From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: from mail102.csoft.net ([96.47.74.245]:54799 "EHLO mail102.csoft.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1754331AbaLKPLy (ORCPT ); Thu, 11 Dec 2014 10:11:54 -0500 Message-ID: <5489B215.20707@fid4.com> Date: Thu, 11 Dec 2014 10:02:45 -0500 From: "Michael C. Cambria" MIME-Version: 1.0 Subject: Re: [ANNOUNCE] wpan-tools 0.3 released References: <20141207150814.GA9532@omega> <548487CF.4060009@fid4.com> <20141207171311.GB9532@omega> <20141207171903.GC9532@omega> <5484C900.2020402@fid4.com> <20141207215452.GB20260@omega> In-Reply-To: <20141207215452.GB20260@omega> Content-Type: text/plain; charset=utf-8; format=flowed Content-Transfer-Encoding: 7bit Sender: linux-wpan-owner@vger.kernel.org List-ID: To: Alexander Aring Cc: linux-wpan@vger.kernel.org On 12/07/2014 04:54 PM, Alexander Aring wrote: > > ok. Read introductions at [0]. Begin at "Bring up 6LoWPAN" section. > For the at86rf230 you should have default a wpan0 interface. If you > use wpan-tools simple type "iwpan" and read the help for setting > address information. I think for at86rf230 you need to set the panid > only, phy settings should be transceiver defaults and short address > isn't supported for 6LoWPAN (except broadcast address, of course). The > documentation is a little bit outdated currently. [deleted] > > If you need help simple ask here or for better fast live supporting > you can contact me via IRC #linux-wpan on irc.freenode.net. Ping > between two nodes should be an easy setup. - Alex [0] > http://linux-zigbee.sourceforge.net/cgi-bin/trac.cgi/wiki/GettingStarted-0.2 > -- To unsubscribe from this list: send the line "unsubscribe > linux-wpan" in the body of a message to majordomo@vger.kernel.org More > majordomo info at http://vger.kernel.org/majordomo-info.html I'm using bluetooth-next, and it boots and seems to find the openlabs.co adapter just fine. GettingStarted-0.2 describes the "iz" command. I don't have "iz". I built/installed on the Pi itself, downloaded from http://wpan.cakelab.org/releases/. I do see an iwpan command installed (see below).Are there more user tools or do we just substitute iz with iwpan? Once an IPv6 address is assigned to wpan0, should I be able to ping wpan0 from an IPv6 address on a different box? I ask because I only have one Pi at the moment and can't test radio to radio. pi@raspberrypi:~$ iwpan list wpan_phy wpan-phy0 supported channels: page 0: 11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26 current_page: 0 current_channel: 13 cca_mode: 0 tx_power: 0 pi@raspberrypi:~$ pi@raspberrypi:~$ pi@raspberrypi:~$ pi@raspberrypi:~$ pi@raspberrypi:~$ ifconfig eth0 Link encap:Ethernet HWaddr 7a:93:66:29:55:e3 inet addr:192.168.1.171 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7893:66ff:fe29:55e3/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:140 errors:2 dropped:0 overruns:0 frame:0 TX packets:64 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10011 (9.7 KiB) TX bytes:6536 (6.3 KiB) [deleted] wpan0 Link encap:UNSPEC HWaddr 26-8E-9A-10-24-7B-3A-81-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING NOARP MTU:127 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:300 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) pi@raspberrypi:~$