[GIT PULL]Hisilicon hip04 soc and D01 board DT updates for v4.2

[xuwei5@hisilicon.com (Wei Xu)]

On 5/13/2015 8:20 PM, Tyler Baker wrote:
> Hi Wei/Arnd,
> 
> On 12 May 2015 at 08:09, Wei Xu <xuwei5@hisilicon.com> wrote:
>>
>>
>> On 5/12/2015 4:06 PM, Arnd Bergmann wrote:
>>> On Friday 08 May 2015 15:26:09 Wei Xu wrote:
>>>> ARM: DT: Hisilicon hip04 soc and D01 board updates for 4.2
>>>>
>>>> - Add hip04 GPIO nodes
>>>> - Add NANDC nodes for hip04 and D01 board
>>>> - Add hip04 ethernet related nodes
>>>>
>>>>
>>
>> Hi Arnd,
>>
>>> Pulled into next/dt, thanks!
> 
> When this was pulled into arm-soc, the kernelci.org bot reported
> hip04-d01 boot failures[1]. Before bisecting, I decided to wait a day
> and double check the status of -next in case there were needed
> dependencies from other trees. However, now there are the same
> hip04-d01 boot failures in next-20150513[2]. My robot has bisected[3]
> these boot failures down to...
> 
> 828fcfe3c84ade68ecc3f1ba78baebc1654977f3 is the first bad commit
> commit 828fcfe3c84ade68ecc3f1ba78baebc1654977f3
> Author: Zhou Wang <wangzhou.bry@gmail.com>
> Date:   Wed Mar 25 14:57:45 2015 +0800
> 
>     ARM: dts: hip04: add GPIO pieces
> 
>     Hisilicon Soc hip04 has four GPIO controllers, each one has 32
>     GPIOs and can be configured to be an interrupt controller.The GPIO
>     controllers are compatible with the snps,dw-apb-gpio driver.
>     This patch add the corresponding device tree nodes.
> 
>     Acked-by: Linus Walleij <linus.walleij@linaro.org>
>     Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
>     Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

Hi Tyler,

> This commit does not revert cleanly from -next, so I reverted all
> three commits in this pull request on top of next-20150513 and this
> get the hip04-d01 booting again.

It is a little strange.
I checked to this commit "28837bc3e732610ebc7c88ce205dbe43245b1cb8"
at "git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc.git".
and compiled with "hisi_defconfig".

It is booting OK and the log is as below.
And I have also uploaded the binary at "https://github.com/hisilicon/boards/tree/master/D01/for-tyler".
Could you please confirm it again?
Thanks!

Best Regards,
Wei

/ # SC00$
DDR INIT OK!!!
GPIO INIT OK!!!
Boot firmware EVB_SECURE_UEFI_BIOS built at 21:21:53 on May  6 2015
add-symbol-file /home/joyx/develop/github-uefi/Build/D01/DEBUG_GCC49/ARM/HisiPkg/D01BoardPkg/Sec/Sec/Sec/DEBUG/ArmPlatformSec.dll 0xF0100180
Trust Zone Configuration is disabled
UEFI firmware (version EVB_SECURE_UEFI_BIOS built at 18:53:44 on May  6 2015)
add-symbol-file /home/joyx/develop/github-uefi/Build/D01/DEBUG_GCC49/ARM/ArmPlatformPkg/PrePi/PeiMPCore/DEBUG/ArmPlatformPrePiMPCore.dll 0xF0120180
add-symbol-file /home/joyx/develop/github-uefi/Build/D01/DEBUG_GCC49/ARM/MdeModulePkg/Core/Dxe/DxeMain/DEBUG/DxeCore.dll 0x6FAD8240
add-symbol-file /home/joyx/develop/github-uefi/Build/D01/DEBUG_GCC49/ARM/MdeModulePkg/Core/Dxe/DxeMain/DEBUG/DxeCore.dll 0x6FAD8000
add-symbol-file /home/joyx/develop/github-uefi/Build/D01/DEBUG_GCC49/ARM/ArmPkg/Drivers/CpuDxe/CpuDxe/DEBUG/ArmCpuDxe.dll 0x6FA83240
add-symbol-file /home/joyx/develop/github-uefi/Build/D01/DEBUG_GCC49/ARM/MdeModulePkg/Core/RuntimeDxe/RuntimeDxe/DEBUG/RuntimeDxe.dll 0x6FA9F240
add-symbol-file /home/joyx/develop/github-uefi/Build/D01/DEBUG_GCC49/ARM/MdeModulePkg/Universal/SecurityStubDxe/SecurityStubDxe/DEBUG/SecurityStubDxe.dll 0x6FA7E240
add-symbol-file /home/joyx/develop/github-uefi/Build/D01/DEBUG_GCC49/ARM/MdeModulePkg/Universal/Variable/EmuRuntimeDxe/EmuVariableRuntimeDxe/DEBUG/EmuVariableRuntimeDxe.dll 0x6FA97240
add-symbol-file /home/joyx/develop/github-uefi/Build/D01/DEBUG_GCC49/ARM/EmbeddedPkg/EmbeddedMonotonicCounter/EmbeddedMonotonicCounter/DEBUG/EmbeddedMonotonicCounter.dll 0x6FA93240
add-symbol-file /home/joyx/develop/github-uefi/Build/D01/DEBUG_GCC49/ARM/EmbeddedPkg/ResetRuntimeDxe/ResetRuntimeDxe/DEBUG/Reset.dll 0x6AAC9240
add-symbol-file /home/joyx/develop/github-uefi/Build/D01/DEBUG_GCC49/ARM/EmbeddedPkg/RealTimeClockRuntimeDxe/RealTimeClockRuntimeDxe/DEBUG/RealTimeClock.dll 0x6AAC3240
add-symbol-file /home/joyx/develop/github-uefi/Build/D01/DEBUG_GCC49/ARM/EmbeddedPkg/MetronomeDxe/MetronomeDxe/DEBUG/MetronomeDxe.dll 0x6FA79240
add-symbol-file /home/joyx/develop/github-uefi/Build/D01/DEBUG_GCC49/ARM/MdeModulePkg/Universal/HiiDatabaseDxe/HiiDatabaseDxe/DEBUG/HiiDatabase.dll 0x6FA61240
NandFlashInit start
[NANDFlash]  Vendor[0]: MICRON,       MakerCode[0]:    0x0002C
[NANDFlash]  ChipSize[0]: 0x20000000, BlockSize[0]:    0x20000
[NANDFlash]  PageSize[0]: 0x00000800, PagePerBlock[0]: 0x00040
NAND Flash Init OK! Status = Success

