From: Thomas Chou <thomas@wytron.com.tw>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v2 2/5] net: altera_tse: use data type u32 for regs and desc
Date: Fri, 6 Nov 2015 09:31:45 +0800 [thread overview]
Message-ID: <563C0301.6030303@wytron.com.tw> (raw)
In-Reply-To: <1446728090-5969-2-git-send-email-thomas@wytron.com.tw>
On 2015?11?05? 20:54, Thomas Chou wrote:
> Use data type u32/u16/u8 for regs and desc, as it is more
> portable.
>
> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
> Reviewed-by: Marek Vasut <marex@denx.de>
> Reviewed-by: Chin Liang See <clsee@altera.com>
> ---
> drivers/net/altera_tse.c | 16 ++++----
> drivers/net/altera_tse.h | 104 +++++++++++++++++++++++------------------------
> 2 files changed, 60 insertions(+), 60 deletions(-)
>
Applied to u-boot-nios.
> diff --git a/drivers/net/altera_tse.c b/drivers/net/altera_tse.c
> index 319983c..394503f 100644
> --- a/drivers/net/altera_tse.c
> +++ b/drivers/net/altera_tse.c
> @@ -27,12 +27,12 @@ static inline void alt_sgdma_construct_descriptor(
> struct alt_sgdma_descriptor *next,
> void *read_addr,
> void *write_addr,
> - unsigned short length_or_eop,
> + u16 length_or_eop,
> int generate_eop,
> int read_fixed,
> int write_fixed_or_sop)
> {
> - unsigned char val;
> + u8 val;
>
> /*
> * Mark the "next" descriptor as "not" owned by hardware. This prevents
> @@ -100,7 +100,7 @@ static int alt_sgdma_wait_transfer(struct alt_sgdma_registers *regs)
> static int alt_sgdma_start_transfer(struct alt_sgdma_registers *regs,
> struct alt_sgdma_descriptor *desc)
> {
> - unsigned int val;
> + u32 val;
>
> /* Point the controller at the descriptor */
> writel(virt_to_phys(desc), ®s->next_descriptor_pointer);
> @@ -121,7 +121,7 @@ static void tse_adjust_link(struct altera_tse_priv *priv,
> struct phy_device *phydev)
> {
> struct alt_tse_mac *mac_dev = priv->mac_dev;
> - unsigned int refvar;
> + u32 refvar;
>
> if (!phydev->link) {
> debug("%s: No link.\n", phydev->dev->name);
> @@ -230,7 +230,7 @@ static void altera_tse_stop(struct udevice *dev)
> struct alt_sgdma_registers *rx_sgdma = priv->sgdma_rx;
> struct alt_sgdma_registers *tx_sgdma = priv->sgdma_tx;
> struct alt_sgdma_descriptor *rx_desc = priv->rx_desc;
> - unsigned int status;
> + u32 status;
> int ret;
> ulong ctime;
>
> @@ -266,7 +266,7 @@ static int tse_mdio_read(struct mii_dev *bus, int addr, int devad, int reg)
> {
> struct altera_tse_priv *priv = bus->priv;
> struct alt_tse_mac *mac_dev = priv->mac_dev;
> - unsigned int value;
> + u32 value;
>
> /* set mdio address */
> writel(addr, &mac_dev->mdio_phy1_addr);
> @@ -337,7 +337,7 @@ static int altera_tse_write_hwaddr(struct udevice *dev)
> struct alt_tse_mac *mac_dev = priv->mac_dev;
> struct eth_pdata *pdata = dev_get_platdata(dev);
> u8 *hwaddr = pdata->enetaddr;
> - unsigned int mac_lo, mac_hi;
> + u32 mac_lo, mac_hi;
>
> mac_lo = (hwaddr[3] << 24) | (hwaddr[2] << 16) |
> (hwaddr[1] << 8) | hwaddr[0];
> @@ -362,7 +362,7 @@ static int altera_tse_start(struct udevice *dev)
> {
> struct altera_tse_priv *priv = dev_get_priv(dev);
> struct alt_tse_mac *mac_dev = priv->mac_dev;
