Re: [PATCH v3 2/3] Phy: DT binding documentation for Broadcom Cygnus USB PHY driver

[Kishon Vijay Abraham I <kishon@ti.com>]

Hi,

On Thursday 23 April 2015 04:44 AM, Arun Ramamurthy wrote:
> Broadcom's Cygnus chip has a USB 2.0 host controller connected to
> three separate phys. One of the phs (port 2) is also connectd to
> a usb 2.0 device controller
>
> Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
> Reviewed-by: Ray Jui <rjui@broadcom.com>
> Reviewed-by: Scott Branden <sbranden@broadcom.com>
> ---
>   .../bindings/phy/brcm,cygnus-usb-phy.txt           | 69 ++++++++++++++++++++++
>   include/dt-bindings/phy/phy.h                      |  2 +
>   2 files changed, 71 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt
>
> diff --git a/Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt b/Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt
> new file mode 100644
> index 0000000..ec62044
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt
> @@ -0,0 +1,69 @@
> +BROADCOM CYGNUS USB PHY
> +
> +Required Properties:
> +	- compatible:  brcm,cygnus-usb-phy
> +	- reg : usbphy_regs - Base address of phy registers
> +			usb2h_idm_regs - Base address of host idm registers
> +			usb2d_idm_regs - Base address of device idm registers
> +	- phy-cells - must be 1 for each port declared. The node
> +		      that uses the phy must provide either PHY_CONFIG_DEVICE for device
> +		      or PHY_CONFIG_HOST for host
> +
> +NOTE: port 0 and port 1 are host only and port 2 can be configured for host or
> +device.
> +
> +Example of phy :
> +	usbphy0: usbphy@0x0301c000 {
> +		compatible = "brcm,cygnus-usb-phy";
> +		reg = <0x0301c000 0x2000>,
> +		      <0x18115000 0x1000>,
> +		      <0x18111000 0x1000>;
> +		status = "okay";
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		usbphy0_0: usbphy0@0 {
> +			#phy-cells = <1>;
> +			reg = <0>;
> +			status = "okay";
> +			phy-supply = <&vbus_p0>;
> +		};
> +
> +		usbphy0_1: usbphy0@1 {
> +			#phy-cells = <1>;
> +			reg = <1>;
> +			status = "okay";
> +		};
> +
> +		usbphy0_2: usbphy0@2 {
> +			#phy-cells = <1>;
> +			reg = <2>;
> +			status = "okay";
> +			phy-supply = <&vbus_p2>;
> +		};
> +	};
> +
> +Example of node using the phy:
> +
> +	/* This nodes declares all three ports as host */
> +
> +	ehci0: usb@0x18048000 {
> +		compatible = "generic-ehci";
> +		reg = <0x18048000 0x100>;
> +		interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
> +		phys = <&usbphy0_0 PHY_CONFIG_HOST &usbphy0_1 PHY_CONFIG_HOST &usbphy0_2 PHY_CONFIG_HOST>;
> +		status = "okay";
> +	};
> +
> +	/*
> +	 * This node declares port 2 phy
> +	 * and configures it for device
> +	 */
> +
> +	usbd_udc_dwc1: usbd_udc_dwc@0x1804c000 {
> +		compatible = "iproc-udc";
> +		reg = <0x1804c000 0x2000>;
> +		interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
> +		phys = <&usbphy0_2 PHY_CONFIG_DEVICE>;
> +		phy-names = "usb";
> +	};
> diff --git a/include/dt-bindings/phy/phy.h b/include/dt-bindings/phy/phy.h
> index 6c90193..3f6b1ac 100644
> --- a/include/dt-bindings/phy/phy.h
> +++ b/include/dt-bindings/phy/phy.h
> @@ -15,5 +15,7 @@
>   #define PHY_TYPE_PCIE		2
>   #define PHY_TYPE_USB2		3
>   #define PHY_TYPE_USB3		4
> +#define PHY_CONFIG_HOST		1
> +#define PHY_CONFIG_DEVICE	0

'0' and '1' are already defined for "PHY_NONE" and "PHY_TYPE_SATA". Is this for 
USB2 or for USB3?

Thanks
Kishon