Re: [PATCH 05/10] ARM: dts: dra7: Use "syscon-phy-power" instead of "ctrl-module" in USB PHY node

[Roger Quadros <rogerq@ti.com>]

On 04/08/15 18:30, Kishon Vijay Abraham I wrote:
> Add "syscon-phy-power" property and remove the deprecated "ctrl-module"
> property from USB PHY devicetree nodes.
> 
> Since "omap_control_usb2phy1", "omap_control_usb3phy1" and
> "omap_control_usb2phy2" devicetree nodes are no longer used, remove it.

s/it/them

> 
> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Acked-by: Roger Quadros <rogerq@ti.com>

cheers,
-roger

> ---
>  arch/arm/boot/dts/dra7.dtsi |   24 +++---------------------
>  1 file changed, 3 insertions(+), 21 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
> index dfefd17..191ffae 100644
> --- a/arch/arm/boot/dts/dra7.dtsi
> +++ b/arch/arm/boot/dts/dra7.dtsi
> @@ -1195,24 +1195,6 @@
>  			clocks = <&sys_32k_ck>;
>  		};
>  
> -		omap_control_usb2phy1: control-phy@4a002300 {
> -			compatible = "ti,control-phy-usb2";
> -			reg = <0x4a002300 0x4>;
> -			reg-names = "power";
> -		};
> -
> -		omap_control_usb3phy1: control-phy@4a002370 {
> -			compatible = "ti,control-phy-pipe3";
> -			reg = <0x4a002370 0x4>;
> -			reg-names = "power";
> -		};
> -
> -		omap_control_usb2phy2: control-phy@0x4a002e74 {
> -			compatible = "ti,control-phy-usb2-dra7";
> -			reg = <0x4a002e74 0x4>;
> -			reg-names = "power";
> -		};
> -
>  		/* OCP2SCP1 */
>  		ocp2scp@4a080000 {
>  			compatible = "ti,omap-ocp2scp";
> @@ -1225,7 +1207,7 @@
>  			usb2_phy1: phy@4a084000 {
>  				compatible = "ti,omap-usb2";
>  				reg = <0x4a084000 0x400>;
> -				ctrl-module = <&omap_control_usb2phy1>;
> +				syscon-phy-power = <&scm_conf 0x300>;
>  				clocks = <&usb_phy1_always_on_clk32k>,
>  					 <&usb_otg_ss1_refclk960m>;
>  				clock-names =	"wkupclk",
> @@ -1236,7 +1218,7 @@
>  			usb2_phy2: phy@4a085000 {
>  				compatible = "ti,dra7x-usb2-phy2", "ti,omap-usb2";
>  				reg = <0x4a085000 0x400>;
> -				ctrl-module = <&omap_control_usb2phy2>;
> +				syscon-phy-power = <&scm_conf 0xe74>;
>  				clocks = <&usb_phy2_always_on_clk32k>,
>  					 <&usb_otg_ss2_refclk960m>;
>  				clock-names =	"wkupclk",
> @@ -1250,7 +1232,7 @@
>  				      <0x4a084800 0x64>,
>  				      <0x4a084c00 0x40>;
>  				reg-names = "phy_rx", "phy_tx", "pll_ctrl";
> -				ctrl-module = <&omap_control_usb3phy1>;
> +				syscon-phy-power = <&scm_conf 0x370>;
>  				clocks = <&usb_phy3_always_on_clk32k>,
>  					 <&sys_clkin1>,
>  					 <&usb_otg_ss1_refclk960m>;
>