From: Jaehoon Chung <jh80.chung@samsung.com>
To: Addy Ke <addy.ke@rock-chips.com>,
robh+dt@kernel.org, pawel.moll@arm.com, mark.rutland@arm.com,
ijc+devicetree@hellion.org.uk, galak@codeaurora.org,
rdunlap@infradead.org, tgih.jun@samsung.com, chris@printf.net,
ulf.hansson@linaro.org, dinguyen@altera.com, heiko@sntech.de,
olof@lixom.net, dianders@chromium.org
Cc: devicetree@vger.kernel.org, linux-doc@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-mmc@vger.kernel.org,
zhenfu.fang@rock-chips.com, cf@rock-chips.com,
lintao@rock-chips.com, chenfen@rock-chips.com,
zyf@rock-chips.com, xjq@rock-chips.com, huangtao@rock-chips.com,
zyw@rock-chips.com, yzq@rock-chips.com, hj@rock-chips.com,
kever.yang@rock-chips.com, zhangqing@rock-chips.com,
hl@rock-chips.com
Subject: Re: [PATCH v2] mmc: dw_mmc: move rockchip related code to a separate file
Date: Tue, 19 Aug 2014 14:08:02 +0900 [thread overview]
Message-ID: <53F2DBB2.1000701@samsung.com> (raw)
In-Reply-To: <1408422974-22301-1-git-send-email-addy.ke@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Best Regards,
Jaehoon Chung
On 08/19/2014 01:36 PM, Addy Ke wrote:
> To support HS200 and UHS-1, we need add a big hunk of code,
> as shown in the following patches. So a separate file for
> rockchip SOCs is suitable.
>
> Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
> ---
> Changes in v2:
> - Kconfig: depend on ARCH_ROCKCHIP, suggested by Bartlomiej Zolnierkiewicz
> - Kconfig: depend on OF, suggested by Doug Anderson
> - Not change suspend/resume code, suggested by Doug Anderson
> - If pdev->dev.of_node is NULL, then return -ENODEV, suggested by Heiko Stübner
>
> drivers/mmc/host/Kconfig | 9 +++
> drivers/mmc/host/Makefile | 1 +
> drivers/mmc/host/dw_mmc-pltfm.c | 57 ----------------
> drivers/mmc/host/dw_mmc-rockchip.c | 136 +++++++++++++++++++++++++++++++++++++
> 4 files changed, 146 insertions(+), 57 deletions(-)
> create mode 100644 drivers/mmc/host/dw_mmc-rockchip.c
>
> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
> index a565254..f6095f6 100644
> --- a/drivers/mmc/host/Kconfig
> +++ b/drivers/mmc/host/Kconfig
> @@ -621,6 +621,15 @@ config MMC_DW_PCI
>
> If unsure, say N.
>
> +config MMC_DW_ROCKCHIP
> + tristate "Rockchip specific extensions for Synopsys DW Memory Card Interface"
> + depends on MMC_DW && ARCH_ROCKCHIP && OF
> + select MMC_DW_PLTFM
> + help
> + This selects support for Rockchip SoC specific extensions to the
> + Synopsys DesignWare Memory Card Interface driver. Select this option
> + for platforms based on RK3066, RK3188 and RK3288 SoC's.
