> +       struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d);
> +       unsigned int shift = irq_to_core_shift(d);
>         unsigned int cpu = cpumask_any_and(mask_val, cpu_online_mask);
>         u32 val, mask, bit;
> 
> -       if (cpu >= NR_GIC_CPU_IF || cpu >= nr_cpu_ids)
> +       if (cpu >= gic_data->nr_cpu_if || cpu >= nr_cpu_ids)
>                 return -EINVAL;
> 
> +       reg = gic_dist_base(d) + irq_to_target_reg(d);
> +
>         raw_spin_lock(&irq_controller_lock);
> -       mask = 0xff << shift;
> +       mask = irq_to_core_mask(d);
>         bit = gic_cpu_map[cpu] << shift;
>         val = readl_relaxed(reg) & ~mask;
>         writel_relaxed(val | bit, reg);
> @@ -354,15 +401,24 @@ void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq)
>         irq_set_chained_handler(irq, gic_handle_cascade_irq);
>  }
> 
> -static u8 gic_get_cpumask(struct gic_chip_data *gic)
> +static u16 gic_get_cpumask(struct gic_chip_data *gic)
>  {
>         void __iomem *base = gic_data_dist_base(gic);
>         u32 mask, i;
> 
> -       for (i = mask = 0; i < 32; i += 4) {
> -               mask = readl_relaxed(base + GIC_DIST_TARGET + i);
> -               mask |= mask >> 16;
> -               mask |= mask >> 8;
> +       /*
> +        * ARM GIC uses 8 registers for interrupt 0-31,
> +        * HiP04 GIC uses 16 registers for interrupt 0-31.
> +        */
> +       for (i = mask = 0; i < 32; i += gic_irqs_per_target_reg(gic)) {
> +               if (gic_is_standard(gic)) {
> +                       mask = readl_relaxed(base + GIC_DIST_TARGET + i);
> +                       mask |= mask >> 16;
> +                       mask |= mask >> 8;
> +               } else {                        /* HiP04 GIC */
> +                       mask = readl_relaxed(base + GIC_DIST_TARGET + i * 2);
> +                       mask |= mask >> 16;
> +               }

You have irq_to_target_reg now, and you can rewrite most of this without
duplication (see my previous review comment).

>                 if (mask)
>                         break;
>         }
> @@ -370,6 +426,10 @@ static u8 gic_get_cpumask(struct gic_chip_data *gic)
>         if (!mask)
>                 pr_crit("GIC CPU mask not found - kernel will fail to boot.\n");
> 
> +       /* ARM GIC needs 8-bit cpu mask, HiP04 GIC needs 16-bit cpu mask. */
> +       if (gic_is_standard(gic))
> +               mask &= 0xff;
> +
>         return mask;
>  }
> 
> @@ -392,10 +452,17 @@ static void __init gic_dist_init(struct gic_chip_data *gic)
>          * Set all global interrupts to this CPU only.
>          */
>         cpumask = gic_get_cpumask(gic);
> -       cpumask |= cpumask << 8;
> +       if (gic_is_standard(gic))
> +               cpumask |= cpumask << 8;
>         cpumask |= cpumask << 16;
> -       for (i = 32; i < gic_irqs; i += 4)
> -               writel_relaxed(cpumask, base + GIC_DIST_TARGET + i * 4 / 4);
> +       for (i = 32; i < gic_irqs; i += gic_irqs_per_target_reg(gic)) {
> +               if (gic_is_standard(gic))
> +                       writel_relaxed(cpumask,
> +                                      base + GIC_DIST_TARGET + i / 4 * 4);
> +               else
> +                       writel_relaxed(cpumask,
> +                                      base + GIC_DIST_TARGET + i / 2 * 4);
> +       }

Same here.