Auto boot or not ?(Press 's' to Boot Menu)
Now wait for 2 seconds...

Not Press 's', Start Auto Boot!

Transmit  OS from FLASH to DDR now, please wait![CopyNandToMem : 509]
[CopyNandToMem : 533]PageNumCopy = 1400!

The .kernel file is transmitted ok!

Copy Bootwrapper from FLASH to SRAM...[CopyNandToMem : 509]
[CopyNandToMem : 533]PageNumCopy = 40!

The .text file is transmitted ok!
[CopyNandToMem : 509]
[CopyNandToMem : 533]PageNumCopy = 40!
The .monitor file is transmitted ok!
[CopyNandToMem : 509]
[CopyNandToMem : 533]PageNumCopy = 3000!
THE .FILESYSTEM FILE IS TRANSMITTED OK!
MOVE PC TEXT_SRAM_BASE
C01$
&#C02$
&#C03$
&#C10$
&#C11$
&#C12$
&#C13$
&#C20$
&#C21$
&#C22$
&#C23$
&#C30$
&#C31$
&#C32$
&#C33$
&#[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.1.0-rc3-00364-g28837bc (joyx at f00297740a) (gcc version 4.9.1 20140505 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.05 - Linaro GCC 2014.05) ) #10 SMP PREEMPT Thu May 14 5
[    0.000000] CPU: ARMv7 Processor [413fc0f2] revision 2 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine model: Hisilicon D01 Development Board
[    0.000000] Ignoring memory block 0x4c0000000 - 0x800000000
[    0.000000] earlycon: no match for ttyS0,115200
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] PERCPU: Embedded 9 pages/cpu @edf46000 s15040 r0 d21824 u36864
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 784912
[    0.000000] Kernel command line: console=ttyS0,115200 initrd=0x10d00000,0x1800000 rdinit=/linuxrc earlyprintk
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 3089052K/3145728K available (4416K kernel code, 148K rwdata, 920K rodata, 220K init, 241K bss, 56676K reserved, 0K cma-reserved, 2367488K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]       .text : 0xc0008000 - 0xc053e2ac   (5337 kB)
[    0.000000]       .init : 0xc053f000 - 0xc0576000   ( 220 kB)
[    0.000000]       .data : 0xc0576000 - 0xc059b240   ( 149 kB)
[    0.000000]        .bss : 0xc059e000 - 0xc05da504   ( 242 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] Architected cp15 timer(s) running at 50.00MHz (phys).
[    0.000000] clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns
[    0.000003] sched_clock: 56 bits at 50MHz, resolution 20ns, wraps every 4398046511100ns
[    0.000012] Switching to timer-based delay loop, resolution 20ns
[    0.000082] clocksource arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 38225208935 ns
[    0.000100] sched_clock: 32 bits at 50MHz, resolution 20ns, wraps every 42949672950ns
[    0.000892] Console: colour dummy device 80x30
[    0.000969] Calibrating delay loop (skipped), value calculated using timer frequency.. 100.00 BogoMIPS (lpj=500000)
[    0.001007] pid_max: default: 32768 minimum: 301
[    0.001276] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.001302] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.002711] CPU: Testing write buffer coherency: ok
[    0.003235] /cpus/cpu at 0 missing clock-frequency property
[    0.003279] /cpus/cpu at 1 missing clock-frequency property
[    0.003324] /cpus/cpu at 2 missing clock-frequency property
[    0.003370] /cpus/cpu at 3 missing clock-frequency property
[    0.003420] /cpus/cpu at 100 missing clock-frequency property
[    0.003474] /cpus/cpu at 101 missing clock-frequency property
[    0.003533] /cpus/cpu at 102 missing clock-frequency property
[    0.003597] /cpus/cpu at 103 missing clock-frequency property
[    0.003665] /cpus/cpu at 200 missing clock-frequency property
[    0.003737] /cpus/cpu at 201 missing clock-frequency property
[    0.003814] /cpus/cpu at 202 missing clock-frequency property
[    0.003892] /cpus/cpu at 203 missing clock-frequency property
[    0.003976] /cpus/cpu at 300 missing clock-frequency property
[    0.004065] /cpus/cpu at 301 missing clock-frequency property
[    0.004158] /cpus/cpu at 302 missing clock-frequency property
[    0.004255] /cpus/cpu at 303 missing clock-frequency property
