From: Itaru Kitayama <itaru.kitayama@riken.jp>
To: linux-kernel@vger.kernel.org
Subject: RE: [PATCH v6 0/3] mailbox: Add APM X-Gene platform mailbox driver
Date: Sat, 13 Feb 2016 13:56:35 +0900 [thread overview]
Message-ID: <56BEB783.1050105@riken.jp> (raw)
Hi Duc,
I've been testing your patch set for v4.5-rc1 on Mustang, with ACPI,
however the boot hangs in the middle of it:
EFI stub: Booting Linux Kernel...
EFI stub: Using DTB from configuration table
EFI stub: Exiting boot services and installing virtual address map...
L3c Cache: 8MB
Booting Linux on physical CPU 0x0
Linux version 4.5.0-rc1+ (itaru.kitayama@r2-a21) (gcc version 5.3.1
20151207 (Red Hat 5.3.1-2) (GCC) ) #96 SMP PREEMPT Fri Feb 12 22:43:54
CST 2016
Boot CPU: AArch64 Processor [500f0001]
earlycon: Early serial console at MMIO32 0x1c020000 (options '')
bootconsole [uart0] enabled
efi: Getting EFI parameters from FDT:
EFI v2.40 by X-Gene Mustang Board EFI Nov 24 2015 13:22:41
efi: ACPI=0x47fa869000 ACPI 2.0=0x47fa869014 SMBIOS 3.0=0x47fa867000
cma: Reserved 512 MiB at 0x00000040e0000000
ACPI: Early table checksum verification disabled
ACPI: RSDP 0x00000047FA869014 000024 (v02 APM )
ACPI: XSDT 0x00000047FA8680E8 00006C (v01 APM XGENE 00000003
01000013)
ACPI: FACP 0x00000047FA85F000 00010C (v05 APM XGENE 00000003 INTL
20140724)
ACPI: DSDT 0x00000047FA860000 00495F (v05 APM APM88xxx 00000001 INTL
20140724)
ACPI: DBG2 0x00000047FA865000 0000AA (v00 APMC0D XGENEDBG 00000000 INTL
20140724)
ACPI: GTDT 0x00000047FA85D000 0000E0 (v02 APM XGENE 00000001 INTL
20140724)
ACPI: MCFG 0x00000047FA85C000 00003C (v01 APM XGENE 00000002 INTL
20140724)
ACPI: SPCR 0x00000047FA85B000 000050 (v02 APMC0D XGENESPC 00000000 INTL
20140724)
ACPI: SSDT 0x00000047FA85A000 00002D (v02 APM XGENE 00000001 INTL
20140724)
ACPI: APIC 0x00000047FA859000 0002A4 (v03 APM XGENE 00000003
01000013)
ACPI: SSDT 0x00000047FA858000 000078 (v02 REDHAT MACADDRS 00000001
01000013)
ACPI: SSDT 0x00000047FA857000 000032 (v02 REDHAT UARTCLKS 00000001
01000013)
psci: is not implemented in ACPI.
Unsupported ACPI enable-method
Unsupported ACPI enable-method
Unsupported ACPI enable-method
Unsupported ACPI enable-method
Unsupported ACPI enable-method
Unsupported ACPI enable-method
Unsupported ACPI enable-method
Unsupported ACPI enable-method
PERCPU: Embedded 2 pages/cpu @fffffe07fff90000 s41472 r8192 d81408 u131072
Detected PIPT I-cache on CPU0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 523776
Kernel command line: BOOT_IMAGE=/vmlinuz-4.5.0-rc1+
root=UUID=0e305934-49d5-4f66-b10b-23ec6029fab9 ro acpi=force
earlycon=uart8250,mmio32,0x1c020000 console=ttyS0,115200 LANG=en_US.UTF-8
PID hash table entries: 4096 (order: -1, 32768 bytes)
Dentry cache hash table entries: 4194304 (order: 9, 33554432 bytes)
Inode-cache hash table entries: 2097152 (order: 8, 16777216 bytes)
software IO TLB [mem 0x40dbff0000-0x40dfff0000] (64MB) mapped at
[fffffe00dbff0000-fffffe00dffeffff]
Memory: 32856256K/33554432K available (6158K kernel code, 725K rwdata,
4032K rodata, 768K init, 399K bss, 173888K reserved, 524288K cma-reserved)
Virtual kernel memory layout:
vmalloc : 0xfffffc0000000000 - 0xfffffdfedfff0000 ( 2043 GB)
vmemmap : 0xfffffdfee0000000 - 0xfffffdffe0000000 ( 4 GB maximum)
0xfffffdfef0000000 - 0xfffffdfef2000000 ( 32 MB actual)
fixed : 0xfffffdfffa7d0000 - 0xfffffdfffac00000 ( 4288 KB)
PCI I/O : 0xfffffdfffae00000 - 0xfffffdfffbe00000 ( 16 MB)
modules : 0xfffffdfffc000000 - 0xfffffe0000000000 ( 64 MB)
memory : 0xfffffe0000000000 - 0xfffffe0800000000 ( 32768 MB)
.init : 0xfffffe0000a80000 - 0xfffffe0000b40000 ( 768 KB)
.text : 0xfffffe0000080000 - 0xfffffe0000a75b44 ( 10199 KB)
.data : 0xfffffe0000b40000 - 0xfffffe0000bf5400 ( 725 KB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 64.
RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=1.
RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=1
NR_IRQS:64 nr_irqs:64 0
GIC: Using split EOI/Deactivate mode
Architected cp15 timer(s) running at 50.00MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles:
0xb8812736b, max_idle_ns: 440795202655 ns
sched_clock: 56 bits at 50MHz, resolution 20ns, wraps every 4398046511100ns
Console: colour dummy device 80x25
Calibrating delay loop (skipped), value calculated using timer
frequency.. 100.00 BogoMIPS (lpj=200000)
pid_max: default: 32768 minimum: 301
ACPI: Core revision 20160108
ACPI: 4 ACPI AML tables successfully acquired and loaded
Security Framework initialized
Mount-cache hash table entries: 65536 (order: 3, 524288 bytes)
Mountpoint-cache hash table entries: 65536 (order: 3, 524288 bytes)
ASID allocator initialised with 65536 entries
Is the patch set supposed to be evaluated without ACPI?
next reply other threads:[~2016-02-13 5:05 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-02-13 4:56 Itaru Kitayama [this message]
2016-02-13 5:52 ` [PATCH v6 0/3] mailbox: Add APM X-Gene platform mailbox driver Duc Dang
-- strict thread matches above, loose matches on Subject: below --
2016-02-10 14:41 [PATCH v5 1/3] mailbox: Add support for " Mathieu Poirier
2016-02-13 3:39 ` [PATCH v6 0/3] mailbox: Add " Duc Dang
2016-02-13 3:39 ` Duc Dang
2016-02-13 3:39 ` Duc Dang
2016-02-19 20:43 ` Duc Dang
2016-02-19 20:43 ` Duc Dang
2016-02-19 20:43 ` Duc Dang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=56BEB783.1050105@riken.jp \
--to=itaru.kitayama@riken.jp \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.