> 
>         /*
>          * Set priority on all global interrupts.
> @@ -423,7 +490,7 @@ static void gic_cpu_init(struct gic_chip_data *gic)
>         /*
>          * Get what the GIC says our CPU mask is.
>          */
> -       BUG_ON(cpu >= NR_GIC_CPU_IF);
> +       BUG_ON(cpu >= gic->nr_cpu_if);
>         cpu_mask = gic_get_cpumask(gic);
>         gic_cpu_map[cpu] = cpu_mask;
> 
> @@ -431,7 +498,7 @@ static void gic_cpu_init(struct gic_chip_data *gic)
>          * Clear our mask from the other map entries in case they're
>          * still undefined.
>          */
> -       for (i = 0; i < NR_GIC_CPU_IF; i++)
> +       for (i = 0; i < gic->nr_cpu_if; i++)
>                 if (i != cpu)
>                         gic_cpu_map[i] &= ~cpu_mask;
> 
> @@ -467,7 +534,7 @@ void gic_cpu_if_down(void)
>   */
>  static void gic_dist_save(unsigned int gic_nr)
>  {
> -       unsigned int gic_irqs;
> +       unsigned int gic_irqs, nr_irq_per_target;
>         void __iomem *dist_base;
>         int i;
> 
> @@ -476,6 +543,7 @@ static void gic_dist_save(unsigned int gic_nr)
> 
>         gic_irqs = gic_data[gic_nr].gic_irqs;
>         dist_base = gic_data_dist_base(&gic_data[gic_nr]);
> +       nr_irq_per_target = gic_irqs_per_target_reg(&gic_data[gic_nr]);
> 
>         if (!dist_base)
>                 return;
> @@ -484,7 +552,7 @@ static void gic_dist_save(unsigned int gic_nr)
>                 gic_data[gic_nr].saved_spi_conf[i] =
>                         readl_relaxed(dist_base + GIC_DIST_CONFIG + i * 4);
> 
> -       for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++)
> +       for (i = 0; i < DIV_ROUND_UP(gic_irqs, nr_irq_per_target); i++)
>                 gic_data[gic_nr].saved_spi_target[i] =
>                         readl_relaxed(dist_base + GIC_DIST_TARGET + i * 4);
> 
> @@ -502,7 +570,7 @@ static void gic_dist_save(unsigned int gic_nr)
>   */
>  static void gic_dist_restore(unsigned int gic_nr)
>  {
> -       unsigned int gic_irqs;
> +       unsigned int gic_irqs, nr_irq_per_target;
>         unsigned int i;
>         void __iomem *dist_base;
> 
> @@ -511,6 +579,7 @@ static void gic_dist_restore(unsigned int gic_nr)
> 
>         gic_irqs = gic_data[gic_nr].gic_irqs;
>         dist_base = gic_data_dist_base(&gic_data[gic_nr]);
> +       nr_irq_per_target = gic_irqs_per_target_reg(&gic_data[gic_nr]);
> 
>         if (!dist_base)
>                 return;
> @@ -525,7 +594,7 @@ static void gic_dist_restore(unsigned int gic_nr)
>                 writel_relaxed(0xa0a0a0a0,
>                         dist_base + GIC_DIST_PRI + i * 4);
> 
> -       for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++)
> +       for (i = 0; i < DIV_ROUND_UP(gic_irqs, nr_irq_per_target); i++)
>                 writel_relaxed(gic_data[gic_nr].saved_spi_target[i],
>                         dist_base + GIC_DIST_TARGET + i * 4);
> 
> @@ -665,9 +734,19 @@ static void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
>          */
>         dmb(ishst);
> 
> -       /* this always happens on GIC0 */
> -       writel_relaxed(map << 16 | irq, gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT);
> -
> +       /*
> +        * CPUTargetList -- bit[23:16] in GIC_DIST_SOFTINT in ARM GIC.
> +        *                  bit[23:8] in GIC_DIST_SOFTINT in HiP04 GIC.
> +        * NSATT -- bit[15] in GIC_DIST_SOFTINT in ARM GIC.
> +        *          bit[7] in GIC_DIST_SOFTINT in HiP04 GIC.
> +        * this always happens on GIC0
> +        */
> +       if (gic_is_standard(&gic_data[0]))
> +               map = map << 16;
> +       else
> +               map = map << 8;
> +       writel_relaxed(map | irq,
