Re: Problems loading firmware using built-in drivers with kernels that use initramfs.

[Arend van Spriel <arend@broadcom.com>]

On 08/29/2015 09:11 AM, Takashi Iwai wrote:
> On Sat, 29 Aug 2015 06:09:01 +0200,
> Ming Lei wrote:
>>
>> On Sat, Aug 29, 2015 at 9:11 AM, Luis R. Rodriguez <mcgrof@suse.com> wrote:
>>> On Thu, Aug 27, 2015 at 08:55:13AM +0800, Ming Lei wrote:
>>>> On Thu, Aug 27, 2015 at 2:07 AM, Linus Torvalds
>>>> <torvalds@linux-foundation.org> wrote:
>>>>> On Wed, Aug 26, 2015 at 1:06 AM, Liam Girdwood
>>>>> <liam.r.girdwood@linux.intel.com> wrote:
>>>>>>
>>>>>> I think the options are to either :-
>>>>>>
>>>>>> 1) Don not support audio DSP drivers using topology data as built-in
>>>>>> drivers. Audio is not really a critical system required for booting
>>>>>> anyway.
>>>>>
>>>>> Yes, forcing it to be a module and not letting people compile it in by
>>>>> mistake (and then not have it work) is an option.
>>>>>
>>>>> That said, there are situations where people don't want to use
>>>>> modules. I used to eschew them for security reasons, for example - now
>>>>> I instead just do a one-time temporary key. But others may have other
>>>>> reasons to try to avoid modules.
>>>>>
>>>>>> 2) Create a default PCM for every driver that has topology data on the
>>>>>> assumption that every sound card will at least 1 PCM. This PCM can then
>>>>>> be re-configured when the FW is loaded.
>>>>>
>>>>> That would seem to be the better option if it is reasonably implementable.
>>>>>
>>>>> Of course, some kind of timer-based retry (limited *somehow*) of the
>>>>> fw loading could work too, but smells really really hacky.
>>>>
>>>> Yeah, years ago, we discussed to use -EPROBE_DEFER for the situation,
>>>> which should be one kind of fix, but looks there were objections at that time.
>>>
>>> That would still be a hack. I'll note there is also asynchronous probe support
>>> now but to use that would also be a hack for this issue. We don't want to
>>
>> If we think firmware as one kind of resources like regulators, gpio and others,
>> PROBE_DEFER is one good match for firmware loading case, and
>> it has been used by lots of drivers, so why can't it be used for
>> firmware loading?
>>
>> One problem is that we need to convert drivers into returning -EPROBE_DEFER
>> in case of request failure, and that may involve some work, but which
>> should be mechanical.
>
> I find such a delaying mechanism not so bad, too.  It's very
> straightforward, at least, no big pain in the transition in the driver
> side.

Not sure how this is going to work with request_firmware_nowait(). We 
use that in our drivers to get rid of ~60 sec. delay in probe and 
consequently boot time when built-in. So basically we return 0 on probe 
lacking better knowledge. Guess we can always move back to 
request_firmware calls when defer_probe support is available.

Regards,
Arend

>>> encourage folks to go down that road.  They'd be hacks for this issue as you
>>> are simply delaying the driver probe for a later time and there is no guarantee
>>> that any pivot_root() might have already been completed later to ensure your
>>> driver's fw file is present. So it may work or it may not.
>>
>> We can trigger defer probe explicitly once root fs is setup or other condition
>> is met.
>
> Right, how to trigger the reprobe (and relevant optimization) needs to
> be considered on top of the current mechanism.
>
>
> Takashi
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
>