From: Johan Sagaert <sagaert.johan@proximus.be>
To: buildroot@busybox.net
Subject: [Buildroot] problem booting from ext2 µsd card
Date: Thu, 17 Sep 2015 01:56:20 +0200 [thread overview]
Message-ID: <55FA01A4.5070107@proximus.be> (raw)
Hi
just extracted my rootfs to a ?sd card
configured u-boot to boot from it
Any idea ? i have a single ext2 partition on a 4GB transcend class 10 card.
not sure where to start searching...
Tried several cards with equal results.
used cfdisk as tool.
snip from bootlog
usbcore: registered new interface driver usb-storage
ci_hdrc ci_hdrc.1: EHCI Host Controller
ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
input: 20b8000.kpp as
/devices/soc0/soc/2000000.aips-bus/20b8000.kpp/input/input0
input: EP0700M06 as
/devices/soc0/soc/2100000.aips-bus/21a8000.i2c/i2c-2/2-0038/input/input1
rtc-ds1307 0-0068: rtc core: registered ds1339 as rtc0
snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp
as rtc1
i2c /dev entries driver
mxc_v4l2_output v4l2_out: V4L2 device registered as video16
mxc_v4l2_output v4l2_out: V4L2 device registered as video17
imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: no vqmmc regulator found
mmc0: no vmmc regulator found
mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
mmc1: no vqmmc regulator found
mmc1: no vmmc regulator found
mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
galcore: clk_get vg clock failed, disable vg!
Galcore version 5.0.11.25762
mmc0: new high speed SDHC card at address 59b4
*mmcblk0: mmc0:59b4 USD 3.74 GiB
mmcblk0: p1*
mxc_vpu 2040000.vpu: VPU initialized
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
sgtl5000 2-000a: sgtl5000 revision 0x11
2-000a: 1200 mV normal
sgtl5000 2-000a: Using internal LDO instead of VDDD
imx-sgtl5000 sound: sgtl5000 <-> 2028000.ssi mapping ok
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
failed to disable 1.2 GHz OPP
Registering SWP/SWPB emulation handler
input: gpio-keys as /devices/soc0/gpio-keys/input/input2
rtc-ds1307 0-0068: setting system clock to 2000-01-01 13:27:11 UTC
(946733231)
ALSA device list:
#0: sgtl5000-audio
VFS: Mounted root (ext2 filesystem) on device 179:1.
devtmpfs: mounted
Freeing unused kernel memory: 252K (80835000 - 80874000)
Starting logging: OK
Populating /dev using udev: udevd[116]: starting version 3.1.1
random: udevd urandom read with 55 bits of entropy available
done
Initializing random number generator... done.
Starting system message bus: done
Starting rpcbind: OK
Starting network...
fec 2188000.ethernet eth0: Freescale FEC PHY driver [SMSC
LAN8710/LAN8720] (mii_bus:phy_addr=2188000.ethernet:00, irq=-1)
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.23.2) started
Sending discover...
Sending discover...
fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Sending discover...
Sending select for 192.168.1.145...
Lease of 192.168.1.145 obtained, lease time 3600
deleting routers
adding dns 192.168.1.1
Starting ntpd: OK
Starting dropbear sshd: OK
Starting inetd : OK
/etc/init.d/S80tunetouch: line 16: can't create
/sys/bus/i2c/devices/0-0038/threshold: nonexistent directory
/etc/init.d/S80tunetouch: line 16: can't create
/sys/bus/i2c/devices/0-0038/gain: nonexistent directory
/etc/init.d/S80tunetouch: line 16: can't create
/sys/bus/i2c/devices/0-0038/report_rate: nonexistent directory
Starting mpd: OK
Segmentation fault
fb-test 1.1.0 (rosetta)
fb res 800x480 virtual 800x480, line_len 3200, bpp 32
attempt to access beyond end of device
mmcblk0p1: rw=0, want=11524007040, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=33325320632, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=20728214080, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=8149861624, limit=7857074
attempt to access beyond end of device
Welcome to Buildrootmmcblk0p1: rw=0, want=26925577088, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=11576436144, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=26035639288, limit=7857074
attempt to access beyond end of device
apex_systems login: mmcblk0p1: rw=0, want=30960508736, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=873814192, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=18769465248, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=13401729144, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=8730814792, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=30741356216, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=7043620368, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=13247852320, limit=7857074
attempt to access beyond end of device
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20150917/b8cdd2f8/attachment.html>
next reply other threads:[~2015-09-16 23:56 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-16 23:56 Johan Sagaert [this message]
2015-09-17 0:27 ` [Buildroot] problem booting from ext2 µsd card Brendan Heading
2015-09-17 8:03 ` Johan Sagaert
2015-09-17 11:20 ` Brendan Heading
2015-09-20 23:59 ` Johan Sagaert
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=55FA01A4.5070107@proximus.be \
--to=sagaert.johan@proximus.be \
--cc=buildroot@busybox.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.