> +                      gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT);
>         raw_spin_unlock_irqrestore(&irq_controller_lock, flags);
>  }
>  #endif
> @@ -681,10 +760,15 @@ static void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
>   */
>  void gic_send_sgi(unsigned int cpu_id, unsigned int irq)
>  {
> -       BUG_ON(cpu_id >= NR_GIC_CPU_IF);
> +       BUG_ON(cpu_id >= gic_data[0].nr_cpu_if);
>         cpu_id = 1 << cpu_id;
>         /* this always happens on GIC0 */
> -       writel_relaxed((cpu_id << 16) | irq, gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT);
> +       if (gic_is_standard(&gic_data[0]))
> +               cpu_id = cpu_id << 16;
> +       else
> +               cpu_id = cpu_id << 8;
> +       writel_relaxed(cpu_id | irq,
> +                      gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT);
>  }
> 
>  /*
> @@ -700,7 +784,7 @@ int gic_get_cpu_id(unsigned int cpu)
>  {
>         unsigned int cpu_bit;
> 
> -       if (cpu >= NR_GIC_CPU_IF)
> +       if (cpu >= gic_data[0].nr_cpu_if)
>                 return -1;
>         cpu_bit = gic_cpu_map[cpu];
>         if (cpu_bit & (cpu_bit - 1))
> @@ -931,7 +1015,7 @@ void __init gic_init_bases(unsigned int gic_nr, int irq_start,
>         irq_hw_number_t hwirq_base;
>         struct gic_chip_data *gic;
>         int gic_irqs, irq_base, i;
> -       int nr_routable_irqs;
> +       int nr_routable_irqs, max_nr_irq;
> 
>         BUG_ON(gic_nr >= MAX_GIC_NR);
> 
> @@ -967,12 +1051,22 @@ void __init gic_init_bases(unsigned int gic_nr, int irq_start,
>                 gic_set_base_accessor(gic, gic_get_common_base);
>         }
> 
> +       if (of_device_is_compatible(node, "hisilicon,hip04-gic")) {
> +               /* HiP04 GIC supports 16 CPUs at most */
> +               gic->nr_cpu_if = 16;
> +               max_nr_irq = 510;
> +       } else {
> +               /* ARM/Qualcomm GIC supports 8 CPUs at most */
> +               gic->nr_cpu_if = 8;
> +               max_nr_irq = 1020;
> +       }
> +
>         /*
>          * Initialize the CPU interface map to all CPUs.
>          * It will be refined as each CPU probes its ID.
>          */
> -       for (i = 0; i < NR_GIC_CPU_IF; i++)
> -               gic_cpu_map[i] = 0xff;
> +       for (i = 0; i < gic->nr_cpu_if; i++)
> +               gic_cpu_map[i] = (1 << gic->nr_cpu_if) - 1;
> 
>         /*
>          * For primary GICs, skip over SGIs.
> @@ -988,12 +1082,13 @@ void __init gic_init_bases(unsigned int gic_nr, int irq_start,
> 
>         /*
>          * Find out how many interrupts are supported.
> -        * The GIC only supports up to 1020 interrupt sources.
> +        * The ARM/Qualcomm GIC only supports up to 1020 interrupt sources.
> +        * The HiP04 GIC only supports up to 510 interrupt sources.
>          */
>         gic_irqs = readl_relaxed(gic_data_dist_base(gic) + GIC_DIST_CTR) & 0x1f;
>         gic_irqs = (gic_irqs + 1) * 32;
> -       if (gic_irqs > 1020)
> -               gic_irqs = 1020;
> +       if (gic_irqs > max_nr_irq)
> +               gic_irqs = max_nr_irq;
>         gic->gic_irqs = gic_irqs;
> 
>         gic_irqs -= hwirq_base; /* calculate # of irqs to allocate */
> @@ -1069,6 +1164,7 @@ gic_of_init(struct device_node *node, struct device_node *parent)
>  }
>  IRQCHIP_DECLARE(cortex_a15_gic, "arm,cortex-a15-gic", gic_of_init);
>  IRQCHIP_DECLARE(cortex_a9_gic, "arm,cortex-a9-gic", gic_of_init);
> +IRQCHIP_DECLARE(hip04_gic, "hisilicon,hip04-gic", gic_of_init);
>  IRQCHIP_DECLARE(msm_8660_qgic, "qcom,msm-8660-qgic", gic_of_init);
>  IRQCHIP_DECLARE(msm_qgic2, "qcom,msm-qgic2", gic_of_init);
> 
> --
> 1.9.1
> 
> 