> +
> config MMC_SH_MMCIF
> tristate "SuperH Internal MMCIF support"
> depends on MMC_BLOCK
> diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
> index 7f81ddf..5fce465 100644
> --- a/drivers/mmc/host/Makefile
> +++ b/drivers/mmc/host/Makefile
> @@ -45,6 +45,7 @@ obj-$(CONFIG_MMC_DW_PLTFM) += dw_mmc-pltfm.o
> obj-$(CONFIG_MMC_DW_EXYNOS) += dw_mmc-exynos.o
> obj-$(CONFIG_MMC_DW_K3) += dw_mmc-k3.o
> obj-$(CONFIG_MMC_DW_PCI) += dw_mmc-pci.o
> +obj-$(CONFIG_MMC_DW_ROCKCHIP) += dw_mmc-rockchip.o
> obj-$(CONFIG_MMC_SH_MMCIF) += sh_mmcif.o
> obj-$(CONFIG_MMC_JZ4740) += jz4740_mmc.o
> obj-$(CONFIG_MMC_VUB300) += vub300.o
> diff --git a/drivers/mmc/host/dw_mmc-pltfm.c b/drivers/mmc/host/dw_mmc-pltfm.c
> index b547f7a..0c56c41 100644
> --- a/drivers/mmc/host/dw_mmc-pltfm.c
> +++ b/drivers/mmc/host/dw_mmc-pltfm.c
> @@ -26,64 +26,11 @@
> #include "dw_mmc.h"
> #include "dw_mmc-pltfm.h"
>
> -#define RK3288_CLKGEN_DIV 2
> -
> static void dw_mci_pltfm_prepare_command(struct dw_mci *host, u32 *cmdr)
> {
> *cmdr |= SDMMC_CMD_USE_HOLD_REG;
> }
>
> -static int dw_mci_rk3288_setup_clock(struct dw_mci *host)
> -{
> - host->bus_hz /= RK3288_CLKGEN_DIV;
> -
> - return 0;
> -}
> -
> -static void dw_mci_rk3288_set_ios(struct dw_mci *host, struct mmc_ios *ios)
> -{
> - int ret;
> - unsigned int cclkin;
> - u32 bus_hz;
> -
> - /*
> - * cclkin: source clock of mmc controller.
> - * bus_hz: card interface clock generated by CLKGEN.
> - * bus_hz = cclkin / RK3288_CLKGEN_DIV;
> - * ios->clock = (div == 0) ? bus_hz : (bus_hz / (2 * div))
> - *
> - * Note: div can only be 0 or 1
> - * if DDR50 8bit mode(only emmc work in 8bit mode),
> - * div must be set 1
> - */
> - if ((ios->bus_width == MMC_BUS_WIDTH_8) &&
> - (ios->timing == MMC_TIMING_MMC_DDR52))
> - cclkin = 2 * ios->clock * RK3288_CLKGEN_DIV;
> - else
> - cclkin = ios->clock * RK3288_CLKGEN_DIV;
> -
> - ret = clk_set_rate(host->ciu_clk, cclkin);
> - if (ret)
> - dev_warn(host->dev, "failed to set rate %uHz\n", ios->clock);
> -
> - bus_hz = clk_get_rate(host->ciu_clk) / RK3288_CLKGEN_DIV;
> - if (bus_hz != host->bus_hz) {
> - host->bus_hz = bus_hz;
> - /* force dw_mci_setup_bus() */
> - host->current_speed = 0;
> - }
> -}
> -
> -static const struct dw_mci_drv_data rk2928_drv_data = {
> - .prepare_command = dw_mci_pltfm_prepare_command,
> -};
> -
> -static const struct dw_mci_drv_data rk3288_drv_data = {
> - .prepare_command = dw_mci_pltfm_prepare_command,
> - .set_ios = dw_mci_rk3288_set_ios,
> - .setup_clock = dw_mci_rk3288_setup_clock,
> -};
> -
> static const struct dw_mci_drv_data socfpga_drv_data = {
> .prepare_command = dw_mci_pltfm_prepare_command,
> };
> @@ -144,10 +91,6 @@ EXPORT_SYMBOL_GPL(dw_mci_pltfm_pmops);
>
> static const struct of_device_id dw_mci_pltfm_match[] = {
> { .compatible = "snps,dw-mshc", },
> - { .compatible = "rockchip,rk2928-dw-mshc",
> - .data = &rk2928_drv_data },
> - { .compatible = "rockchip,rk3288-dw-mshc",
> - .data = &rk3288_drv_data },
