From: Julien Meunier <julien.meunier@6wind.com>
To: "Zhang, Helin" <helin.zhang@intel.com>, dev@dpdk.org
Subject: i40e: cannot change mtu to enable jumbo frame
Date: Tue, 09 Feb 2016 17:35:45 +0100 [thread overview]
Message-ID: <56BA1561.3060201@6wind.com> (raw)
Hello Helin,
I tried to send jumbo frames to a i40e card. However, I observed that
all frames are dropped. Moreover, set_mtu function is not implemented on
i40e PMD.
> testpmd --log-level 8 --huge-dir=/mnt/huge -n 4 -l 2,18 --socket-mem
1024,1024 -w 0000:02:00.0 -w 0000:02:00.2 -- -i --nb-cores=1
--nb-ports=2 --total-num-mbufs=65536
=============
Configuration
=============
+-----------+ +-------------+
| | | |
| tgen | | |
| +----------+ port 0 |
| | | |
| | | |
| | | |
| | | |
| +----------+ port 1 |
| | | |
+-----------+ +-------------+
DPDK: DPDK-v2.2
==========
MTU = 1500
==========
Packet sent from a tgen
> p = Ether / IP / UDP / Raw(MTU + HDR(Ethernet)- HDR(IP) - HDR(UDP))
> len(p) = 1514
testpmd> start
PMD: i40e_rxd_to_vlan_tci(): Mbuf vlan_tci: 0, vlan_tci_outer: 0
testpmd> stop
Telling cores to stop...
Waiting for lcores to finish...
PMD: i40e_update_vsi_stats(): *** VSI[13] stats start ***
PMD: i40e_update_vsi_stats(): rx_bytes: 1518
PMD: i40e_update_vsi_stats(): rx_unicast: 1
PMD: i40e_update_vsi_stats(): *** VSI[13] stats end ***
PMD: i40e_dev_stats_get(): *** PF stats start ***
PMD: i40e_dev_stats_get(): rx_bytes: 1514
PMD: i40e_dev_stats_get(): rx_unicast: 1
PMD: i40e_dev_stats_get(): rx_unknown_protocol: 1
PMD: i40e_dev_stats_get(): rx_size_1522: 1
PMD: i40e_dev_stats_get(): *** PF stats end ***
-------------- Forward statistics for port 0 --------------
RX-packets: 1 RX-dropped: 0 RX-total: 1
TX-packets: 0 TX-dropped: 0 TX-total: 0
----------------------------------------------------------------------------
PMD: i40e_update_vsi_stats(): *** VSI[14] stats start ***
PMD: i40e_update_vsi_stats(): tx_bytes: 1514
PMD: i40e_update_vsi_stats(): tx_unicast: 1
PMD: i40e_update_vsi_stats(): *** VSI[14] stats end ***
PMD: i40e_dev_stats_get(): *** PF stats start ***
PMD: i40e_dev_stats_get(): tx_bytes: 1514
PMD: i40e_dev_stats_get(): tx_unicast: 1
PMD: i40e_dev_stats_get(): tx_size_1522: 1
PMD: i40e_dev_stats_get(): *** PF stats end ***
-------------- Forward statistics for port 1 --------------
RX-packets: 0 RX-dropped: 0 RX-total: 0
TX-packets: 1 TX-dropped: 0 TX-total: 1
----------------------------------------------------------------------------
+++++ Accumulated forward statistics for all ports+++++
RX-packets: 1 RX-dropped: 0 RX-total: 1
TX-packets: 1 TX-dropped: 0 TX-total: 1
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
=> OK
==========
MTU = 1600
==========
Packet sent
> p = Ether / IP / UDP / Raw(MTU + HDR(Ethernet)- HDR(IP) - HDR(UDP))
> len(p) = 1614
testpmd> port config mtu 0 1600
rte_eth_dev_set_mtu: Function not supported
Set MTU failed. diag=-95
testpmd> port config mtu 1 1600
rte_eth_dev_set_mtu: Function not supported
Set MTU failed. diag=-95
testpmd> start
testpmd> stop
Telling cores to stop...
Waiting for lcores to finish...
PMD: i40e_update_vsi_stats(): *** VSI[13] stats start ***
PMD: i40e_update_vsi_stats(): rx_bytes: 1618
PMD: i40e_update_vsi_stats(): rx_unicast: 1
PMD: i40e_update_vsi_stats(): *** VSI[13] stats end ***
PMD: i40e_dev_stats_get(): *** PF stats start ***
PMD: i40e_dev_stats_get(): rx_bytes: 1614
PMD: i40e_dev_stats_get(): rx_unicast: 1
PMD: i40e_dev_stats_get(): rx_unknown_protocol: 1
PMD: i40e_dev_stats_get(): rx_size_big: 1
PMD: i40e_dev_stats_get(): *** PF stats end ***
-------------- Forward statistics for port 0 --------------
RX-packets: 1 RX-dropped: 0 RX-total: 1
TX-packets: 0 TX-dropped: 0 TX-total: 0
----------------------------------------------------------------------------
PMD: i40e_update_vsi_stats(): *** VSI[14] stats start ***
PMD: i40e_update_vsi_stats(): tx_bytes: 0
PMD: i40e_update_vsi_stats(): tx_unicast: 0
PMD: i40e_update_vsi_stats(): *** VSI[14] stats end ***
PMD: i40e_dev_stats_get(): *** PF stats start ***
PMD: i40e_dev_stats_get(): tx_bytes: 0
PMD: i40e_dev_stats_get(): tx_unicast: 0
PMD: i40e_dev_stats_get(): tx_size_big: 0
PMD: i40e_dev_stats_get(): *** PF stats end ***
-------------- Forward statistics for port 1 --------------
RX-packets: 0 RX-dropped: 0 RX-total: 0
TX-packets: 0 TX-dropped: 0 TX-total: 0
----------------------------------------------------------------------------
+++++ Accumulated forward statistics for all ports+++++
RX-packets: 1 RX-dropped: 0 RX-total: 1
TX-packets: 0 TX-dropped: 0 TX-total: 0
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Done.
=> Frame correctly received on port 0, but never forwarded or xmit on
port 1.
Does a mtu_set function will be developed soon in order to support jumbo
frame ?
Regards,
--
Julien MEUNIER
6WIND
next reply other threads:[~2016-02-09 16:36 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-02-09 16:35 Julien Meunier [this message]
2016-02-09 19:05 ` i40e: cannot change mtu to enable jumbo frame Zhu, Heqing
2016-02-10 10:53 ` Julien Meunier
2016-02-10 13:54 ` Ananyev, Konstantin
2016-02-10 15:20 ` Zhang, Helin
2016-02-12 14:08 ` Julien Meunier
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=56BA1561.3060201@6wind.com \
--to=julien.meunier@6wind.com \
--cc=dev@dpdk.org \
--cc=helin.zhang@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.