From: Przemek Kitszel <przemyslaw.kitszel@intel.com>
To: Jacob Keller <jacob.e.keller@intel.com>,
Intel Wired LAN <intel-wired-lan@lists.osuosl.org>
Cc: Karol Kolacinski <karol.kolacinski@intel.com>,
Anthony Nguyen <anthony.l.nguyen@intel.com>
Subject: Re: [Intel-wired-lan] [PATCH iwl-next 3/4] ice: check the netlist before enabling ICE_F_SMA_CTRL
Date: Wed, 16 Aug 2023 12:54:25 +0200 [thread overview]
Message-ID: <546e415b-d34c-f4e1-a8f5-e3c13bf03cdf@intel.com> (raw)
In-Reply-To: <20230815223551.1238091-4-jacob.e.keller@intel.com>
On 8/16/23 00:35, Jacob Keller wrote:
> Currently, the ice driver unconditionally enables ICE_F_SMA_CTRL for all
> E810-T based devices. In some cases, the SMA control access is not
> available in the netlist firmware component. In such a case, the driver
> will fail to setup the SMA pins. When this happens, the driver prints
> "Failed to configure E810-T SMA pin control" and forcibly disables all PTP
> pin configuration support.
>
> This results in failure to use even the fixed pin capabilities of standard
> E810 devices, resulting in reduced functionality.
>
> To avoid this, check the netlist for the SMA control module before enabling
> the ICE_F_SMA_CTRL feature. If the netlist lacks this module, then the
> feature will not be enabled. In this case, the driver flow for enabling
> periodic outputs and external timestamps will fall back to the standard
> fixed pin configuration.
>
> This allows supporting the software defined pins on a wider array of
> platforms.
>
> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Overall it's a nice series!
> ---
> .../net/ethernet/intel/ice/ice_adminq_cmd.h | 6 ++-
> drivers/net/ethernet/intel/ice/ice_common.c | 46 +++++++++++++++++++
> drivers/net/ethernet/intel/ice/ice_common.h | 3 ++
> drivers/net/ethernet/intel/ice/ice_lib.c | 3 +-
> drivers/net/ethernet/intel/ice/ice_ptp_hw.c | 16 +++++++
> drivers/net/ethernet/intel/ice/ice_ptp_hw.h | 1 +
> 6 files changed, 72 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/net/ethernet/intel/ice/ice_adminq_cmd.h b/drivers/net/ethernet/intel/ice/ice_adminq_cmd.h
> index 90616750e779..82c4daf0a825 100644
> --- a/drivers/net/ethernet/intel/ice/ice_adminq_cmd.h
> +++ b/drivers/net/ethernet/intel/ice/ice_adminq_cmd.h
> @@ -1367,6 +1367,7 @@ struct ice_aqc_link_topo_params {
> #define ICE_AQC_LINK_TOPO_NODE_TYPE_CAGE 6
> #define ICE_AQC_LINK_TOPO_NODE_TYPE_MEZZ 7
> #define ICE_AQC_LINK_TOPO_NODE_TYPE_ID_EEPROM 8
> +#define ICE_AQC_LINK_TOPO_NODE_TYPE_CLK_MUX 10
> #define ICE_AQC_LINK_TOPO_NODE_CTX_S 4
> #define ICE_AQC_LINK_TOPO_NODE_CTX_M \
> (0xF << ICE_AQC_LINK_TOPO_NODE_CTX_S)
> @@ -1403,8 +1404,9 @@ struct ice_aqc_link_topo_addr {
> struct ice_aqc_get_link_topo {
> struct ice_aqc_link_topo_addr addr;
> u8 node_part_num;
> -#define ICE_AQC_GET_LINK_TOPO_NODE_NR_PCA9575 0x21
> -#define ICE_AQC_GET_LINK_TOPO_NODE_NR_C827 0x31
> +#define ICE_AQC_GET_LINK_TOPO_NODE_NR_PCA9575 0x21
> +#define ICE_AQC_GET_LINK_TOPO_NODE_NR_C827 0x31
> +#define ICE_ACQ_GET_LINK_TOPO_NODE_NR_GEN_CLK_MUX 0x47
> u8 rsvd[9];
> };
>
> diff --git a/drivers/net/ethernet/intel/ice/ice_common.c b/drivers/net/ethernet/intel/ice/ice_common.c
> index 2652e4f5c4a2..9eeda3f5aa75 100644
> --- a/drivers/net/ethernet/intel/ice/ice_common.c
> +++ b/drivers/net/ethernet/intel/ice/ice_common.c
> @@ -2503,6 +2503,52 @@ bool ice_is_pf_c827(struct ice_hw *hw)
> return false;
> }
>
> +#define MAX_NETLIST_SIZE 10
> +/**
> + * ice_find_netlist_node
> + * @hw: pointer to the hw struct
> + * @node_type_ctx: type of netlist node to look for
> + * @node_part_number: node part number to look for
> + * @node_handle: output parameter if node found - optional
> + *
> + * Find and return the node handle for a given node type and part number in the
> + * netlist. When found 0 is returned, -ENOENT otherwise. If
> + * node_handle provided, it would be set to found node handle.