> { .compatible = "altr,socfpga-dw-mshc",
> .data = &socfpga_drv_data },
> {},
> diff --git a/drivers/mmc/host/dw_mmc-rockchip.c b/drivers/mmc/host/dw_mmc-rockchip.c
> new file mode 100644
> index 0000000..f0c2cb1
> --- /dev/null
> +++ b/drivers/mmc/host/dw_mmc-rockchip.c
> @@ -0,0 +1,136 @@
> +/*
> + * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/clk.h>
> +#include <linux/mmc/host.h>
> +#include <linux/mmc/dw_mmc.h>
> +#include <linux/of_address.h>
> +
> +#include "dw_mmc.h"
> +#include "dw_mmc-pltfm.h"
> +
> +#define RK3288_CLKGEN_DIV 2
> +
> +static void dw_mci_rockchip_prepare_command(struct dw_mci *host, u32 *cmdr)
> +{
> + *cmdr |= SDMMC_CMD_USE_HOLD_REG;
> +}
> +
> +static int dw_mci_rk3288_setup_clock(struct dw_mci *host)
> +{
> + host->bus_hz /= RK3288_CLKGEN_DIV;
> +
> + return 0;
> +}
> +
> +static void dw_mci_rk3288_set_ios(struct dw_mci *host, struct mmc_ios *ios)
> +{
> + int ret;
> + unsigned int cclkin;
> + u32 bus_hz;
> +
> + /*
> + * cclkin: source clock of mmc controller
> + * bus_hz: card interface clock generated by CLKGEN
> + * bus_hz = cclkin / RK3288_CLKGEN_DIV
> + * ios->clock = (div == 0) ? bus_hz : (bus_hz / (2 * div))
> + *
> + * Note: div can only be 0 or 1
> + * if DDR50 8bit mode(only emmc work in 8bit mode),
> + * div must be set 1
> + */
> + if (ios->bus_width == MMC_BUS_WIDTH_8 &&
> + ios->timing == MMC_TIMING_MMC_DDR52)
> + cclkin = 2 * ios->clock * RK3288_CLKGEN_DIV;
> + else
> + cclkin = ios->clock * RK3288_CLKGEN_DIV;
> +
> + ret = clk_set_rate(host->ciu_clk, cclkin);
> + if (ret)
> + dev_warn(host->dev, "failed to set rate %uHz\n", ios->clock);
> +
> + bus_hz = clk_get_rate(host->ciu_clk) / RK3288_CLKGEN_DIV;
> + if (bus_hz != host->bus_hz) {
> + host->bus_hz = bus_hz;
> + /* force dw_mci_setup_bus() */
> + host->current_speed = 0;
> + }
> +}
> +
> +static const struct dw_mci_drv_data rk2928_drv_data = {
> + .prepare_command = dw_mci_rockchip_prepare_command,
> +};
> +
> +static const struct dw_mci_drv_data rk3288_drv_data = {
> + .prepare_command = dw_mci_rockchip_prepare_command,
> + .set_ios = dw_mci_rk3288_set_ios,
> + .setup_clock = dw_mci_rk3288_setup_clock,
> +};
> +
> +static const struct of_device_id dw_mci_rockchip_match[] = {
> + { .compatible = "rockchip,rk2928-dw-mshc",
> + .data = &rk2928_drv_data },
> + { .compatible = "rockchip,rk3288-dw-mshc",
> + .data = &rk3288_drv_data },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, dw_mci_rockchip_match);
> +
> +static int dw_mci_rockchip_probe(struct platform_device *pdev)
> +{
> + const struct dw_mci_drv_data *drv_data;
> + const struct of_device_id *match;
> +
> + if (!pdev->dev.of_node)
> + return -ENODEV;
> +
> + match = of_match_node(dw_mci_rockchip_match, pdev->dev.of_node);
> + drv_data = match->data;
> +
> + return dw_mci_pltfm_register(pdev, drv_data);
> +}
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int dw_mci_rockchip_suspend(struct device *dev)
> +{
