From: yzhu1 <Yanjun.Zhu@windriver.com>
To: Daniel Borkmann <daniel@iogearbox.net>,
David Miller <davem@davemloft.net>
Cc: <netdev@vger.kernel.org>, <therbert@google.com>,
<jhs@mojatatu.com>, <hannes@stressinduktion.org>,
<edumazet@google.com>, <jeffrey.t.kirsher@intel.com>,
<rusty@rustcorp.com.au>, <brouer@redhat.com>
Subject: Re: [PATCH 1/2] net: Remove ndo_xmit_flush netdev operation, use signalling instead.
Date: Tue, 1 Sep 2015 17:21:16 +0800 [thread overview]
Message-ID: <55E56E0C.7060500@windriver.com> (raw)
In-Reply-To: <55E56080.9020502@iogearbox.net>
On 09/01/2015 04:23 PM, Daniel Borkmann wrote:
> On 09/01/2015 09:10 AM, yzhu1 wrote:
>> On 09/01/2015 03:00 PM, David Miller wrote:
>>> From: yzhu1 <Yanjun.Zhu@windriver.com>
>>> Date: Tue, 1 Sep 2015 14:46:38 +0800
>>>
>>>> After I applied this patch, the skb->xmit_more is not always zero.
>>> There have been thousands upon thousands of commits since that
>>> change.
>>>
>>> You should be testing the tree as it currently stands, to see
>>> if xmit_more behaves correctly or not.
>>>
>>> If xmit_more were incorrectly set to 1 in the current tree, it
>>> would stall the TX queue of the networking device and we would
>>> be seeing lots of reports of this.
>>>
>> Thanks for your reply.
>> Yes. After running for several days, the following messages will appear.
>
> Your below trace says 3.14.29ltsi-WR7.0.0.0 ...
>
> As Dave said, please retest with something up to date, like 4.2 kernel,
> or latest -net git tree.
>
> Besides, the *upstream* xmit_more changes first went into 3.18 ...
> nearest git describe is at:
>
> $ git describe 0b725a2ca61bedc33a2a63d0451d528b268cf975
> v3.17-rc1-251-g0b725a2
>
> So, that only tells me, that you are reporting a possible bug based on
> some non-upstream kernel ... ? Thus, it's not even possible to verify
> if the actual backport was correct ?
Sorry. There is something wrong with backporting this patch.
Thanks for your help.
Zhu Yanjun
>
>> igb 0000:09:00.0: Detected Tx Unit Hang
>> Tx Queue <1>
>> TDH <1a>
>> TDT <1a>
>> next_to_use <1d>
>> next_to_clean <1a>
>> buffer_info[next_to_clean]
>> time_stamp <ffffeb7d>
>> next_to_watch <ffff88103ee711c0>
>> jiffies <fffff324>
>> desc.status <0>
>> igb 0000:09:00.0: Detected Tx Unit Hang
>> Tx Queue <1>
>> TDH <1a>
>> TDT <1a>
>> next_to_use <1d>
>> next_to_clean <1a>
>> buffer_info[next_to_clean]
>> time_stamp <ffffeb7d>
>> next_to_watch <ffff88103ee711c0>
>> jiffies <fffffaf4>
>> desc.status <0>
>> igb 0000:09:00.0: Detected Tx Unit Hang
>> Tx Queue <1>
>> TDH <1a>
>> TDT <1a>
>> next_to_use <1d>
>> next_to_clean <1a>
>> buffer_info[next_to_clean]
>> time_stamp <ffffeb7d>
>> next_to_watch <ffff88103ee711c0>
>> jiffies <1000002c4>
>> desc.status <0>
>> igb 0000:09:00.0: Detected Tx Unit Hang
>> Tx Queue <1>
>> TDH <1a>
>> TDT <1a>
>> next_to_use <1d>------------[ cut here ]------------
>> WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:264
>> dev_watchdog+0x259/0x270()
>> NETDEV WATCHDOG: eth0 (igb): transmit queue 1 timed out
>> Modules linked in: x86_pkg_temp_thermal intel_powerclamp coretemp
>> crct10dif_pclmul crct10dif_common aesni_intel aes_x86_64 glue_helper