-- 
Jazz is not dead. It just smells funny...

  reply	other threads:[~2014-05-15  9:34 UTC|newest]

Thread overview: 50+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-05-11  8:05 [PATCH v6 00/15] enable HiP04 SoC Haojian Zhuang
2014-05-11  8:05 ` [PATCH v6 01/15] ARM: debug: add HiP04 debug uart Haojian Zhuang
2014-05-11  8:05 ` [PATCH v6 02/15] irq: gic: use mask field in GICC_IAR Haojian Zhuang
2014-05-19  0:40   ` Jason Cooper
2014-05-11  8:05 ` [PATCH v6 03/15] irq: gic: support hip04 gic Haojian Zhuang
2014-05-15  9:34   ` Marc Zyngier [this message]
2014-05-15 11:14     ` Arnd Bergmann
2014-05-15 12:08       ` Christoffer Dall
2014-05-15 12:13         ` Arnd Bergmann
2014-05-15 12:16           ` Christoffer Dall
2014-05-20  3:24     ` Haojian Zhuang
2014-05-20  9:02       ` Marc Zyngier
2014-05-20  9:35         ` Haojian Zhuang
2014-05-20  9:42           ` Marc Zyngier
2014-05-19  2:05   ` Jason Cooper
2014-05-20  3:35     ` Haojian Zhuang
2014-05-11  8:06 ` [PATCH v6 04/15] ARM: mcpm: support 4 clusters Haojian Zhuang
2014-05-11  8:06 ` [PATCH v6 05/15] ARM: hisi: add ARCH_HISI Haojian Zhuang
2014-05-11  8:06 ` [PATCH v6 06/15] ARM: hisi: enable MCPM implementation Haojian Zhuang
2014-05-13  8:28   ` Dave Martin
2014-05-13  9:46     ` Haojian Zhuang
2014-05-13 11:44   ` [PATCH v7 " Haojian Zhuang
2014-05-13 19:43     ` Nicolas Pitre
2014-05-15  6:23       ` Haojian Zhuang
2014-05-15 20:01         ` Nicolas Pitre
2014-05-20  4:43           ` Haojian Zhuang
2014-05-21 10:02             ` Dave Martin
2014-05-21 13:52             ` Nicolas Pitre
2014-05-11  8:06 ` [PATCH v6 07/15] ARM: hisi: enable HiP04 Haojian Zhuang
2014-05-13 11:45   ` [PATCH v7 " Haojian Zhuang
2014-05-11  8:06 ` [PATCH v6 08/15] document: dt: add the binding on HiP04 Haojian Zhuang
2014-05-11  8:06 ` [PATCH v6 09/15] document: dt: add the binding on HiP04 clock Haojian Zhuang
2014-05-11  8:06 ` [PATCH v6 10/15] ARM: dts: append hip04 dts Haojian Zhuang
2014-05-11  8:06 ` [PATCH v6 11/15] ARM: config: append lpae configuration Haojian Zhuang
2014-05-11  8:06 ` [PATCH v6 12/15] ARM: config: append hip04_defconfig Haojian Zhuang
2014-05-11  8:06 ` [PATCH v6 13/15] ARM: config: select ARCH_HISI in hi3xxx_defconfig Haojian Zhuang
2014-05-11  8:06 ` [PATCH v6 14/15] ARM: hisi: enable erratum 798181 of A15 on HiP04 Haojian Zhuang
2014-05-11  8:06 ` [PATCH v6 15/15] virt: arm: support hip04 gic Haojian Zhuang
2014-05-15  9:42   ` Marc Zyngier
2014-05-15 13:09     ` Haojian Zhuang
2014-05-15 13:26       ` Marc Zyngier
2014-07-01  8:57         ` Haojian Zhuang
2014-05-20 10:51       ` Christoffer Dall
2014-05-14 18:37 ` [PATCH v6 00/15] enable HiP04 SoC Arnd Bergmann
2014-05-15  9:20   ` Haojian Zhuang
2014-05-15  9:31     ` Marc Zyngier
2014-05-16  5:07       ` Jason Cooper
2014-05-16  7:57         ` Marc Zyngier
2014-05-16 13:31           ` Jason Cooper
2014-05-16 19:09           ` Jason Cooper

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=53748A2B.9050304@arm.com \
    --to=marc.zyngier@arm.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.