From: Camm Maguire <camm@enhanced.com>
To: linux-kernel@vger.kernel.org
Subject: 2.2.18 IDE tape problem, with ide-scsi
Date: 27 Feb 2001 11:06:34 -0500 [thread overview]
Message-ID: <54u25g3yb9.fsf_-_@intech19.enhanced.com> (raw)
In-Reply-To: jerry's message of "Mon, 26 Feb 2001 15:06:13 -0500"
Greetings! Two ide tapes, both on second ide channel, both using
ide-scsi. One works perfectly, the other basically works, but gives
errors, and occasionally doesn't write full 32k blocks to tape,
causing amanda errors.
Feb 25 06:14:22 intech9 kernel: ALI15X3: IDE controller on PCI bus 00 dev 78
Feb 25 06:14:22 intech9 kernel: ALI15X3: not 100%% native mode: will probe irqs later
Feb 25 06:14:22 intech9 kernel: ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:DMA
Feb 25 06:14:22 intech9 kernel:
Feb 25 06:14:22 intech9 kernel: ************************************
Feb 25 06:14:22 intech9 kernel: * ALi IDE driver (1.0 beta3) *
Feb 25 06:14:22 intech9 kernel: * Chip Revision is C1 *
Feb 25 06:14:22 intech9 kernel: * Maximum capability is - UDMA 33 *
Feb 25 06:14:22 intech9 kernel: ************************************
Feb 25 06:14:22 intech9 kernel:
Feb 25 06:14:22 intech9 kernel: ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:pio
Feb 25 06:14:22 intech9 kernel: hda: FUJITSU MPE3064AT, ATA DISK drive
Feb 25 06:14:22 intech9 kernel: hdb: ST32140A, ATA DISK drive
Feb 25 06:14:22 intech9 kernel: hdc: CONNER CTT8000-A, ATAPI TAPE drive
Feb 25 06:14:22 intech9 kernel: hdd: HP COLORADO 14GB, ATAPI TAPE drive
Feb 25 06:14:22 intech9 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Feb 25 06:14:22 intech9 kernel: ide1 at 0x170-0x177,0x376 on irq 15
Feb 25 06:14:22 intech9 kernel: ALI15X3: Ultra DMA enabled
Feb 25 06:14:22 intech9 kernel: hda: FUJITSU MPE3064AT, 6187MB w/512kB Cache, CHS=788/255/63, (U)DMA
Feb 25 06:14:22 intech9 kernel: ALI15X3: MultiWord DMA enabled
Feb 25 06:14:22 intech9 kernel: hdb: ST32140A, 2015MB w/128kB Cache, CHS=4095/16/63, DMA
Feb 25 06:14:22 intech9 kernel: hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
Feb 25 06:14:22 intech9 kernel: hdb: hdb1 hdb2
The Conner gives the problem:
Feb 27 06:23:16 intech9 kernel: st0: Error with sense data: [valid=0] Info fld=0x0, Current st09:00: sns = 70 5
Feb 27 06:23:16 intech9 kernel: ASC=20 ASCQ= 0
Feb 27 06:23:16 intech9 kernel: Raw sense data:0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
and occaisional 'gunzip: unexpected end of file' errors on verifying
the tape.
Take care,
--
Camm Maguire camm@enhanced.com
==========================================================================
"The earth is but one country, and mankind its citizens." -- Baha'u'llah
next reply other threads:[~2001-02-27 16:08 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-02-27 16:06 Camm Maguire [this message]
2001-02-27 15:07 ` 2.2.18 IDE tape problem, with ide-scsi Khalid Aziz
2001-02-27 17:19 ` Camm Maguire
2001-02-27 15:34 ` Khalid Aziz
2001-02-27 19:52 ` Camm Maguire
2001-02-27 18:18 ` Khalid Aziz
2001-02-27 20:26 ` Andre Hedrick
2001-02-27 21:26 ` Khalid Aziz
2001-02-28 15:23 ` Camm Maguire
2001-02-28 15:34 ` Mike Dresser
2001-03-07 22:54 ` Camm Maguire
2001-03-12 16:52 ` Khalid Aziz
2001-03-13 14:14 ` Camm Maguire
2001-02-27 17:32 ` Mike Dresser
2001-02-27 18:31 ` Camm Maguire
2001-02-27 18:34 ` Mike Dresser
2001-02-27 19:05 ` Andre Hedrick
2001-02-27 19:40 ` Camm Maguire
2001-03-01 17:02 ` Khalid Aziz
2001-02-27 22:21 ` Alan Cox
2001-02-27 19:01 ` Andre Hedrick
2001-02-27 19:04 ` Mike Dresser
2001-03-07 0:34 ` [PATCH] " Chip Salzenberg
2001-03-07 1:09 ` Andre Hedrick
[not found] <Pine.LNX.4.10.10102271153560.29323-100000@coffee.psychology.mcmaster.ca>
2001-02-27 17:16 ` Camm Maguire
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=54u25g3yb9.fsf_-_@intech19.enhanced.com \
--to=camm@enhanced.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.