>> lrw gf128mul ablk_helper cryptd iTCO_wdt sb_edac iTCO_vendor_support
>> ipmi_si edac_core i2c_i801 lpc_ich ipmi_msghandler nfsd fuse
>> CPU: 0 PID: 0 Comm: swapper/0 Not tainted
>> 3.14.29ltsi-WR7.0.0.0_standard #2
>> Hardware name: Intel Corporation S2600CP/S2600CP, BIOS
>> RMLSDP.86I.R4.26.D674.1304190022 04/19/2013
>> 0000000000000009 ffff88081f603da0 ffffffff81ab9bb8 ffff88081f603de8
>> ffff88081f603dd8 ffffffff8104c64d 0000000000000001 ffff880812f6d940
>> 0000000000000000 ffff880813efc000 0000000000000008 ffff88081f603e38
>> Call Trace:
>> <IRQ> [<ffffffff81ab9bb8>] dump_stack+0x4e/0x7a
>> [<ffffffff8104c64d>] warn_slowpath_common+0x7d/0xa0
>> [<ffffffff8104c6bc>] warn_slowpath_fmt+0x4c/0x50
>> [<ffffffff81ac09c7>] ? _raw_spin_unlock+0x17/0x30
>> [<ffffffff81998659>] dev_watchdog+0x259/0x270
>> [<ffffffff81998400>] ? dev_graft_qdisc+0x80/0x80
>> [<ffffffff810594cb>] call_timer_fn+0x3b/0x170
>> [<ffffffff81998400>] ? dev_graft_qdisc+0x80/0x80
>> [<ffffffff81059d64>] run_timer_softirq+0x1c4/0x2d0
>> [<ffffffff81051557>] __do_softirq+0xb7/0x2e0
>> [<ffffffff810518be>] irq_exit+0x7e/0xa0
>> [<ffffffff81acae74>] smp_apic_timer_interrupt+0x44/0x50
>> [<ffffffff81ac9c4a>] apic_timer_interrupt+0x6a/0x70
>> <EOI> [<ffffffff81880706>] ? cpuidle_enter_state+0x46/0xb0
>> [<ffffffff8188082c>] cpuidle_idle_call+0xbc/0x250
>> [<ffffffff8100cdce>] arch_cpu_idle+0xe/0x20
>> [<ffffffff810a2bb5>] cpu_startup_entry+0x185/0x290
>> [<ffffffff81ab4424>] rest_init+0x84/0x90
>> [<ffffffff82333d50>] start_kernel+0x3d6/0x3e3
>> [<ffffffff82333495>] x86_64_start_reservations+0x2a/0x2c
>> [<ffffffff8233358e>] x86_64_start_kernel+0xf7/0xfa
>> ---[ end trace 57ad9eaf9dd80dc2 ]---
>> igb 0000:09:00.0 eth0: Reset adapter
>> igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
>> igb 0000:09:00.0: Detected Tx Unit Hang
>>
>> next_to_clean <1a>
>> buffer_info[next_to_clean]
>> time_stamp <ffffeb7d>
>> next_to_watch <ffff88103ee711c0>
>> jiffies <100000a94>
>> desc.status <0>
>>
>>
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe netdev" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
>
>
next prev parent reply other threads:[~2015-09-01 9:23 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-08-25 23:35 [PATCH 1/2] net: Remove ndo_xmit_flush netdev operation, use signalling instead David Miller
2014-08-26 3:42 ` Tom Herbert
2014-08-26 4:50 ` David Miller
2015-09-01 6:46 ` yzhu1
2015-09-01 7:00 ` David Miller
2015-09-01 7:10 ` yzhu1
2015-09-01 7:13 ` David Miller
2015-09-01 8:23 ` Daniel Borkmann
2015-09-01 9:21 ` yzhu1 [this message]
2015-09-01 16:22 ` Alexander Duyck
2015-09-01 16:49 ` Paul Gortmaker
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=55E56E0C.7060500@windriver.com \
--to=yanjun.zhu@windriver.com \
--cc=brouer@redhat.com \
--cc=daniel@iogearbox.net \
--cc=davem@davemloft.net \
--cc=edumazet@google.com \
--cc=hannes@stressinduktion.org \
--cc=jeffrey.t.kirsher@intel.com \
--cc=jhs@mojatatu.com \
--cc=netdev@vger.kernel.org \
--cc=rusty@rustcorp.com.au \
--cc=therbert@google.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.