From: "P. Gautschi" <linuxlist@gautschi.net>
To: linux-raid <linux-raid@vger.kernel.org>
Subject: Disks never stop spinning
Date: Mon, 10 Nov 2014 19:44:24 +0100 [thread overview]
Message-ID: <54610788.6060103@gautschi.net> (raw)
[-- Attachment #1: Type: text/plain, Size: 762 bytes --]
I've got an array (on kubuntu 14.10) with 5 WD-RED drives and would like
them to stop rotating when there is no access for 10 minutes.
I used hdparm -S 120 for all of them but they keep on running.
I stopped the arrays but this does not help either. The problem might therefor
be unrelated to mdadm. However stopping idle disks on notebooks and desktops
too should be common and I would assume that the general mechanisms are
working. Also for NAS stopping disks should be widely used.
Any ideas why the disks never enter standby or sleep state or how to solve
the problem?
Patrick
PS: I found a hint mentioning SMART tests running in the background could cause
this problem. As far as I understand the output of smartctl, no tests are running
on my disks.
[-- Attachment #2: hdinfo.txt --]
[-- Type: text/plain, Size: 4000 bytes --]
/dev/sdf:
Model=WDC WD60EFRX-68MYMN1, FwRev=82.00A82, SerialNo=WD-WX11D4415118
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=unknown, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=11721045168
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no WriteCache=enabled
Drive conforms to: Reserved: ATA/ATAPI-1,2,3,4,5,6,7
* signifies the current active mode
ATA device, with non-removable media
Model Number: WDC WD60EFRX-68MYMN1
Serial Number: WD-WX11D4415118
Firmware Revision: 82.00A82
Transport: Serial, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
Used: unknown (minor revision code 0x001f)
Supported: 9 8 7 6 5
Likely used: 9
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors:11721045168
Logical Sector size: 512 bytes
Physical Sector size: 4096 bytes
Logical Sector-0 offset: 0 bytes
device size with M = 1024*1024: 5723166 MBytes
device size with M = 1000*1000: 6001175 MBytes (6001 GB)
cache/buffer size = unknown
Nominal Media Rotation Rate: 5700
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
Power-Up In Standby feature set
* SET_FEATURES required to spinup after power up
SET_MAX security extension
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
Media Card Pass-Through
* General Purpose Logging feature set
* 64-bit World wide name
* URG for READ_STREAM[_DMA]_EXT
* URG for WRITE_STREAM[_DMA]_EXT
* IDLE_IMMEDIATE with UNLOAD
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Gen3 signaling speed (6.0Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
* Idle-Unload when NCQ is active
* NCQ priority information
* READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
* DMA Setup Auto-Activate optimization
* Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Write Same (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12] (vendor specific)
unknown 206[13] (vendor specific)
* DOWNLOAD MICROCODE DMA command
* WRITE BUFFER DMA command
* READ BUFFER DMA command
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
supported: enhanced erase
Logical Unit WWN Device Identifier: 50014ee0ae896953
NAA : 5
IEEE OUI : 0014ee
Unique ID : 0ae896953
Checksum: correct
[-- Attachment #3: smart.txt --]
[-- Type: text/plain, Size: 10015 bytes --]
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.16.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: WDC WD60EFRX-68MYMN1
Serial Number: WD-WX11D4415118
LU WWN Device Id: 5 0014ee 0ae896953
Firmware Version: 82.00A82
User Capacity: 6'001'175'126'016 bytes [6.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5700 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Nov 10 18:20:06 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 5204) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 705) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 201 201 021 - 8925
4 Start_Stop_Count -O--CK 100 100 000 - 11
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 100 100 000 - 16
10 Spin_Retry_Count -O--CK 100 253 000 - 0
11 Calibration_Retry_Count -O--CK 100 253 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 6
192 Power-Off_Retract_Count -O--CK 200 200 000 - 3
193 Load_Cycle_Count -O--CK 200 200 000 - 11
194 Temperature_Celsius -O---K 121 113 000 - 31
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb6 GPL,SL VS 1 Device vendor specific log
0xb7 GPL,SL VS 40 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
No Errors Logged
SMART Error Log Version: 1
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 31 Celsius
Power Cycle Min/Max Temperature: 28/31 Celsius
Lifetime Min/Max Temperature: 20/39 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (50)
Index Estimated Time Temperature Celsius
51 2014-11-10 10:23 35 ****************
... ..(125 skipped). .. ****************
177 2014-11-10 12:29 35 ****************
178 2014-11-10 12:30 34 ***************
... ..(247 skipped). .. ***************
426 2014-11-10 16:38 34 ***************
427 2014-11-10 16:39 ? -
428 2014-11-10 16:40 34 ***************
... ..( 2 skipped). .. ***************
431 2014-11-10 16:43 34 ***************
432 2014-11-10 16:44 33 **************
... ..( 6 skipped). .. **************
439 2014-11-10 16:51 33 **************
440 2014-11-10 16:52 ? -
441 2014-11-10 16:53 20 *
... ..( 2 skipped). .. *
444 2014-11-10 16:56 20 *
445 2014-11-10 16:57 21 **
446 2014-11-10 16:58 ? -
447 2014-11-10 16:59 21 **
448 2014-11-10 17:00 22 ***
449 2014-11-10 17:01 22 ***
450 2014-11-10 17:02 23 ****
451 2014-11-10 17:03 23 ****
452 2014-11-10 17:04 23 ****
453 2014-11-10 17:05 24 *****
454 2014-11-10 17:06 24 *****
455 2014-11-10 17:07 24 *****
456 2014-11-10 17:08 ? -
457 2014-11-10 17:09 25 ******
458 2014-11-10 17:10 25 ******
459 2014-11-10 17:11 25 ******
460 2014-11-10 17:12 26 *******
... ..( 4 skipped). .. *******
465 2014-11-10 17:17 26 *******
466 2014-11-10 17:18 27 ********
... ..( 6 skipped). .. ********
473 2014-11-10 17:25 27 ********
474 2014-11-10 17:26 ? -
475 2014-11-10 17:27 28 *********
... ..( 3 skipped). .. *********
1 2014-11-10 17:31 28 *********
2 2014-11-10 17:32 29 **********
... ..( 3 skipped). .. **********
6 2014-11-10 17:36 29 **********
7 2014-11-10 17:37 30 ***********
... ..( 3 skipped). .. ***********
11 2014-11-10 17:41 30 ***********
12 2014-11-10 17:42 31 ************
... ..( 37 skipped). .. ************
50 2014-11-10 18:20 31 ************
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
Device Statistics (GP Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 3 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 3231 Vendor specific
next reply other threads:[~2014-11-10 18:44 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-11-10 18:44 P. Gautschi [this message]
2014-11-13 14:05 ` Disks never stop spinning Peter Grandi
2014-11-14 3:05 ` Patrick Gautschi
2014-11-14 4:11 ` Brad Campbell
2014-12-04 19:33 ` Phillip Susi
2014-12-06 15:16 ` P. Gautschi
2014-12-08 20:38 ` Phillip Susi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=54610788.6060103@gautschi.net \
--to=linuxlist@gautschi.net \
--cc=linux-raid@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.