147c147,148 < Kernel command line: root=/dev/sda2 --- > Kernel command line: root=/dev/sda2 acpi_osi="!Windows 2006" > ACPI: Deleted _OSI(Windows 2006) 174,175c175,176 < Detected 2094.823 MHz processor. < Calibrating delay loop (skipped), value calculated using timer frequency.. 4191.21 BogoMIPS (lpj=6982743) --- > Detected 2094.484 MHz processor. > Calibrating delay loop (skipped), value calculated using timer frequency.. 4190.50 BogoMIPS (lpj=6981613) 199c200 < Calibrating delay using timer specific routine.. 4191.04 BogoMIPS (lpj=6982470) --- > Calibrating delay using timer specific routine.. 4101.19 BogoMIPS (lpj=6832307) 208c209 < Total of 2 processors activated (8382.25 BogoMIPS). --- > Total of 2 processors activated (8291.70 BogoMIPS). 389c390 < type=2000 audit(1263063441.759:1): initialized --- > type=2000 audit(1263063607.762:1): initialized 455a457,466 > pata_acpi 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19 > pata_acpi 0000:00:1f.1: setting latency timer to 64 > pata_acpi 0000:00:1f.1: PCI INT A disabled > ata_piix 0000:00:1f.1: version 2.13 > ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19 > ata_piix 0000:00:1f.1: setting latency timer to 64 > scsi0 : ata_piix > scsi1 : ata_piix > ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14 > ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15 462,463d472 < scsi0 : ahci < scsi1 : ahci 465,468c474,482 < ata1: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404100 irq 28 < ata2: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404180 irq 28 < ata3: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404200 irq 28 < ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) --- > scsi3 : ahci > ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WW01, max UDMA/33 > scsi4 : ahci > ata3: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404100 irq 28 > ata4: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404180 irq 28 > ata5: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404200 irq 28 > ata1.00: configured for UDMA/33 > scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20N WW01 PQ: 0 ANSI: 5 > ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 470,491c484,495 < ata1.00: _GTF unexpected object type 0x1 < ata2: SATA link down (SStatus 0 SControl 300) < ata3: SATA link down (SStatus 0 SControl 300) < ata1.00: ATA-8: WDC WD2500BEVS-22UST0, 01.01A01, max UDMA/133 < ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA < ata1.00: _GTF unexpected object type 0x1 < ata1.00: configured for UDMA/133 < scsi 0:0:0:0: Direct-Access ATA WDC WD2500BEVS-2 01.0 PQ: 0 ANSI: 5 < pata_acpi 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19 < pata_acpi 0000:00:1f.1: setting latency timer to 64 < pata_acpi 0000:00:1f.1: PCI INT A disabled < ata_piix 0000:00:1f.1: version 2.13 < ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19 < ata_piix 0000:00:1f.1: setting latency timer to 64 < scsi3 : ata_piix < scsi4 : ata_piix < ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14 < ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15 < sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB) < sd 0:0:0:0: [sda] Write Protect is off < sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 < sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA --- > ata3.00: _GTF unexpected object type 0x1 > ata4: SATA link down (SStatus 0 SControl 300) > ata5: SATA link down (SStatus 0 SControl 300) > ata3.00: ATA-8: WDC WD2500BEVS-22UST0, 01.01A01, max UDMA/133 > ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA > ata3.00: _GTF unexpected object type 0x1 > ata3.00: configured for UDMA/133 > scsi 2:0:0:0: Direct-Access ATA WDC WD2500BEVS-2 01.0 PQ: 0 ANSI: 5 > sd 2:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB) > sd 2:0:0:0: [sda] Write Protect is off > sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 > sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 493,496c497 < sd 0:0:0:0: [sda] Attached SCSI disk < ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WW01, max UDMA/33 < ata4.00: configured for UDMA/33 < scsi 3:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20N WW01 PQ: 0 ANSI: 5 --- > sd 2:0:0:0: [sda] Attached SCSI disk 499c500 < sr 3:0:0:0: Attached scsi CD-ROM sr0 --- > sr 0:0:0:0: Attached scsi CD-ROM sr0 510d510 < Switching to clocksource hpet 513a514 > Switching to clocksource hpet 514a516,526 > sr 0:0:0:0: Attached scsi generic sg0 type 5 > sd 2:0:0:0: Attached scsi generic sg1 type 0 > ACPI: AC Adapter [AC0] (on-line) > thermal LNXTHERM:01: registered as thermal_zone0 > ACPI: Thermal Zone [THRM] (59 C) > iTCO_vendor_support: vendor-support=0 > ACPI: Battery Slot [BAT0] (battery present) > input: PC Speaker as /devices/platform/pcspkr/input/input7 > iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05 > iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060) > iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) 518,521c530,537 < sd 0:0:0:0: Attached scsi generic sg0 type 0 < sr 3:0:0:0: Attached scsi generic sg1 type 5 < ACPI: AC Adapter [AC0] (on-line) < ACPI: Battery Slot [BAT0] (battery present) --- > i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19 > ACPI: I/O resource 0000:00:1f.3 [0x1c20-0x1c3f] conflicts with ACPI region SMBI [0x1c20-0x1c2f] > ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver > r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded > r8169 0000:06:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 > r8169 0000:06:00.0: setting latency timer to 64 > r8169 0000:06:00.0: irq 29 for MSI/MSI-X > eth0: RTL8101e at 0xf9088000, 00:03:0d:7c:54:60, XID 14000000 IRQ 29 541d556 < uhci_hcd: USB Universal Host Controller Interface driver 545a561 > uhci_hcd: USB Universal Host Controller Interface driver 586,595d601 < thermal LNXTHERM:01: registered as thermal_zone0 < ACPI: Thermal Zone [THRM] (59 C) < i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19 < ACPI: I/O resource 0000:00:1f.3 [0x1c20-0x1c3f] conflicts with ACPI region SMBI [0x1c20-0x1c2f] < ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver < r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded < r8169 0000:06:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 < r8169 0000:06:00.0: setting latency timer to 64 < r8169 0000:06:00.0: irq 29 for MSI/MSI-X < eth0: RTL8101e at 0xf9070000, 00:03:0d:7c:54:60, XID 14000000 IRQ 29 598,602c604,608 < iTCO_vendor_support: vendor-support=0 < input: PC Speaker as /devices/platform/pcspkr/input/input7 < iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05 < iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060) < iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) --- > HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 > HDA Intel 0000:00:1b.0: setting latency timer to 64 > Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps: 0xa04713/0x200000 > input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8 > input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9 611,615d616 < Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps: 0xa04713/0x200000 < input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8 < HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 < HDA Intel 0000:00:1b.0: setting latency timer to 64 < input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9 629,640d629 < fuse init (API version 7.13) < wlan0: deauthenticating from 00:04:0e:60:53:78 by local choice (reason=3) < wlan0: direct probe to AP 00:04:0e:60:53:78 (try 1) < wlan0: direct probe responded < wlan0: authenticate with AP 00:04:0e:60:53:78 (try 1) < wlan0: authenticated < wlan0: associate with AP 00:04:0e:60:53:78 (try 1) < wlan0: RX AssocResp from 00:04:0e:60:53:78 (capab=0x411 status=0 aid=1) < wlan0: associated < ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready < padlock: VIA PadLock not detected. < wlan0: no IPv6 routers present