[    0.004284] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.004418] Setting up static identity map for 0x10008280 - 0x100082d8
[    0.004716] HiP04 MCPM initialized
[    0.270900] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.338352] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.405920] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.473505] CPU4: thread -1, cpu 0, socket 1, mpidr 80000100
[    0.541041] CPU5: thread -1, cpu 1, socket 1, mpidr 80000101
[    0.608577] CPU6: thread -1, cpu 2, socket 1, mpidr 80000102
[    0.676148] CPU7: thread -1, cpu 3, socket 1, mpidr 80000103
[    0.743715] CPU8: thread -1, cpu 0, socket 2, mpidr 80000200
[    0.811255] CPU9: thread -1, cpu 1, socket 2, mpidr 80000201
[    0.878793] CPU10: thread -1, cpu 2, socket 2, mpidr 80000202
[    0.946347] CPU11: thread -1, cpu 3, socket 2, mpidr 80000203
[    1.013975] CPU12: thread -1, cpu 0, socket 3, mpidr 80000300
[    1.081452] CPU13: thread -1, cpu 1, socket 3, mpidr 80000301
[    1.149029] CPU14: thread -1, cpu 2, socket 3, mpidr 80000302
[    1.216575] CPU15: thread -1, cpu 3, socket 3, mpidr 80000303
[    1.216795] Brought up 16 CPUs
[    1.216899] SMP: Total of 16 processors activated (1600.00 BogoMIPS).
[    1.216919] CPU: All CPU(s) started in HYP mode.
[    1.216937] CPU: Virtualization extensions available.
[    1.218912] devtmpfs: initialized
[    1.251514] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    1.252528] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    1.252759] pinctrl core: initialized pinctrl subsystem
[    1.270099] NET: Registered protocol family 16
[    1.270878] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    1.292650] Serial: AMBA PL011 UART driver
[    1.314826] SCSI subsystem initialized
[    1.316126] usbcore: registered new interface driver usbfs
[    1.316282] usbcore: registered new interface driver hub
[    1.316760] usbcore: registered new device driver usb
[    1.319857] Switched to clocksource arch_sys_counter
[    1.344958] NET: Registered protocol family 2
[    1.346746] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    1.346931] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    1.347242] TCP: Hash tables configured (established 8192 bind 8192)
[    1.347441] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    1.347523] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    1.348142] NET: Registered protocol family 1
[    1.348941] RPC: Registered named UNIX socket transport module.
[    1.348964] RPC: Registered udp transport module.
[    1.348982] RPC: Registered tcp transport module.
[    1.349001] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.349542] Unpacking initramfs...
[    4.036110] Freeing initrd memory: 24576K (c0d00000 - c2500000)
[    4.041270] futex hash table entries: 4096 (order: 6, 262144 bytes)
[    4.068647] NFS: Registering the id_resolver key type
[    4.068740] Key type id_resolver registered
[    4.068764] Key type id_legacy registered
[    4.069265] bounce: pool size: 64 pages
[    4.069794] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    4.069833] io scheduler noop registered
[    4.069864] io scheduler deadline registered
[    4.070380] io scheduler cfq registered (default)
[    4.217934] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    4.222002] console [ttyS0] disabled
[    4.222186] e4007000.uart: ttyS0 at MMIO 0xe4007000 (irq = 413, base_baud = 10500000) is a 16550A
[    6.529131] console [ttyS0] enabled
[    6.542635] [drm] Initialized drm 1.1.0 20060810
[    6.560545] ahci ea000000.sata: controller can't do NCQ, turning off CAP_NCQ
[    6.584199] ahci ea000000.sata: controller can't do FBS, turning off CAP_FBS
[    6.608078] ahci ea000000.sata: SSS flag set, parallel bus scan disabled
[    6.630673] ahci ea000000.sata: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0xf impl platform mode