> + struct dw_mci *host = dev_get_drvdata(dev);
> +
> + return dw_mci_suspend(host);
> +}
> +
> +static int dw_mci_rockchip_resume(struct device *dev)
> +{
> + struct dw_mci *host = dev_get_drvdata(dev);
> +
> + return dw_mci_resume(host);
> +}
> +#endif /* CONFIG_PM_SLEEP */
> +
> +static SIMPLE_DEV_PM_OPS(dw_mci_rockchip_pmops,
> + dw_mci_rockchip_suspend,
> + dw_mci_rockchip_resume);
> +
> +static struct platform_driver dw_mci_rockchip_pltfm_driver = {
> + .probe = dw_mci_rockchip_probe,
> + .remove = __exit_p(dw_mci_pltfm_remove),
> + .driver = {
> + .name = "dwmmc_rockchip",
> + .of_match_table = dw_mci_rockchip_match,
> + .pm = &dw_mci_rockchip_pmops,
> + },
> +};
> +
> +module_platform_driver(dw_mci_rockchip_pltfm_driver);
> +
> +MODULE_AUTHOR("Addy Ke <addy.ke@rock-chips.com>");
> +MODULE_DESCRIPTION("Rockchip Specific DW-MSHC Driver Extension");
> +MODULE_ALIAS("platform:dwmmc-rockchip");
> +MODULE_LICENSE("GPL v2");
>
next prev parent reply other threads:[~2014-08-19 5:08 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-07-05 12:59 [PATCH] mmc: dw_mmc: add support for RK3288 addy ke
2014-07-05 12:59 ` addy ke
2014-07-07 2:07 ` Jaehoon Chung
2014-07-07 2:42 ` addy ke
2014-07-10 3:31 ` [PATCH v2] " Addy Ke
2014-07-29 4:52 ` Doug Anderson
2014-07-29 16:38 ` Doug Anderson
2014-07-31 6:01 ` [PATCH] " Addy Ke
2014-07-31 15:40 ` Doug Anderson
2014-08-12 12:17 ` Ulf Hansson
2014-08-07 8:47 ` Jaehoon Chung
[not found] ` <1406786498-3935-1-git-send-email-addy.ke-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
2014-08-14 8:01 ` [PATCH] mmc: dw_mmc: move rockchip related code to a separate file Addy Ke
2014-08-14 8:01 ` Addy Ke
2014-08-14 12:16 ` Bartlomiej Zolnierkiewicz
2014-08-14 17:09 ` Doug Anderson
2014-08-15 19:52 ` Heiko Stübner
2014-08-19 4:36 ` [PATCH v2] " Addy Ke
2014-08-19 5:08 ` Jaehoon Chung [this message]
2014-08-19 17:28 ` Doug Anderson
2014-08-19 17:28 ` Doug Anderson
2014-08-29 11:05 ` Ulf Hansson
2014-08-29 11:05 ` Ulf Hansson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=53F2DBB2.1000701@samsung.com \
--to=jh80.chung@samsung.com \
--cc=addy.ke@rock-chips.com \
--cc=cf@rock-chips.com \
--cc=chenfen@rock-chips.com \
--cc=chris@printf.net \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=dinguyen@altera.com \
--cc=galak@codeaurora.org \
--cc=heiko@sntech.de \
--cc=hj@rock-chips.com \
--cc=hl@rock-chips.com \
--cc=huangtao@rock-chips.com \
--cc=ijc+devicetree@hellion.org.uk \
--cc=kever.yang@rock-chips.com \
--cc=lintao@rock-chips.com \
--cc=linux-doc@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=olof@lixom.net \
--cc=pawel.moll@arm.com \
--cc=rdunlap@infradead.org \
--cc=robh+dt@kernel.org \
--cc=tgih.jun@samsung.com \
--cc=ulf.hansson@linaro.org \
--cc=xjq@rock-chips.com \
--cc=yzq@rock-chips.com \
--cc=zhangqing@rock-chips.com \
--cc=zhenfu.fang@rock-chips.com \
--cc=zyf@rock-chips.com \
--cc=zyw@rock-chips.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.