From: Jorge Baranda <jbaranda@cttc.es>
To: ath10k@lists.infradead.org
Subject: Re: Setting up a VHT ad-hoc connection with ath10k
Date: Mon, 07 Sep 2015 12:36:41 +0200 [thread overview]
Message-ID: <55ED68B9.2060509@cttc.es> (raw)
In-Reply-To: <CALhHN=puF0RX=iSoxSH-GaEAhzb9eJbR38p7jOaXE7e3-dGDdw@mail.gmail.com>
Dear Janusz,
By firmware 636, do you mean the one named 999.999.0.636 in the url:
https://wireless.wiki.kernel.org/en/users/drivers/ath10k/firmware?
And then, if I use wpa_supplicant could it be possible to setup an ADHOC
connection.
I thought wpa_supplicant is used to setup STAs in combination with
hostapd (to setup APs).
Thank you very much for your time and attention,
Kind regards,
Jorge
El 07/09/15 12:22, Janusz Dziedzic escribió:
> On 7 September 2015 at 11:48, Jorge Baranda <jbaranda@cttc.es> wrote:
>> Dear all,
>>
>> Recently, I bought some WLE900VX cards and equipped several computers with
>> such cards.
>> I want to check the capabilties of these cards, so I have thought of
>> establishing an AD-HOC 802.11ac link in order to do so.
>> I have been able to establish and AD-HOC connection between two of these
>> cards, but I am sure I am not establishing an 802.11ac connection because
>> the iwlist tool only reports bit rates up to 54Mb/s for the established
>> connection.
>> I would be very grateful if someone could provide me some hints on
>> configuring these cards to work using the 802.11ac and to check that the
>> connection using such protocol has been established.
>>
> You should use 636 firmware and lastes wpa_supplicant. Wpa_supplicant
> will setup AC correctly (iw don't support this yet). After connected,
> check if you have correct BW (80MHz) using:
> iw wlan0 info
>
> Next you can run some traffic eg. using iperf and check RX rate using:
> iw wlan0 station dump.
>
> BR
> Janusz
>
>> Thank you very much in advance for your time and attention,
>>
>> With kind regards,
>>
>> --
>> Jorge Baranda
>> Research Engineer, MSc
>> jorge.baranda@cttc.es
>>
>> Centre Tecnològic de Telecomunicacions de Catalunya (CTTC)
>> Av. Carl Friedrich Gauss, 7
>> 08860 Castelldefels, Barcelona (Spain)
>> Tel: +34 93 645 29 00 Ext: 2171
>> Fax. +34 93 645 29 01
>> www.cttc.es
>>
>>
>> _______________________________________________
>> ath10k mailing list
>> ath10k@lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/ath10k
> _______________________________________________
> ath10k mailing list
> ath10k@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/ath10k
--
Jorge Baranda
Research Engineer, MSc
jorge.baranda@cttc.es
Centre Tecnològic de Telecomunicacions de Catalunya (CTTC)
Av. Carl Friedrich Gauss, 7
08860 Castelldefels, Barcelona (Spain)
Tel: +34 93 645 29 00 Ext: 2171
Fax. +34 93 645 29 01
www.cttc.es
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
next prev parent reply other threads:[~2015-09-07 10:37 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-05 15:08 IBSS-RSN support on ath10k only links Alessandro Bolletta
2015-09-05 20:00 ` Janusz Dziedzic
2015-09-07 7:48 ` R: " Alessandro Bolletta
2015-09-07 8:02 ` Janusz Dziedzic
2015-09-07 8:03 ` R: " Alessandro Bolletta
2015-09-07 8:22 ` Janusz Dziedzic
2015-09-07 9:48 ` Setting up a VHT ad-hoc connection with ath10k Jorge Baranda
2015-09-07 10:22 ` Janusz Dziedzic
2015-09-07 10:36 ` Jorge Baranda [this message]
2015-09-07 15:36 ` IBSS-RSN support on ath10k only links Ben Greear
2015-09-07 15:40 ` R: " Alessandro Bolletta
2015-09-07 15:44 ` Ben Greear
2015-09-07 16:04 ` R: " Alessandro Bolletta
2015-09-07 16:59 ` Ben Greear
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=55ED68B9.2060509@cttc.es \
--to=jbaranda@cttc.es \
--cc=ath10k@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.