> - unsigned int val;
> + u32 val;
> int ret;
>
> /* need to create sgdma */
> diff --git a/drivers/net/altera_tse.h b/drivers/net/altera_tse.h
> index f289bff..a96351a 100644
> --- a/drivers/net/altera_tse.h
> +++ b/drivers/net/altera_tse.h
> @@ -54,34 +54,34 @@
> *
> */
> struct alt_sgdma_descriptor {
> - unsigned int source; /* the address of data to be read. */
> - unsigned int source_pad;
> + u32 source; /* the address of data to be read. */
> + u32 source_pad;
>
> - unsigned int destination; /* the address to write data */
> - unsigned int destination_pad;
> + u32 destination; /* the address to write data */
> + u32 destination_pad;
>
> - unsigned int next; /* the next descriptor in the list. */
> - unsigned int next_pad;
> + u32 next; /* the next descriptor in the list. */
> + u32 next_pad;
>
> - unsigned short bytes_to_transfer; /* the number of bytes to transfer */
> - unsigned char read_burst;
> - unsigned char write_burst;
> + u16 bytes_to_transfer; /* the number of bytes to transfer */
> + u8 read_burst;
> + u8 write_burst;
>
> - unsigned short actual_bytes_transferred;/* bytes transferred by DMA */
> - unsigned char descriptor_status;
> - unsigned char descriptor_control;
> + u16 actual_bytes_transferred;/* bytes transferred by DMA */
> + u8 descriptor_status;
> + u8 descriptor_control;
>
> } __packed_1_;
>
> /* SG-DMA Control/Status Slave registers map */
>
> struct alt_sgdma_registers {
> - unsigned int status;
> - unsigned int status_pad[3];
> - unsigned int control;
> - unsigned int control_pad[3];
> - unsigned int next_descriptor_pointer;
> - unsigned int descriptor_pad[3];
> + u32 status;
> + u32 status_pad[3];
> + u32 control;
> + u32 control_pad[3];
> + u32 next_descriptor_pointer;
> + u32 descriptor_pad[3];
> };
>
> /* TSE Stuff */
> @@ -98,47 +98,47 @@ struct alt_sgdma_registers {
> /* MAC register Space */
>
> struct alt_tse_mac {
> - unsigned int megacore_revision;
> - unsigned int scratch_pad;
> - unsigned int command_config;
> - unsigned int mac_addr_0;
> - unsigned int mac_addr_1;
> - unsigned int max_frame_length;
> - unsigned int pause_quanta;
> - unsigned int rx_sel_empty_threshold;
> - unsigned int rx_sel_full_threshold;
> - unsigned int tx_sel_empty_threshold;
> - unsigned int tx_sel_full_threshold;
> - unsigned int rx_almost_empty_threshold;
> - unsigned int rx_almost_full_threshold;
> - unsigned int tx_almost_empty_threshold;
> - unsigned int tx_almost_full_threshold;
> - unsigned int mdio_phy0_addr;
> - unsigned int mdio_phy1_addr;
> -
> - unsigned int reserved1[0x29];
> + u32 megacore_revision;
> + u32 scratch_pad;
> + u32 command_config;
> + u32 mac_addr_0;
> + u32 mac_addr_1;
> + u32 max_frame_length;
> + u32 pause_quanta;
> + u32 rx_sel_empty_threshold;
> + u32 rx_sel_full_threshold;
> + u32 tx_sel_empty_threshold;
> + u32 tx_sel_full_threshold;
> + u32 rx_almost_empty_threshold;
> + u32 rx_almost_full_threshold;
> + u32 tx_almost_empty_threshold;
> + u32 tx_almost_full_threshold;
> + u32 mdio_phy0_addr;
> + u32 mdio_phy1_addr;
> +
> + u32 reserved1[0x29];
>
> /*FIFO control register. */