> + */
> +int
> +ice_find_netlist_node(struct ice_hw *hw, u8 node_type_ctx, u8 node_part_number,
> + u16 *node_handle)
> +{
> + struct ice_aqc_get_link_topo cmd;
> + u8 rec_node_part_number;
> + u16 rec_node_handle;
I see that you are using separate variable to 'do not touch'
@node_handle param if it does not need to be updated.
But perhaps you could consider to just pass @node_handle in place of
@rec_node_handle below, and have less code?
I do not see any non-null usage of the field anyway.
(rationale: our code is so self-similar that I needed to check wheater
you are basing-of recent changes by Jan&Karol or re-doing them ;)
answer: we are fine here :)).
> + u8 idx;
> +
> + for (idx = 0; idx < MAX_NETLIST_SIZE; idx++) {
> + int status;
> +
> + memset(&cmd, 0, sizeof(cmd));
> +
> + cmd.addr.topo_params.node_type_ctx =
> + (node_type_ctx << ICE_AQC_LINK_TOPO_NODE_TYPE_S);
I would FIELD_PREP() here
and perhaps convert @cmd scope to inside the loop, that would enable = {
.addr.topo_params = { ... } } declaration
> + cmd.addr.topo_params.index = idx;
> +
> + status = ice_aq_get_netlist_node(hw, &cmd,
> + &rec_node_part_number,
> + &rec_node_handle);
> + if (status)
> + return status;
> +
> + if (rec_node_part_number == node_part_number) {
> + if (node_handle)
> + *node_handle = rec_node_handle;
> + return 0;
> + }
> + }
> +
> + return -ENOENT;
> +}
> +
> /**
> * ice_aq_list_caps - query function/device capabilities
> * @hw: pointer to the HW struct
> diff --git a/drivers/net/ethernet/intel/ice/ice_common.h b/drivers/net/ethernet/intel/ice/ice_common.h
> index 2250a9c5f61e..f7178a5686a5 100644
> --- a/drivers/net/ethernet/intel/ice/ice_common.h
> +++ b/drivers/net/ethernet/intel/ice/ice_common.h
> @@ -94,6 +94,9 @@ ice_aq_get_phy_caps(struct ice_port_info *pi, bool qual_mods, u8 report_mode,
> struct ice_sq_cd *cd);
> bool ice_is_pf_c827(struct ice_hw *hw);
> int
> +ice_find_netlist_node(struct ice_hw *hw, u8 node_type_ctx, u8 node_part_number,
> + u16 *node_handle);
> +int
> ice_aq_list_caps(struct ice_hw *hw, void *buf, u16 buf_size, u32 *cap_count,
> enum ice_adminq_opc opc, struct ice_sq_cd *cd);
> int
> diff --git a/drivers/net/ethernet/intel/ice/ice_lib.c b/drivers/net/ethernet/intel/ice/ice_lib.c
> index f29ff54383b5..4ac8998cb964 100644
> --- a/drivers/net/ethernet/intel/ice/ice_lib.c
> +++ b/drivers/net/ethernet/intel/ice/ice_lib.c
> @@ -3989,8 +3989,9 @@ void ice_init_feature_support(struct ice_pf *pf)
> /* If we don't own the timer - don't enable other caps */
> if (!ice_pf_src_tmr_owned(pf))
> break;
> - if (ice_is_e810t(&pf->hw)) {
> + if (ice_is_clock_mux_present_e810t(&pf->hw))
> ice_set_feature_support(pf, ICE_F_SMA_CTRL);
> + if (ice_is_e810t(&pf->hw)) {
> if (ice_gnss_is_gps_present(&pf->hw))
> ice_set_feature_support(pf, ICE_F_GNSS);
> }
> diff --git a/drivers/net/ethernet/intel/ice/ice_ptp_hw.c b/drivers/net/ethernet/intel/ice/ice_ptp_hw.c
> index fd19afaf9c85..bd3f32bfbc78 100644
> --- a/drivers/net/ethernet/intel/ice/ice_ptp_hw.c
> +++ b/drivers/net/ethernet/intel/ice/ice_ptp_hw.c
> @@ -3018,6 +3018,22 @@ ice_get_pca9575_handle(struct ice_hw *hw, u16 *pca9575_handle)
> return 0;
> }
>
> +/**
> + * ice_is_clock_mux_present_e810t