[    6.659316] ahci ea000000.sata: flags: sntf stag pm led clo only pmp slum part ccc sxs boh
[    6.693851] scsi host0: ahci
[    6.704676] scsi host1: ahci
[    6.715455] scsi host2: ahci
[    6.726248] scsi host3: ahci
[    6.736636] ata1: SATA max UDMA/133 mmio [mem 0xea000000-0xeaffffff] port 0x100 irq 404
[    6.763580] ata2: SATA max UDMA/133 mmio [mem 0xea000000-0xeaffffff] port 0x180 irq 404
[    6.790470] ata3: SATA max UDMA/133 mmio [mem 0xea000000-0xeaffffff] port 0x200 irq 404
[    6.817320] ata4: SATA max UDMA/133 mmio [mem 0xea000000-0xeaffffff] port 0x280 irq 404
[    8.002404] ata1: SATA link down (SStatus 0 SControl 300)
[    9.251149] ata2: SATA link down (SStatus 0 SControl 300)
[   11.174898] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   11.296724] ata3.00: ATA-8: ST500LM021-1KJ152, 0001SDM1, max UDMA/133
[   11.318388] ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[   12.470360] ata3.00: configured for UDMA/133
[   12.525550] scsi 2:0:0:0: Direct-Access     ATA ST500LM021-1KJ15 SDM1 PQ: 0 ANSI: 5
[   12.554663] sd 2:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[   12.579879] sd 2:0:0:0: [sda] 4096-byte physical blocks
[   12.597919] sd 2:0:0:0: [sda] Write Protect is off
[   12.614225] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   12.687389]  sda: sda1 sda2
[   12.699532] sd 2:0:0:0: [sda] Attached SCSI disk
[   13.739898] ata4: SATA link down (SStatus 0 SControl 300)
[   18.127498] libphy: hip04_mdio_bus: probed
[   18.736446] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   18.758364] ehci-platform: EHCI generic platform driver
[   18.776239] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   18.797023] ohci-platform: OHCI generic platform driver
[   18.814956] usbcore: registered new interface driver usb-storage
[   18.835964] mousedev: PS/2 mouse device common for all mice
[   18.855836] failed to find reboot-offset property
[   18.871770] hisi-reboot: probe of e3e00000.sysctrl failed with error -22
[   18.894752] Synopsys Designware Multimedia Card Interface Driver
[   18.916759] usbcore: registered new interface driver usbhid
[   18.935450] usbhid: USB HID core driver
[   18.951098] NET: Registered protocol family 10
[   18.968938] sit: IPv6 over IPv4 tunneling driver
[   18.986387] NET: Registered protocol family 17
[   19.001496] Key type dns_resolver registered
[   19.016036] Registering SWP/SWPB emulation handler
[   19.034460] hctosys: unable to open rtc device (rtc0)
[   19.054127] ttyS0 - failed to request DMA
[   19.068154] Freeing unused kernel memory: 220K (c053f000 - c0576000)
mount: mounting /dev/sda1 on /mnt/sda1 failed: No such file or directory
[RCS]: /etc/init.d/S01udev
Starting mdev...
[   19.984050] random: sshd urandom read with 8 bits of entropy available
/var/empty must be owned by root and not group or world-writable.

Please press Enter to activate this console.
Welcome to HiLinux.
/ # cat /proc/device-tree/soc/
cat: read error: Is a directory
/ # cat /proc/device-tree/soc/
#address-cells                gpio at 4003000/
#size-cells                   interrupt-controller at c01000/
arm-pmu/                      interrupt-parent
compatible                    mdio/
dual_timer at 3000000/           name
ethernet at 2800000/             nand at 4020000/
ethernet at 2880000/             ppe at 28c0000/
ethernet at 28b0000/             ranges
fabric/                       sata at a000000/
gpio at 4000000/                 sysctrl/
gpio at 4001000/                 uart at 4007000/
gpio at 4002000/
/ # cat /proc/device-tree/soc/



>>
>> Thanks!
>>
>> Best Regards,
>> Wei
>>
>>>       Arnd
>>>
>>> .
>>>
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> 
> Tyler
> 
> [1] http://kernelci.org/boot/all/job/arm-soc/kernel/v4.1-rc3-170-g28837bc3e732/
> [2] http://kernelci.org/boot/all/job/next/kernel/next-20150513/
> [3] https://ci.linaro.org/view/people/job/tbaker-boot-bisect-bot/28/console
> 
> .
>