> - unsigned int tx_cmd_stat;
> - unsigned int rx_cmd_stat;
> + u32 tx_cmd_stat;
> + u32 rx_cmd_stat;
>
> - unsigned int reserved2[0x44];
> + u32 reserved2[0x44];
>
> /*Registers 0 to 31 within PHY device 0/1 */
> - unsigned int mdio_phy0[0x20];
> - unsigned int mdio_phy1[0x20];
> + u32 mdio_phy0[0x20];
> + u32 mdio_phy1[0x20];
>
> /*4 Supplemental MAC Addresses */
> - unsigned int supp_mac_addr_0_0;
> - unsigned int supp_mac_addr_0_1;
> - unsigned int supp_mac_addr_1_0;
> - unsigned int supp_mac_addr_1_1;
> - unsigned int supp_mac_addr_2_0;
> - unsigned int supp_mac_addr_2_1;
> - unsigned int supp_mac_addr_3_0;
> - unsigned int supp_mac_addr_3_1;
> -
> - unsigned int reserved3[0x38];
> + u32 supp_mac_addr_0_0;
> + u32 supp_mac_addr_0_1;
> + u32 supp_mac_addr_1_0;
> + u32 supp_mac_addr_1_1;
> + u32 supp_mac_addr_2_0;
> + u32 supp_mac_addr_2_1;
> + u32 supp_mac_addr_3_0;
> + u32 supp_mac_addr_3_1;
> +
> + u32 reserved3[0x38];
> };
>
> struct altera_tse_priv {
>
next prev parent reply other threads:[~2015-11-06 1:31 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-11-04 9:12 [U-Boot] [PATCH 1/6] net: altera_tse: use data type u32 for regs and desc Thomas Chou
2015-11-04 9:12 ` [U-Boot] [PATCH 2/6] net: altera_tse: fix packed and aligned attribute Thomas Chou
2015-11-04 16:06 ` Chin Liang See
2015-11-04 9:12 ` [U-Boot] [PATCH 3/6] net: altera_tse: fix CamelCase Thomas Chou
2015-11-04 16:17 ` Chin Liang See
2015-11-05 13:30 ` Thomas Chou
2015-11-04 9:12 ` [U-Boot] [PATCH 4/6] net: altera_tse: remove the useless parenthesis Thomas Chou
2015-11-04 16:18 ` Chin Liang See
2015-11-04 9:12 ` [U-Boot] [PATCH 5/6] net: altera_tse: remove unused macro Thomas Chou
2015-11-04 16:20 ` Chin Liang See
2015-11-04 9:12 ` [U-Boot] [PATCH 6/6] net: altera_tse: use BIT macro Thomas Chou
2015-11-04 13:51 ` Marek Vasut
2015-11-04 16:22 ` Chin Liang See
2015-11-04 16:46 ` Jagan Teki
2015-11-04 16:05 ` [U-Boot] [PATCH 1/6] net: altera_tse: use data type u32 for regs and desc Chin Liang See
2015-11-05 12:54 ` [U-Boot] [PATCH v2 1/5] net: altera_tse: remove unused macro and regs def Thomas Chou
2015-11-05 12:54 ` [U-Boot] [PATCH v2 2/5] net: altera_tse: use data type u32 for regs and desc Thomas Chou
2015-11-05 22:09 ` Joe Hershberger
2015-11-06 1:31 ` Thomas Chou [this message]
2015-11-05 12:54 ` [U-Boot] [PATCH v2 3/5] net: altera_tse: fix packed and aligned attribute Thomas Chou
2015-11-05 22:09 ` Joe Hershberger
2015-11-06 1:32 ` Thomas Chou
2015-11-05 12:54 ` [U-Boot] [PATCH v2 4/5] net: altera_tse: remove the useless parenthesis Thomas Chou
2015-11-05 22:09 ` Joe Hershberger
2015-11-06 1:32 ` Thomas Chou
2015-11-05 12:54 ` [U-Boot] [PATCH v2 5/5] net: altera_tse: use BIT macro Thomas Chou
2015-11-05 22:09 ` Joe Hershberger
2015-11-06 1:32 ` Thomas Chou
2015-11-05 22:08 ` [U-Boot] [PATCH v2 1/5] net: altera_tse: remove unused macro and regs def Joe Hershberger
2015-11-06 1:31 ` Thomas Chou
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=563C0301.6030303@wytron.com.tw \
--to=thomas@wytron.com.tw \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.