> + * @hw: pointer to the hw struct
> + *
> + * Check if the Clock Multiplexer device is present in the netlist
> + */
> +bool ice_is_clock_mux_present_e810t(struct ice_hw *hw)
> +{
> + if (ice_find_netlist_node(hw, ICE_AQC_LINK_TOPO_NODE_TYPE_CLK_MUX,
> + ICE_ACQ_GET_LINK_TOPO_NODE_NR_GEN_CLK_MUX,
> + NULL))
> + return false;
> +
> + return true;
> +}
> +
> /**
> * ice_read_sma_ctrl_e810t
> * @hw: pointer to the hw struct
> diff --git a/drivers/net/ethernet/intel/ice/ice_ptp_hw.h b/drivers/net/ethernet/intel/ice/ice_ptp_hw.h
> index 4e3c1382c477..3768e7a01920 100644
> --- a/drivers/net/ethernet/intel/ice/ice_ptp_hw.h
> +++ b/drivers/net/ethernet/intel/ice/ice_ptp_hw.h
> @@ -195,6 +195,7 @@ int ice_phy_cfg_tx_offset_e822(struct ice_hw *hw, u8 port);
> int ice_phy_cfg_rx_offset_e822(struct ice_hw *hw, u8 port);
>
> /* E810 family functions */
> +bool ice_is_clock_mux_present_e810t(struct ice_hw *hw);
> int ice_ptp_init_phy_e810(struct ice_hw *hw);
> int ice_read_sma_ctrl_e810t(struct ice_hw *hw, u8 *data);
> int ice_write_sma_ctrl_e810t(struct ice_hw *hw, u8 data);
_______________________________________________
Intel-wired-lan mailing list
Intel-wired-lan@osuosl.org
https://lists.osuosl.org/mailman/listinfo/intel-wired-lan
next prev parent reply other threads:[~2023-08-16 10:54 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-08-15 22:35 [Intel-wired-lan] [PATCH iwl-next 0/4] ice: refactor PTP feature flags Jacob Keller
2023-08-15 22:35 ` [Intel-wired-lan] [PATCH iwl-next 1/4] ice: remove ICE_F_PTP_EXTTS feature flag Jacob Keller
2023-08-15 22:35 ` [Intel-wired-lan] [PATCH iwl-next 2/4] ice: don't enable PTP related capabilities on non-owner PFs Jacob Keller
2023-08-15 22:35 ` [Intel-wired-lan] [PATCH iwl-next 3/4] ice: check the netlist before enabling ICE_F_SMA_CTRL Jacob Keller
2023-08-16 0:31 ` Jacob Keller
2023-08-16 1:44 ` kernel test robot
2023-08-16 1:44 ` kernel test robot
2023-08-16 10:54 ` Przemek Kitszel [this message]
2023-08-16 22:11 ` Keller, Jacob E
2023-08-16 23:33 ` Jacob Keller
2023-08-16 23:34 ` Jacob Keller
2023-08-15 22:35 ` [Intel-wired-lan] [PATCH iwl-next 4/4] ice: check netlist before enabling ICE_F_GNSS Jacob Keller
2023-08-16 0:32 ` Jacob Keller
2023-08-16 2:47 ` kernel test robot
2023-08-16 2:47 ` kernel test robot
2023-08-15 22:35 ` [Intel-wired-lan] [PATCH iwl-next 0/4] ice: refactor PTP feature flags Jacob Keller
2023-08-15 22:35 ` [Intel-wired-lan] [PATCH iwl-next 1/4] ice: remove ICE_F_PTP_EXTTS feature flag Jacob Keller
2023-08-15 22:35 ` [Intel-wired-lan] [PATCH iwl-next 2/4] ice: don't enable PTP related capabilities on non-owner PFs Jacob Keller
2023-08-15 22:35 ` [Intel-wired-lan] [PATCH iwl-next 3/4] ice: check the netlist before enabling ICE_F_SMA_CTRL Jacob Keller
2023-08-15 22:35 ` [Intel-wired-lan] [PATCH iwl-next 4/4] ice: check netlist before enabling ICE_F_GNSS Jacob Keller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=546e415b-d34c-f4e1-a8f5-e3c13bf03cdf@intel.com \
--to=przemyslaw.kitszel@intel.com \
--cc=anthony.l.nguyen@intel.com \
--cc=intel-wired-lan@lists.osuosl.org \
--cc=jacob.e.keller@intel.com \
--cc=karol.kolacinski@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.