All of lore.kernel.org
 help / color / mirror / Atom feed
From: Stanimir Varbanov <svarbanov@mm-sol.com>
To: Lina Iyer <lina.iyer@linaro.org>
Cc: Gilad Avidov <gavidov@codeaurora.org>,
	sdharia@codeaurora.org, mlocke@codeaurora.org,
	linux-arm-msm@vger.kernel.org, gregkh@linuxfoundation.org,
	linux-kernel@vger.kernel.org, iivanov@mm-sol.com,
	galak@codeaurora.org, agross@codeaurora.org
Subject: Re: [PATCH V2 2/2] spmi: pmic_arb: add support for hw version 2
Date: Wed, 04 Feb 2015 16:36:12 +0200	[thread overview]
Message-ID: <54D22E5C.1050204@mm-sol.com> (raw)
In-Reply-To: <20150203212150.GE4855@linaro.org>

Hi Lina, Gilad

On 02/03/2015 11:21 PM, Lina Iyer wrote:
> On Tue, Feb 03 2015 at 02:59 -0700, Stanimir Varbanov wrote:
>> Hi Gilad,
>>
>> Thanks for the patch.
>>
>> On 01/31/2015 02:46 AM, Gilad Avidov wrote:
>>> Qualcomm PMIC Arbiter version-2 changes from version-1 are:
>>>
>>> - Some different register offsets.
>>> - New channel register space, one per PMIC peripheral (ppid).
>>>   All tx traffic uses these channels.
>>> - New observer register space. All rx trafic uses this space.
>>> - Different command format for spmi command registers.
>>>
>>> Signed-off-by: Gilad Avidov <gavidov@codeaurora.org>
>>> Acked-by: Sagar Dharia <sdharia@codeaurora.org>
>>> ---
>>>  .../bindings/spmi/qcom,spmi-pmic-arb.txt           |   6 +-
>>>  drivers/spmi/spmi-pmic-arb.c                       | 310
>>> +++++++++++++++++----
>>>  2 files changed, 260 insertions(+), 56 deletions(-)
>>>
>>> diff --git
>>> a/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
>>> b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
>>> index 715d099..e16b9b5 100644
>>> --- a/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
>>> +++ b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
>>> @@ -1,6 +1,6 @@
>>>  Qualcomm SPMI Controller (PMIC Arbiter)
>>>
>>> -The SPMI PMIC Arbiter is found on the Snapdragon 800 Series.  It is
>>> an SPMI
>>> +The SPMI PMIC Arbiter is found on Snapdragon chipsets.  It is an SPMI
>>>  controller with wrapping arbitration logic to allow for multiple
>>> on-chip
>>>  devices to control a single SPMI master.
>>>
>>> @@ -19,6 +19,10 @@ Required properties:
>>>       "core" - core registers
>>>       "intr" - interrupt controller registers
>>>       "cnfg" - configuration registers
>>> +   Registers used only for V2 PMIC Arbiter:
>>> +     "chnls"  - tx-channel per virtual slave registers.
>>> +     "obsrvr" - rx-channel (called observer) per virtual slave
>>> registers.
>>> +
>>>  - reg : address + size pairs describing the PMIC arb register sets;
>>> order must
>>>          correspond with the order of entries in reg-names
>>>  - #address-cells : must be set to 2
>>> diff --git a/drivers/spmi/spmi-pmic-arb.c b/drivers/spmi/spmi-pmic-arb.c
>>> index 20559ab..818b2cf 100644
>>> --- a/drivers/spmi/spmi-pmic-arb.c
>>> +++ b/drivers/spmi/spmi-pmic-arb.c
>>> @@ -1,4 +1,4 @@
>>> -/* Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
>>> +/* Copyright (c) 2012-2015, The Linux Foundation. All rights reserved.
>>
>> run checkpatch, there are tons of errors like white spaces and DOS line
>> ending.
> 
> I dont see any DOS line endings with these patches. I believe the
> checkpatch warnings also are false positives.
> 

My fault, I wrongly saved the patch using Thinderbird. But the above
obviously breaks multiline comments coding style rules.

-- 
regards,
Stan

      reply	other threads:[~2015-02-04 14:36 UTC|newest]

Thread overview: 10+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-01-31  0:46 [PATCH V2 0/2] add support for pmic_arb v2 and correct framework Gilad Avidov
2015-01-31  0:46 ` [PATCH V2 1/2] spmi: remove wakeup command before slave probe Gilad Avidov
2015-02-03  9:36   ` Stanimir Varbanov
2015-02-04  1:17     ` Gilad Avidov
2015-01-31  0:46 ` [PATCH V2 2/2] spmi: pmic_arb: add support for hw version 2 Gilad Avidov
2015-02-03  9:59   ` Stanimir Varbanov
2015-02-03 16:59     ` Gilad Avidov
2015-02-03 17:14       ` Stanimir Varbanov
2015-02-03 21:21     ` Lina Iyer
2015-02-04 14:36       ` Stanimir Varbanov [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=54D22E5C.1050204@mm-sol.com \
    --to=svarbanov@mm-sol.com \
    --cc=agross@codeaurora.org \
    --cc=galak@codeaurora.org \
    --cc=gavidov@codeaurora.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=iivanov@mm-sol.com \
    --cc=lina.iyer@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mlocke@codeaurora.org \
    --cc=sdharia@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.