Re: [PATCH v1 1/1] i2c: designware: Fix hold and setup time issue

[sathyanarayanan kuppuswamy <sathyanarayanan.kuppuswamy-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>]

ping.

On 04/06/2015 07:40 PM, Kuppuswamy Sathyanarayanan wrote:
> If the device configuration is updated by firmware and
> the information is not passed to driver via firmware
> interfaces like ACPI or DT parameters, then that information
> will be lost once the device either resets or suspends. This
> patch checks the boot value of hold and setup time during
> device probe and updates the driver hold and setup time params.
> This fix will ensure that the updates to hold and setup time
> values are not lost after device suspend or resets.
>
> Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
> ---
>   drivers/i2c/busses/i2c-designware-core.c    | 37 +++++++++++++++++++++++++++++
>   drivers/i2c/busses/i2c-designware-core.h    |  2 ++
>   drivers/i2c/busses/i2c-designware-platdrv.c |  4 ++++
>   3 files changed, 43 insertions(+)
>
> diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c
> index 6e25c01..2598207 100644
> --- a/drivers/i2c/busses/i2c-designware-core.c
> +++ b/drivers/i2c/busses/i2c-designware-core.c
> @@ -64,6 +64,7 @@
>   #define DW_IC_RXFLR		0x78
>   #define DW_IC_SDA_HOLD		0x7c
>   #define DW_IC_TX_ABRT_SOURCE	0x80
> +#define DW_IC_SDA_SETUP		0x94
>   #define DW_IC_ENABLE_STATUS	0x9c
>   #define DW_IC_COMP_PARAM_1	0xf4
>   #define DW_IC_COMP_VERSION	0xf8
> @@ -89,6 +90,9 @@
>   					 DW_IC_INTR_TX_ABRT | \
>   					 DW_IC_INTR_STOP_DET)
>   
> +#define DW_IC_DEFAULT_SDA_SETUP	0x64
> +#define DW_IC_DEFAULT_SDA_HOLD	0x1
> +
>   #define DW_IC_STATUS_ACTIVITY	0x1
>   
>   #define DW_IC_ERR_TX_ABRT	0x1
> @@ -271,6 +275,35 @@ static void __i2c_dw_enable(struct dw_i2c_dev *dev, bool enable)
>   		 enable ? "en" : "dis");
>   }
>   
> +/*
> + * Update device default param values if its changed by
> + * firmware
> + */
> +void dw_i2c_update_defaults(struct dw_i2c_dev *dev)
> +{
> +	int ret;
> +
> +	/*
> +	 * make sure default is not updated by firmware
> +	 * interfaces like OF or ACPI
> +	 */
> +
> +	/* SDA hold time update */
> +	if (!dev->sda_hold_time) {
> +		ret = dw_readl(dev, DW_IC_SDA_HOLD);
> +		if ((ret > 0) && (ret != DW_IC_DEFAULT_SDA_HOLD))
> +			dev->sda_hold_time = ret;
> +	}
> +
> +	/* SDA setup time update */
> +	if (!dev->sda_setup_time) {
> +		ret = dw_readl(dev, DW_IC_SDA_SETUP);
> +		if ((ret > 0) && (ret != DW_IC_DEFAULT_SDA_SETUP))
> +			dev->sda_setup_time = ret;
> +	}
> +}
> +EXPORT_SYMBOL_GPL(dw_i2c_update_defaults);
> +
>   /**
>    * i2c_dw_init() - initialize the designware i2c master hardware
>    * @dev: device private data
> @@ -368,6 +401,10 @@ int i2c_dw_init(struct dw_i2c_dev *dev)
>   				"Hardware too old to adjust SDA hold time.");
>   	}
>   
> +	/* Configure SDA setup time if required */
> +	if (dev->sda_setup_time)
> +		dw_writel(dev, dev->sda_setup_time, DW_IC_SDA_SETUP);
> +
>   	/* Configure Tx/Rx FIFO threshold levels */
>   	dw_writel(dev, dev->tx_fifo_depth / 2, DW_IC_TX_TL);
>   	dw_writel(dev, 0, DW_IC_RX_TL);
> diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h
> index 9630222..23ae2e8 100644
> --- a/drivers/i2c/busses/i2c-designware-core.h
> +++ b/drivers/i2c/busses/i2c-designware-core.h
> @@ -98,6 +98,7 @@ struct dw_i2c_dev {
>   	unsigned int		rx_fifo_depth;
>   	int			rx_outstanding;
>   	u32			sda_hold_time;
> +	u32			sda_setup_time;
>   	u32			sda_falling_time;
>   	u32			scl_falling_time;
>   	u16			ss_hcnt;
> @@ -131,3 +132,4 @@ extern int i2c_dw_eval_lock_support(struct dw_i2c_dev *dev);
>   #else
>   static inline int i2c_dw_eval_lock_support(struct dw_i2c_dev *dev) { return 0; }
>   #endif
> +extern void dw_i2c_update_defaults(struct dw_i2c_dev *dev);
> diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c
> index c270f5f..d8995d8 100644
> --- a/drivers/i2c/busses/i2c-designware-platdrv.c
> +++ b/drivers/i2c/busses/i2c-designware-platdrv.c
> @@ -233,6 +233,10 @@ static int dw_i2c_probe(struct platform_device *pdev)
>   		dev->rx_fifo_depth = ((param1 >> 8)  & 0xff) + 1;
>   		dev->adapter.nr = pdev->id;
>   	}
> +
> +	/* call after firmware param update */
> +	dw_i2c_update_defaults(dev);
> +
>   	r = i2c_dw_init(dev);
>   	if (r)
>   		return r;

-- 
Sathyanarayanan Kuppuswamy
Android kernel developer